NEC 2010x User Manual - Page 23

Installation - manual

Get NEC 2010x - MultiSync - 20.1inch LCD Monitor PDF manuals and user guides View all NEC 2010x manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

English Deutsch Français Installation E - 8 Installation Connection to your Personal Computer The MultiSync LCD2010X true colour monitor complements PC compatible computers. Your system has one of two configurations: - the video controller is built into the computer. - the video controller is in the form of a display card (sometimes referred to as graphics card, video adapter or graphics board). Both configurations have a video connector (or a CRT PORT on laptop computers). If you are not sure which connector is the video connector, refer to your computer or display card manual. To attach the MultiSync LCD2010X monitor to your system, follow these instructions: 1. Turn off the power of your computer. 2. For the PC with DVI digital output: Connect the DVI-D to DVI-D signal cable to the connector of the display card in your system (Figure A.1). Tighten all screws. For the PC with Analog output: Connect the 15-pin mini DSUB to DVI signal cable to the connector of the display card in your system (Figure A.2). To connect a secondary PC with analog output, connect the 15-pin mini D-SUB to 15-pin mini D-SUB signal cable (not include) to the connector of the display card in your system. For the Mac: Connect the MultiSync Macintosh cable adapter to the computer (Figure B.1). Attach the 15-pin mini D-SUB signal cable to the MultiSync Macintosh cable adapter (Figure B.1). NOTE: Some Macintosh systems do not require a Macintosh cable adapter. Español Italiano Appendix CN971B/LCD2010X/7A812101 23 00.8.30, 2:21 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
Appendix
Español
Français
Deutsch
English
Italiano
Installation
Connection to your Personal Computer
The MultiSync LCD
2010X
true colour monitor complements PC
compatible computers. Your system has one of two configurations:
–
the video controller is built into the computer.
–
the video controller is in the form of a display card (sometimes
referred to as graphics card, video adapter or graphics board).
Both configurations have a video connector (or a CRT PORT on laptop
computers). If you are not sure which connector is the video connector,
refer to your computer or display card manual.
To attach the MultiSync LCD
2010X
monitor to your system,
follow these instructions:
1.
Turn off the power of your computer.
2.
For the PC with DVI digital output:
Connect the DVI-D to
DVI-D signal cable to the connector of the display card in your
system (Figure A.1). Tighten all screws.
For the PC with Analog output:
Connect the 15-pin mini D-
SUB to DVI signal cable to the connector of the display card
in your system (Figure A.2).
To connect a secondary PC with analog output, connect the
15-pin mini D-SUB to 15-pin mini D-SUB signal cable (not
include) to the connector of the display card in your system.
For the Mac:
Connect the MultiSync Macintosh cable adapter to
the computer (Figure B.1). Attach the 15-pin mini D-SUB signal
cable to the MultiSync Macintosh cable adapter (Figure B.1).
NOTE:
Some Macintosh systems do not require a Macintosh cable adapter.
Installation
E - 8
CN971B/LCD2010X/7A812101
00.8.30, 2:21 PM
23