NEC 70GX2-BK MultiSync 70GX2 & 90GX2 User Manual - Page 5

Display Setup - display solutions

Get NEC 70GX2-BK - MultiSync - 17inch LCD Monitor PDF manuals and user guides View all NEC 70GX2-BK manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Display Setup To attach the MultiSync® LCD monitor to your system, follow these instructions: 1. Turn off the power to your computer. 2. For the PC or MAC with DVI digital output : Connect the DVI signal cable to the connector of the display card in your system (Figure 1). Tighten all screws. For the PC with Analog output: Connect the 15-pin mini D-SUB signal cable to the connector of the display card in your system (Figure 2). Tighten all screws. For MAC setup: Connect the Macintosh cable adapter to the computer, then attach the 15-pin mini D-SUB signal cable to the Macintosh cable adapter (Figure 3). Tighten all screws. NOTE: To obtain the MultiSync Macintosh cable adapter, call NEC Display Solutions of America, Inc. at (800) 632-4662. 3. Remove the connector cover (Figure 4). 4. Place hands on each side of the monitor and tilt the LCD panel 30° (Figure 5). 5. Connect all cables to the appropriate connectors through the square hole in the stand (Figure 6). 6. Place the connector cover onto the back cabinet (Figure 7). 7. Place all cables into the hooks (Figure 8). 8. Place hands on each side if the monitor to tilt the LCD panel back 5° (Figure 9). 9. Place the cable cover onto the stand (Figure 9). To remove the cable cover, push the notch at the bottom of the cover up (towards the top of the monitor) in order to unhook the cover from the stand (Figure 10). 10. Connect the power cord to the power outlet (Figure 11). NOTE: If you use this monitor at AC125-240V, please refer to Recommended Use section of this manual for proper selection of power cord. 11. The vacation switch on the back side of the monitor must be turned on (Figure 11). Turn on the monitor with the front power button and power on the computer. NOTE: The vacation switch is a true on/off switch. If this switch is in the OFF position, the monitor cannot be turned on using the front button. DO NOT switch on/off repeatedly. 12. Analog input only: No-Touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup most of the time. For further adjustments, use the following OSM® controls: • Auto Adjust Contrast • Auto Adjust Refer to the Controls section of this User 's Manual for a full description of these OSM controls. NOTE: For download information on the Windows® 95/98/Me/2000/XP INF file for your monitor, refer to the References section of this User's Manual. NOTE: If you have any problems, please refer to the Troubleshooting section of this User's Manual. 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
3
Display Setup
To attach the MultiSync
®
LCD monitor to your system, follow these instructions:
±.
Turn off the power to your computer.
2.
For the PC or MAC with DVI digital output
: Connect the DVI signal cable to the
connector of the display card in your system
(Figure 1)
. Tighten all screws.
For the PC with Analog output
: Connect the ±5-pin mini D-SUB signal cable to the
connector of the display card in your system
(Figure 2)
. Tighten all screws.
For MAC setup
: Connect the Macintosh cable adapter to the computer, then attach
the ±5-pin mini D-SUB signal cable to the Macintosh cable adapter
(Figure 3)
.
Tighten all screws.
NOTE: To obtain the MultiSync Macintosh cable adapter, call
NEC Display Solutions of America, Inc. at (800) 632-4662.
3.
Remove the connector cover (Figure 4).
4.
Place hands on each side of the monitor and tilt the LCD panel 30° (Figure 5).
5.
Connect all cables to the appropriate connectors through the square hole in the stand
(Figure 6).
6.
Place the connector cover onto the back cabinet (Figure 7).
7.
Place all cables into the hooks (Figure 8).
8.
Place hands on each side if the monitor to tilt the LCD panel back 5° (Figure 9).
9.
Place the cable cover onto the stand (Figure 9). To remove the cable cover, push
the notch at the bottom of the cover up (towards the top of the monitor) in order to
unhook the cover from the stand (Figure ±0).
±0. Connect the power cord to the power outlet
(Figure 11)
.
NOTE: If you use this monitor at AC125-240V, please refer to Recommended Use
section of this manual for proper selection of power cord.
±±. The vacation switch on the back side of the monitor must be turned on
(Figure 11)
.
Turn on the monitor with the front power button and power on the computer.
NOTE: The vacation switch is a true on/off switch. If this switch is in the OFF
position, the
monitor cannot be turned on using the front button.
DO NOT switch on/off repeatedly.
±2. Analog input only: No-Touch Auto Adjust automatically adjusts the monitor to optimal
settings upon initial setup most of the time. For further adjustments, use the following
OSM
®
controls:
• Auto Adjust Contrast
• Auto Adjust
Refer to the Controls section of this User ’s Manual for a full description of these
OSM controls.
NOTE:
For download information on the Windows
®
95/98/Me/2000/XP INF
file for your monitor, refer to the
References
section of this User’s Manual.
NOTE:
If you have any problems, please refer to the
Troubleshooting
section of
this User’s Manual.