Oki LE810DT LE810DT User Guide (English)

Oki LE810DT Manual

Get Oki LE810DT PDF manuals and user guides View all Oki LE810DT manuals
Add to My Manuals
Save this manual to your list of manuals

Oki LE810DT manual content summary:

  • Oki LE810DT | LE810DT User Guide (English) - Page 1
    RLTE382120DT User's Guide 59320201 my.okidata.com
  • Oki LE810DT | LE810DT User Guide (English) - Page 2
    or completeness of the information contained herein. The most up-to-date drivers and manuals are available from the web site: http://www.okiprintingsolutions.com Trademark Information Oki is a trademark of Oki Electric Industry Company Ltd. Apple, Macintosh and Mac OS are registered trademarks
  • Oki LE810DT | LE810DT User Guide (English) - Page 3
    This Manual 4 General Printer Description 5 Printer Components 6 Operator Panel 7 Installation 8 Parts Identification 8 Printer 43 Hex Dump Mode 43 Troubleshooting 44 Test Label Printing 44 Sample Test Print Label 45 Maintenance 46 Cleaning the Printer 46 Removing Debris 46 Cleaning
  • Oki LE810DT | LE810DT User Guide (English) - Page 4
    Introduction About This Manual This manual uses special information boxes. Examples of these boxes and the type of information provided in each, are below. Warning! damage if unheeded. Note Provides helpful hints to assist in performing the tasks at hand. LE810DT User's Guide 4 Introduction
  • Oki LE810DT | LE810DT User Guide (English) - Page 5
    comes in several configurations which can differ by • Connection ports on the back of the printer • Default print mode • Internal path for print media Note The appearance of your printer may differ somewhat from the illustrations in this manual, depending on the model you purchased. LE810DT User
  • Oki LE810DT | LE810DT User Guide (English) - Page 6
    Printer Components 1 Operator Panel 2 Print Assembly 3 Platen Roller 4 Dispenser Latch 5 Print Head Latch 6 Rewinder Shaft (only present on some models) 7 External Media Slot 8 Media Holder LE810DT User's Guide 6 Introduction
  • Oki LE810DT | LE810DT User Guide (English) - Page 7
    when receiving data or the buffer is near full. - Illuminates or blinks red when detecting a printer error. 3 manual. 4 FEED button - Press to advance the label media. - Press to select menu options. - Press top initiate other special functions as indicated later in this manual. LE810DT User's Guide
  • Oki LE810DT | LE810DT User Guide (English) - Page 8
    Parts Identification 1 CD-ROM 2 Power Cable 3 USB Cable (included only on models equipped with a USB port) 4 Printer (front view) Printer Installation Site Location • Place the printer on a solid flat surface, away from hazardous materials. • Make sure it is within operational distance of the host
  • Oki LE810DT | LE810DT User Guide (English) - Page 9
    Connection USB / RS232C / IEEE Models 1. Locate the interface connection ports on the back of the printer. 1: USB 2: Serial (RS-232C) 3: IEEE Parallel 2. Connect the appropriate cable to the interface port, then connect it to the computer. USB RS232C IEEE LE810DT User's Guide 9 Installation
  • Oki LE810DT | LE810DT User Guide (English) - Page 10
    5 Ethernet cable (not supplied) into the Ethernet port on the printer and then into the computer. USB Only Model 1. Locate the USB port on the back of the printer. 2. Plug the USB cable supplied with the printer into the USB port on the printer, then into the USB port on the computer. USB LE810DT
  • Oki LE810DT | LE810DT User Guide (English) - Page 11
    printer on. 3. Set the interface option in the configuration menus of the operator panel. Refer to the Configuration unit of this manual to configure the printer for host computer interfacing. Note Multiple interface options may display in the printer's LCD
  • Oki LE810DT | LE810DT User Guide (English) - Page 12
    . The media edge will also wear a groove in the platen roller affecting print quality. Both roll-type and fanfold media can be used with the printer. To use fanfold media, you may need to remove the access plate on the back of the
  • Oki LE810DT | LE810DT User Guide (English) - Page 13
    and wrapped around the rewinder shaft (2). The self-adhesive label (3) without its liner moves out the front of the printer for pickup and direct application. The printer will not print another label until the printed label is removed. 1. Lift up the Top Access Cover. LE810DT User's Guide 13
