Oki B4350n PostScript 3 emulation Kit Installation Instructions - Page 1

Oki B4350n Manual

Get Oki B4350n PDF manuals and user guides View all Oki B4350n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

PostScript® 3™ emulation Kit Installation Instructions PostScript 3 emulation Kit Part Number: 70049601 1. Unpack the cards and remove any shipping materials. The PostScript card is marked PS on the label. The memory card is marked 16MB on the label. 2. Turn off the printer, and remove the power cord and interface cable. NOTE: If you have a network card installed, remove it temporarily before installing the PostScript option. 3. Loosen the access panel screw. b. Position the card into the connector. 7. Check to make sure that both cards are fully inserted and installed correctly. 8. Replace the access panel: a. Align the panel tabs at bottom. b. Swing the panel up and in place. c. Tighten the screw. 4. Remove the access panel and locate the PostScript connector (1). c. Press down on the card until it snaps into place and the gold contacts are fully inserted in the connector. 6. Install the memory chip: Insert the card with the notch towards the front of the printer. Press down on the card until it snaps into place and the gold contacts are fully inserted in the connector. 5. Install the PostScript card: a. Hold the card (make sure PS is on the label) so that the notch (2) is on the bottom right corner. Oki Data Americas, Inc., Mt. Laurel, NJ 08054 http://www.okidata.com 9. Verify Installation Print a Menu Map: a. Press the Menu button one or more times until INFO.MENU appears on the display. b. Press SELECT twice. The MenuMap prints. c. PSE Program version and Total Memory Size 32 MB appears in the header, and PRINT PSE FONT in the Information Menu. If not, check to be sure that the cards are installed correctly. Your printer is factory set to AUTO EMULATION (AUTO appears on the printer display). In this setting the printer will sample data and automatically switch between PostScript emulation and the other emulations. If the printer is not set to AUTO EMULATION, see the User's Guide for instructions to set it in the prin(tCeroMnteinnuue. d on back) 58369502

  • 1
  • 2
PostScript
®
3
™
emulation Kit
Installation Instructions
PostScript 3 emulation Kit Part Number: 70049601
Oki Data Americas, Inc., Mt. Laurel, NJ 08054
1.
Unpack the cards and remove any
shipping materials. The
PostScript card is marked PS on
the label. The memory card is
marked 16MB on the label.
2.
Turn off the printer, and remove
the power cord and interface
cable.
NOTE: If you have a network card
installed, remove it temporarily before
installing the PostScript option.
3.
Loosen the access panel screw.
4.
Remove the access panel and locate
the PostScript connector (1).
5.
Install the PostScript card:
a.
Hold the card (
make sure PS is
on the label
) so that the
notch
(2) is on the bottom right
corner.
b.
Position the card into the
connector.
c.
Press down on the card until it
snaps into place and the gold
contacts are fully inserted in
the connector.
6.
Install the memory chip:
Insert the card with the notch
towards the front of the printer.
Press down on the card until it
snaps into place and the gold
contacts are fully inserted in the
connector.
7.
Check to make sure that both
cards are fully inserted and
installed correctly.
8
. Replace the access panel:
a.
Align the panel tabs at bottom.
b.
Swing the panel up and in place.
c.
Tighten the screw.
9. Verify Installation
Print a Menu Map:
a.
Press the
Menu
button one or
more times until INFO.MENU
appears on the display.
b.
Press SELECT twice. The
MenuMap prints.
c.
PSE Program version and Total
Memory Size 32 MB appears
in the header, and PRINT PSE
FONT in the Information
Menu. If not, check to be sure
that the cards are installed
correctly.
58369502
(
Continued on back
)
Your printer is factory set to AUTO
EMULATION (AUTO appears on
the printer display). In this setting
the printer will sample data and
automatically switch between
PostScript emulation and the other
emulations. If the printer is not set to
AUTO EMULATION, see the
User’s Guide for instructions to set
it in the printer Menu.