Marantz SR8400 SR8400 User Manual - Page 11

ENGLISH , MUTE button This button is used to mute the audio for the SR8400 and television. Note: • Set the AMP mode to use this button with the SR8400. . GUIDE button This button is used to display the menus for the DVD player, DSS (satellite broadcasting tuner), or other AV equipment. ⁄0 EXIT button (when AMP mode is selected) This button is used to cancel settings in the setup menu. ⁄1 Numeric buttons These buttons are used to switch between 0 to 9 of the source components. If the source is set to the amplifier, these buttons are used to perform operations. (when AMP mode is selected) (1) TEST button Used to enter the test tone menu. (2) CH SEL. (channel select) button Used to call up SETUP MAIN MENU and adjust speaker levels or 7.1 ch input level. (3) SURR (surround) button Used to select the surround mode. (4) 7.1CH IN button Press this button to select the output of an external multi channel decoder. (5) ATT button When the input signal is too high and the voice distorts even by throttling the SR8400 VOLUME control, turn on this function. "ATT" is indicated when this function is activated. The input level is reduced. Attenuator is invalid for use with the output signal of "REC OUT". Note: • This function is unavailable during the digital input is selected. (6) SPK-AB button Speaker mode is switched in the following sequence. A → B → A+B → off (7) DISP. button Selects the display mode for the front display of the SR8400. (8) OSD button When this button is pressed, the current setting are displayed on the TV monitor. (9) SLEEP (sleep timer) button This button is used for setting the sleep timer. It can be operated the same way as the button in unit. ⁄2 MEMO button This button is used to store settings to memory or program a source. ⁄3 CONTROL button Thses buttons are used when operating the PLAY, STOP, PAUSE, and other commands of a source. Note: • This button is unavailable for the SR8400. ⁄4 SOURCE button Thses buttons are used to switch the source of your A/V Receiver / amplifer. Each time a source button is pressed, the remote control changes to the source which was pressed. This remote control can control 12 types of equipment. To change the A/V Receiver / amplifier source, press this button twice within two seconds. The signal is sent when it is pressed the second time. Note: • Select the AMP as the source to use this remote controll with the SR8400. ⁄5 LIGHT 1 and 2 buttons Pressing these buttons will light up the LCD and its buttons. This lighting time can be set. If the lighting time is set to 0 seconds, the backlight turns on only while this button is pressed. The operations for LIGHT 1 and 2 are identical. ⁄6 CLEAR button This button is used to erase the memory or program of a source. ⁄7 MENU button (when AMP mode is selected) This button is used to call up the SETUP MAIN MENU of the SR8400. ⁄8 PREV (Previous) button This button is used to return to the previous channel on the television or other device. Note: • This button is unavailable for SR8400. ⁄9 CH (Channel) button This is used to change channels. ¤0 CURSOR buttons These buttons are used when controlling the cursor of the SR8400, DVD, or other AV equipment. ¤1 LCD Information about the sources and modes are shown on the LCD. LCD INDICATORS Information about currently selected source and direct code names are displayed on the LCD. A J LEARN I NAME B H MACRO G F E USE PAGE 1 2 3 4 C D A Source Name indicator This displays the name of the selected source, such as DVD, television, or other AV equipment (up to five characters). B Direct Button Name indicator This displays up to 20 types of button names for each source. (up to six characters) C Page indicator This displays the current page position. D Transmission indicator This lights up when the remote control is sending a signal. E USE indicator This is displayed under normal operation. F Battery Level indicator This is displayed when the battery level is low. G TIMER indicator This is displayed when the macro timer is set. H MACRO indicator This is displayed when the remote control is in macro programming mode. 8