  • Oki LE810DT | LE810DT User Guide (English) - Page 14
    2. Open the printer front door: push down on the green dispenser latch (1) to release the door, then swing it open (2). 3. Open the Print Head Assembly by rotating the Head Latch (1) counter clockwise. LE810DT User's Guide 14
  • Oki LE810DT | LE810DT User Guide (English) - Page 15
    will go, then angle the label roll over it and push the roll back against the printer housing. Push the Media Support Guide back in until it fits snugly against the media roll (2). 5. Locate the metal Outside Media Guide (1) under the print path and slide it toward you as far as it will go
  • Oki LE810DT | LE810DT User Guide (English) - Page 16
    of the Outside Media Guide (1) to move the top out of the way while you are loading the media. 7. Slide the media into the print path, making sure it goes under the Media Hold-Down (1) and under the Sensor Assembly (2) Push it against the back of the printer. Attention! If the media
  • Oki LE810DT | LE810DT User Guide (English) - Page 17
    finer) until the sensor error is cleared. After the error is cleared, retighten the Sensor Adjust Knob. 9. Pull out the bottom of the Outside Media Guide so that it is upright, then push the guide inward until it barely contacts the outside edge of the media. LE810DT User
  • Oki LE810DT | LE810DT User Guide (English) - Page 18
    from that section. Feed the end of the liner back into the bottom of the printer, under the Backing Drive Roller (1). 11.Pull out the green tab (1) on the (3) on the Take-Up Spindle. Pull the liner through the bottom of the printer and pass the end under the two prongs, then use the green tab to
  • Oki LE810DT | LE810DT User Guide (English) - Page 19
    12.Swing the Head Latch back down to close the print head, then latch it in place. 13.Close the front door and lower the top access cover into place. b Attention! These covers have interlock switches and the printer will not operate if either is open. LE810DT User's Guide 19
  • Oki LE810DT | LE810DT User Guide (English) - Page 20
    Roll-Type, Front Exit with Liner Attached 1. Lift up the Top Access Cover. LE810DT User's Guide 20
  • Oki LE810DT | LE810DT User Guide (English) - Page 21
    2. Open the printer front door: push down on the green dispenser latch (1) to release the door, then swing it open (2). 3. Open the Print Head Assembly by rotating the Head Latch (1) counter clockwise. LE810DT User's Guide 21
  • Oki LE810DT | LE810DT User Guide (English) - Page 22
    will go, then angle the label roll over it and push the roll back against the printer housing. Push the Media Support Guide back in until it fits snugly against the media roll (2). 5. Locate the metal Outside Media Guide (1) under the print path and slide it toward you as far as it will go
  • Oki LE810DT | LE810DT User Guide (English) - Page 23
    of the Outside Media Guide (1) to move the top out of the way while you are loading the media. 7. Slide the media into the print path, making sure it goes under the Media Hold-Down (1) and under the Sensor Assembly (2) Push it against the back of the printer. Attention! If the media
  • Oki LE810DT | LE810DT User Guide (English) - Page 24
    ) until the sensor error is cleared. After the error is cleared, retighten the green Sensor Adjust Knob. 9. Pull out the bottom of the Outside Media Guide so that it is upright, then push the guide inward until it barely contacts the outside edge of the media. LE810DT User
  • Oki LE810DT | LE810DT User Guide (English) - Page 25
    10.Swing the Head Latch back down to close the print head, then latch it in place. 11.Close the front door and lower the top access cover into place. b Attention! These covers have interlock switches and the printer will not operate if either is open. LE810DT User's Guide 25
  • Oki LE810DT | LE810DT User Guide (English) - Page 26
    Fanfold Type 1. Lift up the Top Access Cover. LE810DT User's Guide 26
  • Oki LE810DT | LE810DT User Guide (English) - Page 27
    the back plate covering the access hole. a. Press on the pin holders (1) inside the printer at either end of the bracket until the pins extend from the outer housing. b Carefully plate. c Remove the plate from the printer. Save it with the pins: you will need them should you ever decide to
