Marantz SC-7S2 SC-7S2 User Manual - Page 17

Rear Panel

Get Marantz SC-7S2 PDF manuals and user guides View all Marantz SC-7S2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

ENGLISH NAME AND FUNTION REAR PANEL PUSH PUSH z x c v b nm , . z Input Balanced terminal This terminal is to connect the components which have balanced outputs i.e. CD Player. When Bi-Amping, terminal B can not be used. Balanced terminal → p5 x Input CD, Line 1, Line 2, Recorder (Unbalanced) terminal This terminal is to connect the unbalanced terminals of components., i.e. CD etc. When Bi-Amping, terminal B can not be used. c Rec out terminal The terminal connects to the Input of Recording equipment i.e. CD Recorders, Tape Recorder etc. When Bi-Amping, the signal being input to channel A, will be output to both A & B channels. v Pre out Unbalanced 1,2 terminal This connects to the un balanced inputs of a Power Amp. When Bi-Amping, the signal being input to channel A, will be output to both A & B channels. b Pre out Balanced terminal This terminal is connected to the Balanced input of the Power Amplifier. When Bi-Amping, the signal being input to channel A, will be output to both A & B channels. n F.C.B.S. In/Out terminal These terminals are for connecting one or more SC-7S2s to each other. The IN is for receiving control signals. The OUT is for sending Control signals. m ID No. switch Whilst several SC-7S2 are connected, to set up respective ID No. to distinguish each products. When only 1 unit is used, the No. will be set 1. Initial setting is . This switch is to give ID numbers to each SC-7S2, when two or more are used. When using only 1, SC-7S2 the ID switch is set to 1. Factory setting is 1. Trim adjustment in case of several units of SC-7S2 → p18 If using 2 or more SC-7S2s, you can use the trim Adjustment. See page 18. , Mode switch The switch to change Stereo mode and Bi-Amp mode. Initial setting is . • In case SC-7S2 is used for normal 2 channel. Setting mode. • In case of complete Bi-Amp connection with 2 units of SC-7S2. Setting mode. In case of mode, the signal input from A channel will be out to both of A/B channels through Preout terminal and Rec out terminal. Then, input terminal on B channel can not be used. This switch is to switch between Stereo & Bi-Amp Mode. Factory setting is Stereo. Stereo is used for using only 1 SC-7S2. If using 2 or more SC-7S2s, you will set the switch to Bi-Amp Mode. When Bi-Amping, the signal being input to channel A, will be outputted to both A & B channels through the Pre-out & REC out terminals. The B input terminal can not be used in Bi-Amp Mode. . AC IN socket Connect to a household power outlet with supplied AC CORD. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
ENGLISH
13
REAR PANEL
PUSH
PUSH
z
b
v
c
n
,
.
m
x
NAME AND FUNTION
z
Input Balanced terminal
This terminal is to connect the components which have
balanced outputs i.e. CD Player.
When Bi-Amping, terminal B can not be used.
Balanced terminal
→
p5
x
Input CD, Line 1, Line 2, Recorder (Unbal-
anced) terminal
This terminal is to connect the unbalanced terminals of
components., i.e. CD etc.
When Bi-Amping, terminal B can not be used.
c
Rec out terminal
The terminal connects to the Input of Recording equip-
ment i.e. CD Recorders, Tape Recorder etc.
When Bi-Amping, the signal being input to channel A, will
be output to both A & B channels.
v
Pre out Unbalanced 1,2 terminal
This
connects to the un balanced inputs of a Power Amp.
When Bi-Amping, the signal being input to channel A, will
be output to both A & B channels.
b
Pre out Balanced terminal
This terminal is connected to the Balanced input of the
Power Amplifier. When Bi-Amping, the signal being input
to channel A, will be output to both A & B channels.
n
F.C.B.S. In/Out terminal
These terminals are for connecting one or more SC-7S2s
to each other. The IN is for receiving control signals. The
OUT is for sending Control signals.
m
ID No. switch
Whilst several SC-7S2 are connected, to set up respective
ID No. to distinguish each products.
When only 1 unit is used, the No. will be set 1.
Initial set-
ting is <1>.
This switch is to give ID numbers to each SC-7S2, when
two or more are used. When using only 1, SC-7S2 the ID
switch is set to 1. Factory setting is 1.
Trim adjustment in case of several units of SC-7S2
→
p18
If using 2 or more SC-7S2s, you can use the trim Adjust-
ment.
See page 18.
,
Mode switch
The switch to change Stereo mode and Bi-Amp mode.
Initial setting is <stereo>.
• In case SC-7S2 is used for normal 2 channel.
Setting <Stereo> mode.
• In case of complete Bi-Amp connection with 2 units of
SC-7S2.
Setting <Bi-Amp> mode.
In case of <Bi-Amp> mode, the signal input from A
channel will be out to both of A/B channels through Pre-
out terminal and Rec out terminal.
Then, input terminal on B channel can not be used.
This switch is to switch between Stereo & Bi-Amp Mode.
Factory setting is Stereo. Stereo is used for using only 1
SC-7S2. If using 2 or more SC-7S2s, you will set the switch
to Bi-Amp Mode. When Bi-Amping, the signal being input
to channel A, will be outputted to both A & B channels
through the Pre-out & REC out terminals. The B input ter-
minal can not be used in Bi-Amp Mode.
.
AC IN socket
Connect to a household power outlet with supplied AC
CORD.