NordicTrack T 12.0 Instruction Manual - Page 12

May Become Damaged When You Turn

Get NordicTrack T 12.0 PDF manuals and user guides View all NordicTrack T 12.0 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

11. With the help of a second person, hold the console assembly (G) near the Handrail (72). 11 Connect the three ground wires (H) from the G console assembly (G) to the three Console Ground Wires (76) on the Pulse Crossbar (75). Next, insert the Upright Wire (80) through the two indicated looped ties (I). J See the inset drawing. Connect the Upright Wire (80) to the console wire (J). The connec- tors should slide together easily and snap into place. If they do not, turn one connector and try again. IF YOU DO NOT CONNECT THE CONNECTORS PROPERLY, THE CONSOLE MAY BECOME DAMAGED WHEN YOU TURN ON THE POWER. Then, remove the wire tie (A) 72 from the Upright Wire. I 76 80 75 A 76 H J 80 12. Set the console assembly (G) on the Handrails (72). Make sure that no wires are pinched. Insert the excess Upright Wire (80) into the console assembly. Then, tighten the two ties (I) around the Upright Wire and cut off the ends of the ties. Attach the console assembly (G) to the brackets on the Handrails (72) with the four 5/16" x 3/4" Screws (13) that you removed in step 9 and four 5/16" Star Washers (7); do not tighten the Screws yet. 12 G 80 72 I 7 13 79 72 7 13 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
12
11.
With the help of a second person, hold the con-
sole assembly (G) near the Handrail (72).
Connect the three ground wires (H) from the
console assembly (G) to the three Console
Ground Wires (76) on the Pulse Crossbar (75).
Next, insert the Upright Wire (80) through the
two indicated looped ties (I).
See the inset drawing.
Connect the Upright
Wire (80) to the console wire (J).
The connec-
tors should slide together easily and snap
into place.
If they do not, turn one connector
and try again.
IF YOU DO NOT CONNECT THE
CONNECTORS PROPERLY, THE CONSOLE
MAY BECOME DAMAGED WHEN YOU TURN
ON THE POWER.
Then, remove the wire tie (A)
from the Upright Wire.
11
G
I
J
76
76
J
80
H
A
80
72
75
12.
Set the console assembly (G) on the Handrails
(72).
Make sure that no wires are pinched.
Insert the excess Upright Wire (80) into the
console assembly. Then, tighten the two ties (I)
around the Upright Wire and cut off the ends of
the ties.
Attach the console assembly (G) to the brackets
on the Handrails (72) with the four 5/16" x 3/4"
Screws (13) that you removed in step 9 and
four 5/16" Star Washers (7);
do not tighten the
Screws yet.
12
79
G
I
13
7
13
7
80
72
72