  • Oki LE810DT | LE810DT User Guide (English) - Page 28
    3. Place the stack of fanfold media behind the printer and feed the first label in through the opening. MEDIA MEDIA MEDIA MEDIA MEDIA MEDIA MEDIA 4. Locate the metal Outside Media Guide (1) under the print path and slide it toward you as far as it will go. LE810DT User's Guide 28
  • Oki LE810DT | LE810DT User Guide (English) - Page 29
    of the Outside Media Guide (1) to move the top out of the way while you are loading the media. 6. Slide the media into the print path, making sure it goes under the Media Hold-Down (1) and under the Sensor Assembly (2) Push it against the back of the printer. Attention! If the media
  • Oki LE810DT | LE810DT User Guide (English) - Page 30
    ) until the sensor error is cleared. After the error is cleared, retighten the green Sensor Adjust Knob. 8. Pull out the bottom of the Outside Media Guide so that it is upright, then push the guide inward until it barely contacts the outside edge of the media. LE810DT User
  • Oki LE810DT | LE810DT User Guide (English) - Page 31
    9. Swing the Head Latch back down to close the print head, then latch it in place. 10.Close the front door and lower the top access cover into place. b Attention! These covers have interlock switches and the printer will not operate if either is open. LE810DT User's Guide 31
  • Oki LE810DT | LE810DT User Guide (English) - Page 32
    the printer. • Once the printed label has been removed from the printer, the with the label as it exits the printer. • The media remains in position for printer automatically peels the liner from the printed label as it exits the printer. • Once the printed label has been removed from the printer
  • Oki LE810DT | LE810DT User Guide (English) - Page 33
    software commands. In the case of conflict between external software commands and control panel settings, the printer will always use the last valid setting (the default is software commands). See the Menu LINE NO FEED YES FEED TO TEST PRINT MENU LE810DT User's Guide 33 Printer Configuration
  • Oki LE810DT | LE810DT User Guide (English) - Page 34
    / DD HH : MM LINE FEED LINE + POWER Toggles Service Mode Scrolls options Scrolls options Scrolls options ADVANCED MODE LINE FEED Scrolls options Scrolls options Scrolls options Scrolls options DATA BIT SELECT 8BIT 7BIT LINE FEED PARITY SELECT User's Guide 34 Printer Configuration
  • Oki LE810DT | LE810DT User Guide (English) - Page 35
    SERVICE MODE FEED LINE COUNTERS MODE LINE FEED COUNTERS HD DSP CUT LIFE LINE DSP FEED DISPENSE COUNTER X.XM FEED DSP COUNT CLEAR YES NO LINE FEED CUT FEED CUT COUNTER X FEED CUT COUNT CLEAR YES NO LINE FEED LIFE FEED LIFE COUNTER X.XM FEED LE810DT User's Guide 35 Printer
  • Oki LE810DT | LE810DT User Guide (English) - Page 36
    test label. Test labels are designed to identify failures in configuration, adjustments problems, and mechanical defects. FEED + POWER Scrolls options TEST PRINT MODE CONFIGURATION BARCODE YES FEED ONLINE MODE [Z] QTY: XXXXXX Scrolls options LE810DT User's Guide 36 Printer Configuration
  • Oki LE810DT | LE810DT User Guide (English) - Page 37
    and enter the required options. LINE + FEED + POWER Scrolls options DEFAULT SETTING YES NO LINE Yes FEED No FEED Printer returned to default settings DEFAULT SETTING COMPLETED Power printer off and then on again to exit. No action, no change LE810DT User's Guide 37 Printer Configuration
  • Oki LE810DT | LE810DT User Guide (English) - Page 38
    the second column contains the data in hexadecimal format, and the right column contains the same data in ASCII format. Send ~ESC+HX command ONLINE [Z] QTY: XXXXXX Printer receives data Printer begins Hex Dump printing Power printer off , to exit LE810DT User's Guide 38 Printer Configuration
  • Oki LE810DT | LE810DT User Guide (English) - Page 39
    deleting data in buffer. Provides the specific sequence of events required by the operator, the printer, and the printer's software for a test label to be printed. Select YES to enter User Test Print menu while select NO will advance to Online mode. LE810DT User's Guide 39 Printer Configuration
  • Oki LE810DT | LE810DT User Guide (English) - Page 40
    line feed (LF) commands in the data stream - including graphics and 2D barcodes. The calendar is an optional feature that allows the date and time to be manually set using the operator panel or through is installed, this menu will not be displayed. LE810DT User's Guide 40 Printer Configuration
