Onkyo A-9130 User Manual English etc. - Page 14

Speaker impedance settings

Get Onkyo A-9130 PDF manuals and user guides View all Onkyo A-9130 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Speaker impedance settings 1 Preparations / // SETUP Depending on the speakers you connect, you may need to 2 change the speaker impedance setting on this unit. Refer to the page describing speaker connection (p8) and do the following procedures if the change is required. 1. Press SETUP on the remote controller. 0 If this unit is set to be used as a power amplifier, the SETUP button will not work. Check the setting. (p19) 2. Press D/C on the remote controller several times so that input source indicators on the unit, such as "LINE 1" and "LINE 2", start blinking. (BLINKING) 0 The indicators blink and the current setting is displayed. 3 3. Press B/A on the remote controller to change the setting. - 4 ≠: "LINE 1" and "LINE 2" indicators are blinking - 8 ≠ (default value): "LINE 1", "LINE 2", "LINE 3" and "LINE 4" indicators are blinking 4. To exit the settings, press SETUP. 0 The setting mode ends after 5 seconds elapse with no operations performed. 4Ω 8Ω 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
14
Preparations
Depending on the speakers you connect, you may need to
change the speaker impedance setting on this unit. Refer to
the page describing speaker connection (
p8) and do the
following procedures if the change is required.
1. Press SETUP on the remote controller.
0
If this unit is set to be used as a power amplifier, the
SETUP button will not work. Check the setting. (
p19)
2. Press
D
/
C
on the remote controller several times so
that input source indicators on the unit, such as "LINE 1"
and "LINE 2", start blinking.
0
The indicators blink and the current setting is
displayed.
3. Press
B
/
A
on the remote controller to change the
setting.
- 4
≠
: "LINE 1" and "LINE 2" indicators are blinking
- 8
≠
(default value): "LINE 1", "LINE 2", "LINE 3" and
"LINE 4" indicators are blinking
4. To exit the settings, press SETUP.
0
The setting mode ends after 5 seconds elapse with no
operations performed.
Speaker impedance settings
8Ω
4Ω
3
1
2
SETUP
/
/
/
(BLINKING)