Marantz SA8005 Owner's Manual in English - Page 57

Switching the function of the volume buttons on the remote control

Get Marantz SA8005 PDF manuals and user guides View all Marantz SA8005 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Contents Connections Playback Settings Tips Appendix Switching the function of the volume buttons on the remote control When the function of the VOLUME df buttons on the remote control is set to "Variable", the analog audio output level can be adjusted. AMP (Default) : A djusts the volume of Marantz amplifiers. Variable : Adjusts the analog audio output level of the analog audio signal output from this unit. % • Check the operation of this unit and connected devices after setting the function of the VOLUME df buttons on the remote control. Set the function of the volume buttons on the remote control to "Variable" Set the function of the volume buttons on the remote control to "AMP" 1 Press and hold the ENTER and number 2 button down together for more than 5 seconds. The remote mode selection button (REMOTE MODE NET) lights for approximately 1 second. NOTE • The remote control returns to the factory settings when the batteries are removed. Therefore, set the remote control code again after replacing the batteries. 1 Press and hold the ENTER and number 1 button down together for more than 5 seconds. The remote mode selection button (REMOTE MODE CD) lights for approximately 1 second. NOTE • To adjust the analog audio signal output from this unit using the remote control, also set "Audio Out" (vpage 55) to "Variable". Front panel Display Rear panel 57 Remote Index

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
57
Appendix
Tips
Playback
Connections
Contents
Front panel
Display
Rear panel
Index
Remote
Settings
Switching the function of the volume buttons on the remote control
When the function of the VOLUME
df
buttons
on the remote control is
set to “Variable”, the analog audio output level can be adjusted.
AMP
(Default) : Adjusts the volume of Marantz amplifiers.
Variable
: Adjusts the analog audio output level of the analog audio signal
output from this unit.
%
•
Check the operation of this unit and connected devices after setting the function of
the VOLUME
df
buttons on the remote control.
Set the function of the volume buttons
on the remote control to “Variable”
1
Press and hold the ENTER and number 1 button down
together for more than 5 seconds.
The remote mode selection button
(
REMOTE MODE CD
)
lights for
approximately 1 second.
NOTE
•
To adjust the analog audio signal output from this unit using the remote control,
also set “Audio Out” (
v
page 55) to “Variable”.
Set the function of the volume buttons
on the remote control to “AMP”
1
Press and hold the ENTER and number 2 button down
together for more than 5 seconds.
The remote mode selection button
(
REMOTE MODE NET
)
lights
for approximately 1 second.
NOTE
•
The remote control returns to the factory settings when the batteries are removed.
Therefore, set the remote control code again after replacing the batteries.