Oki Pro6410 NeonColor Users Guide - Page 62

Maintenance

Get Oki Pro6410 NeonColor PDF manuals and user guides View all Oki Pro6410 NeonColor manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

MAINTENANCE REPLACING CONSUMABLE ITEMS Only use genuine original consumables to ensure the best quality and performance from your hardware. Non original products may adversely affect your printer's performance and invalidate your warranty. PRINT CARTRIDGE REPLACEMENT NOTE When the LCD display indicates Print Cartridge Near Life, or if print appears faded, first open the top cover and try tapping the cartridge a few times to evenly distribute the toner powder. This will enable you to obtain the best "yield" from your Print Cartridge. CAUTION! To avoid toner wastage and possible toner sensor errors, do not change the Print Cartridge(s) until "Print Cartridge Life" is displayed. The toner used in this printer is a very fine dry powder. It is contained in four cartridges: one each for white, magenta, yellow and cyan. Have a sheet of paper handy so that you have somewhere to place the used cartridge while you install the new one. Dispose of the old cartridge responsibly, inside the pack that the new one came in. Follow any regulations, recommendations, etc., which may be in force concerning waste recycling. If you do spill any toner powder, lightly brush it off. If this is not enough, use a cool, damp cloth to remove any residue. Do not use hot water, and never use solvents of any kind. They will make stains permanent. WARNING! If you inhale any toner or get it in your eyes, drink a little water or bathe your eyes liberally in cold water. Seek medical attention immediately. 1. Press the cover release and open the printer's top cover fully. WARNING If the printer has been powered on, the fuser will be hot. This area is clearly labelled. Do not touch. Maintenance > 62

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
Maintenance > 62
M
AINTENANCE
R
EPLACING
CONSUMABLE
ITEMS
Only use genuine original consumables to ensure the best quality and
performance from your hardware. Non original products may adversely affect
your printer's performance and invalidate your warranty.
P
RINT
CARTRIDGE
REPLACEMENT
The toner used in this printer is a very fine dry powder. It is contained in four cartridges:
one each for white, magenta, yellow and cyan.
Have a sheet of paper handy so that you have somewhere to place the used cartridge while
you install the new one.
Dispose of the old cartridge responsibly, inside the pack that the new one came in. Follow
any regulations, recommendations, etc., which may be in force concerning waste recycling.
If you do spill any toner powder, lightly brush it off. If this is not enough, use a cool, damp
cloth to remove any residue.
Do not use hot water, and never use solvents of any kind. They will make stains permanent.
1.
Press the cover release and open the printer’s top cover fully.
NOTE
When the LCD display indicates Print Cartridge Near Life, or if print appears
faded, first open the top cover and try tapping the cartridge a few times to
evenly distribute the toner powder. This will enable you to obtain the best
“yield” from your Print Cartridge.
CAUTION!
To avoid toner wastage and possible toner sensor errors, do not
change the Print Cartridge(s) until “Print Cartridge Life” is
displayed.
WARNING!
If you inhale any toner or get it in your eyes, drink a little water or
bathe your eyes liberally in cold water. Seek medical attention
immediately.
WARNING
If the printer has been powered on, the fuser will be hot. This area
is clearly labelled. Do not touch.