  • Oki LE810DT | LE810DT User Guide (English) - Page 41
    SERVICE MODE Second transitional menu screen to access the Counters Mode. COUNTERS MODE Is the first menu screen of the Counters Mode. The Counters Mode allows the printers the length of media since printer setup. HEAD COUNTER CLEAR Resets the print head counter to zero. YES NO LE810DT User
  • Oki LE810DT | LE810DT User Guide (English) - Page 42
    : The printer's configuration settings. • BARCODE: The printer's installed barcodes . If YES is selected, the printer will goes back to TEST PRINT by the operator, the printer, and the printer's software for a test advance to Online mode. Displays the printer's operational status. The ONLINE status
  • Oki LE810DT | LE810DT User Guide (English) - Page 43
    . If YES is selected, resetting will immediately begin. Reboot the printer to return to normal operation. Is an informational screen only indicating that printer is online and waiting to print HEX QTY: XXXXXX interpretation of data received by the print buffer. LE810DT User's Guide 43 Printer
  • Oki LE810DT | LE810DT User Guide (English) - Page 44
    Troubleshooting Test Label Printing The test label is designed to assist in the identification of print problems. The actual content of the test label depends on the type of test label printed. To print a test label: 1. To enter the Test Print mode, turn off the printer, then press and hold the FEED
  • Oki LE810DT | LE810DT User Guide (English) - Page 45
    Sample Test Print Label Note The only print problem that the following sample test label does not display is fading of print image from one side of speed and darkness. 4 Compare this scale on either side to ensure the print is evenly spaced vertically. LE810DT User's Guide 45 Troubleshooting
  • Oki LE810DT | LE810DT User Guide (English) - Page 46
    personal injury. Cleaning of the printer is a necessary maintenance activity to ensure print quality and longer printer life. There are two basic Use a soft cloth and/or a pneumatic blower to remove debris from the printer. This process should be performed prior to the removal of residue. Caution If
  • Oki LE810DT | LE810DT User Guide (English) - Page 47
    Cleaning the Print Head and Platen Attention! The print head should be cleaned after every other label roll is loaded. 1. Turn the printer off and remove the power cable. 2. Open the Top Access Cover. LE810DT User's Guide 47 Maintenance
  • Oki LE810DT | LE810DT User Guide (English) - Page 48
    the platen to clean all of its surface. 9. Allow the roller to dry, then reload the print media and close the top cover. Cleaning the Printer Housing Use a soft lint-free cloth dampened with a bit of water to wipe the
  • Oki LE810DT | LE810DT User Guide (English) - Page 49
    Non-Condensing 30 to 80% RH Non-Condensing CPU Flash ROM Receive Buffer 32 Bit RISC 2 Megabytes 2.95 Megabytes maximum, 2 Megabytes near full LE810DT User's Guide 49 Specifications
  • Oki LE810DT | LE810DT User Guide (English) - Page 50
    (104 mm) Maximum Print Length 15.75 Inches (400 mm) Sensing Specifications Gap Reflective I-Mark Media Out Cover Open Adjustable Adjustable Constant Constant LE810DT User's Guide 50 Specifications
  • Oki LE810DT | LE810DT User Guide (English) - Page 51
    ) Maximum: 8.6 inches (218 mm) 3.0 Inches (76.2 mm) Face Inward Maximum: 3.94 Inches (100 mm) Commands Standard Non-Standard • ZEBRA emulation and ZPL command • SATO Barcode Printer Language (SBPL) • Intelligent Command N/A LE810DT User's Guide 51 Specifications
  • Oki LE810DT | LE810DT User Guide (English) - Page 52
    up to 12 x in either the X or Y coordinates. Character Pitch Control Line Space Control Journal Print Facility 0, 90, 180, and 270 Degree Rotation LE810DT User's Guide 52 Specifications
  • Oki LE810DT | LE810DT User Guide (English) - Page 53
    Bookland • NW-7 • MSI • POSTNET • UCC/EAN 128 • NW-7 (Codabar) Two Dimensional • QR Code • Data Matrix • Maxi Code • PDF417 • Synthetic Symbol Ratios 1:2, 1:3, 2:5, User definable bar widths Bar Height 4 to 999 high-speed editing of complex formats LE810DT User's Guide 53 Specifications
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
User’s Guide
59320201
my.okidata.com
RT322
LE810DT