Home » Netgear Manuals » Bridges & Routers » Netgear AX11000 » Manual Viewer

Netgear AX11000 User Manual - Page 67

Change the WiFi mode

Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Nighthawk Tri-Band AX12 12-Stream AX WiFi Router 7. To change the network name (SSID), type a new name in the Name (SSID) field. The name can be up to 32 characters long and it is case-sensitive. The default SSID is randomly generated and is on the router label. If you change the name, make sure to write down the new name and keep it in a safe place. 8. To change the WiFi channel, select a number from the Channel menu. In some regions, not all channels are available. Do not change the channel unless you experience interference (shown by lost connections or slow data transfers). If this happens, experiment with different channels to see which is the best. When you use multiple access points, it is better if adjacent access points use different channels to reduce interference. The recommended channel spacing between adjacent access points is four channels (for example, use Channels 1 and 5, or 6 and 10). 9. Click the Apply button. Your settings are saved. If you connected wirelessly to the network and you changed the SSID, you are disconnected from the network. 10. Make sure that you can connect wirelessly to the network with its new settings. If you cannot connect wirelessly, check the following: • Is your computer or mobile device connected to another WiFi network in your area? Some WiFi devices automatically connect to the first open network without WiFi security that they discover. • Is your computer or mobile device trying to connect to your network with its old settings (before you changed the settings)? If so, update the WiFi network selection in your computer or mobile device to match the current settings for your network. Change the WiFi mode The WiFi mode options for the 2.4 GHz, 5 GHz-1, and 5 GHz-2 WiFi networks depend on whether AX WiFi is enabled. For more information about AX WiFi , see Enable or disable AX WiFi on page 97. Manage Network Settings 67 User Manual

Section	Page
Contents	3
1. Hardware Setup	9
Unpack your router	10
Top panel LEDs and buttons	11
Rear panel	14
Extend the antennas	15
Router label	16
Position your router	16
Cable your router	17
2. Connect to Network and Access the Router	19
Connect to the network	20
Connect to the network using a wired connection	20
Find and connect to the WiFi network	20
WiFi connection using WPS	20
Types of logins	21
Install and manage your router with the Nighthawk app	21
Use a web browser to access the router	22
Automatic Internet Setup	22
Log in to the router	23
Change the language	24
3. Specify Your Internet Settings	25
Use the Internet Setup Wizard	26
Manually set up the Internet connection	26
Specify an Internet connection without a login	26
Specify an Internet connection that uses a login	28
Set up the Multi-Gig port on your router	30
Get Multi-Gig Internet With Internet Port Aggregation	31
Specify IPv6 Internet connections	32
Requirements for entering IPv6 addresses	32
Use auto detect for an IPv6 Internet connection	33
Set up an IPv6 6to4 tunnel Internet connection	34
Set up an IPv6 pass-through Internet connection	35
Set up an IPv6 fixed Internet connection	36
Set up an IPv6 DHCP Internet connection	37
Set up an IPv6 PPPoE Internet connection	39
Use auto config for an IPv6 Internet connection	40
Set up an IPv6 6rd Internet connection	42
Manage the MTU size	44
MTU concepts	44
Change the MTU size	45
4. Control Access to the Internet	46
Enable access control to allow or block access to the Internet	47
Use keywords to block Internet sites	48
Block services from the Internet	50
Delete keywords from the blocked list	51
Prevent blocking on a trusted computer	51
Manage network access control lists	52
Schedule when to block Internet sites and services	53
Set up security event email notifications	54
5. Manage Network Settings	56
View or change the WAN settings	57
Set up a default DMZ server	58
Change the Router’s Device Name	59
Change the LAN TCP/IP settings	59
Specify the IP addresses that the router assigns	61
Disable the DHCP server feature in the router	62
Manage reserved LAN IP addresses	63
Reserve an IP address	63
Edit a reserved IP address	64
Delete a reserved IP address entry	64
Use the WPS Wizard for WiFi connections	65
Specify Basic WiFi Settings	66
Change the WiFi mode	67
Change the WiFi mode if AX WiFi is enabled	68
Change the WiFi mode if AX WiFi is disabled	69
Change the WiFi password or the WiFi security	71
Set up a guest WiFi network	72
Control the WiFi radios	75
Use the WiFi On/Off button	75
Enable or disable the WiFi radios	75
Set up a WiFi schedule	76
Specify WPS settings	77
Set up the router as a WiFi access point	78
Set up a bridge for a port group or VLAN tag group	79
Set up a bridge for a port group	79
Set up a bridge for a VLAN tag group	80
Set up an IPTV port	81
Manage custom static routes	82
Set up a static route	83
Edit a static route	84
Delete a static route	85
Enable or disable implicit beamforming	85
Enable or disable airtime fairness	86
Enable or disable MU-MIMO	87
Set Up the Router in Bridge Mode	88
Ethernet Port Aggregation	89
Set Up Ethernet Port Aggregation	90
View or Change the Router Ethernet Port Aggregation Mode	91
6. Optimize Performance	92
Use Dynamic QoS to optimize Internet traffic management	93
Enable Dynamic QoS	93
Enable or disable the automatic QoS database update	94
Manually update the dynamic QoS database	94
Improve network connections with Universal Plug and Play	95
Wi-Fi Multimedia Quality of Service	96
Enable or disable AX WiFi	97
Enable or disable Smart Connect	98
7. Manage Your Router	100
Update the router firmware	101
Check for new firmware and update the router	101
Manually upload firmware to the router	102
Change the admin password	103
Enable admin password recovery	103
Recover the admin password	104
View information about the router and the Internet and WiFi settings	105
Display the statistics of the Internet port	106
Check the Internet connection status	107
View and manage logs of router activity	108
View devices currently on the network	109
Monitor Internet traffic	109
Manage the router configuration file	111
Back up the settings	111
Erase the settings	111
Restore the settings	112
Remote access	113
Set up remote management	113
Use remote access	114
Remotely access your router using the Nighthawk app	114
Disable LED blinking or turn off LEDs	115
Set your time zone	115
Set the NTP Server	116
Specify ReadyDLNA Media Server Settings	117
Return the router to its factory default settings	118
Use the Reset button	118
Erase the settings	118
8. Share USB Storage Devices Attached to the Router	120
USB device requirements	121
Connect a USB storage device to the router	121
Access a storage device connected to the router from a Windows-based computer	122
Map a USB device to a Windows network drive	122
Access a storage device that is connected to the router from a Mac	123
Back up Windows-based computers with ReadySHARE Vault	124
Back up Mac computers with Time Machine	124
Set up a USB hard drive on a Mac	125
Prepare to back up a large amount of data	126
Use Time Machine to back up onto a USB hard disk	126
Enable FTP access within your network	128
View network folders on a storage device	128
Add a network folder on a USB storage device	129
Edit a network folder on a USB storage device	130
Safely remove a USB storage device	131
9. Use Dynamic DNS to Access USB Storage Devices Through the Internet	132
Set up and manage Dynamic DNS	133
Set up FTP access through the Internet	133
Your personal FTP server	134
Set up your personal FTP server	134
Set up a new Dynamic DNS account	135
Specify a DNS account that you already created	135
Change the Dynamic DNS settings	136
Access USB storage devices through the Internet	137
Remotely access a USB device using ReadyCLOUD	138
Create a ReadyCLOUD account	138
Register your router with ReadyCLOUD	138
10. Use VPN to Access Your Network	140
Set up a VPN connection	141
Specify VPN Service in the Router	141
Install OpenVPN Software	142
Install OpenVPN Software on Your Windows Computer	142
Install OpenVPN Software on Your Mac Computer	145
Install OpenVPN Software on an iOS Device	146
Install OpenVPN Software on an Android Device	146
Use a VPN Tunnel on Your Windows Computer	147
Use VPN to Access the Router’s USB Device and Media	149
Use VPN to Access Your Internet Service at Home	149
Set Up VPN Client Internet Access in the Router	150
Block VPN Client Internet Access in the Router	150
Use a VPN Tunnel to Access Your Internet Service at Home	151
11. Manage Port Forwarding and Port Triggering	153
Manage Port Forwarding to a Local Server	154
Set Up Port Forwarding to a Local Server	154
Add a Custom Port Forwarding Service	155
Edit a Port Forwarding Service	156
Delete a Port Forwarding Entry	157
Application Example: Make a Local Web Server Public	157
How the Router Implements the Port Forwarding Rule	158
Port Triggering	158
Add a Port Triggering Service	159
Enable Port Triggering	160
Application Example: Port Triggering for Internet Relay Chat	160
12. Troubleshooting	162
Quick tips	163
Sequence to restart your network	163
Check the power adapter and Ethernet cable connections	163
Check the WiFi settings	163
Check the network settings	163
Troubleshoot with the LEDs	164
Standard LED behavior when the router is powered on	164
Power LED is off or blinking	164
LEDs never turn off	164
Internet or Ethernet LAN port LEDs are off	165
WiFi LED is off	165
You cannot log in to the router	165
You cannot access the Internet	166
Troubleshoot Internet browsing	168
Changes are not saved	168
Troubleshoot WiFi connectivity	169
Troubleshoot your network using the ping utility	169
Test the LAN path to your router	169
Test the path from a Windows-based computer to a remote device	170
13. Supplemental Information	172
Factory settings	173

Match case Limit results 1 per page

To change the network name (SSID), type a new name in the

Name (SSID)

field.

The name can be up to 32 characters long and it is case-sensitive. The default SSID

is randomly generated and is on the router label. If you change the name, make sure

to write down the new name and keep it in a safe place

To change the WiFi channel, select a number from the

Channel

menu.

In some regions, not all channels are available. Do not change the channel unless

you experience interference (shown by lost connections or slow data transfers). If

this happens, experiment with different channels to see which is the best.

When you use multiple access points, it is better if adjacent access points use different

channels to reduce interference. The recommended channel spacing between

adjacent access points is four channels (for example, use Channels 1 and 5, or 6 and

10).

Click the

Apply

button.

Your settings are saved.

If you connected wirelessly to the network and you changed the SSID, you are

disconnected from the network.

10. Make sure that you can connect wirelessly to the network with its new settings.

If you cannot connect wirelessly, check the following:

•

Is your computer or mobile device connected to another WiFi network in your

area? Some WiFi devices automatically connect to the first open network without

WiFi security that they discover.

•

Is your computer or mobile device trying to connect to your network with its old

settings (before you changed the settings)? If so, update the WiFi network selection

in your computer or mobile device to match the current settings for your network.

Change the WiFi mode

The WiFi mode options for the 2.4 GHz, 5 GHz-1, and 5 GHz-2 WiFi networks depend

on whether AX WiFi is enabled. For more information about AX WiFi , see Enable

disable

WiFi

on page 97.

User Manual

Manage Network Settings

Nighthawk Tri-Band AX12 12-Stream AX WiFi Router