Onkyo TX-RZ810 User Manual - Page 26

> Before start > Hookup > Setup > Playback > Part Names 0 If ZONE 2 or ZONE 3 is turned on when the listening mode of the main room is Pure Audio, it will automatically switch to the Direct listening mode. 4. To adjust the volume on the power amplifier in the separate room or the ZONE 2 SPEAKER, adjust with VOL+/- on the remote controller. To control on the main unit, press ZONE 2 or ZONE 3 and adjust with the MASTER VOLUME control within 8 seconds. 0 The information for a connected device can be displayed on the TV screen in a separate room. Press the button while the remote controller is in the mode for controlling ZONE 2. 0 Power consumption in standby mode increases when the multi-zone function is being used. To turn off the function Press Í while in the mode for controlling ZONE 2 or ZONE 3 on the remote controller. Playing in ZONE 2 or ZONE 3 only If you turn the unit to standby during multi-zone playback, the Z2 or Z3 indicator is dimmed and the playback mode is switched to playback in a separate room only. Setting ZONE 2/ZONE 3 to on while this unit is in standby will also switch the playback mode to the same setting. WHOLE HOUSE MODE If you press WHOLE HOUSE MODE while playback is being performed in the main room, the WHOLE HOUSE MODE is turned on, "Z2" and "Z3" on the display light at the same time and the playback sources of all the rooms are switched to the same source at once. 0 The sources that can be played in ZONE 2 can be played in all rooms. 0 This function cannot be used if headphones are connected or audio is output from the speakers of the TV. Settings Settings are required in Initial Setup, "4. Multi Zone Setup" (P21) to use the multi-zone feature. When checking the setting content, refer to the following, press on the remote controller, and check in the Setup menu that is displayed. - When you have connected a TV in the separate room 26 with an HDMI cable, have you selected "Use" in "1. Input /Output Assign" - "TV Out/OSD" - "Zone2 HDMII"? - When you are playing the audio from an AV component in the separate room connected with an HDMI cable, have you selected "Use" in "1. Input /Output Assign" - "TV Out/OSD" - "Zone2 HDMI"? - When you have connected speakers in a separate room with speaker cable, have you selected "Zone 2" (or "Zone 2 A + B") in "2. Speaker" - "Configuration" - "Zone Speaker"? - When you have connected a power amplifier in a separate room with an analog audio cable and you want to control the volume with this unit, have you selected "Variable" in "6. Multi Zone" - "Zone 2" or "Zone 3" - "Output Level"? Others To adjust the sound quality It is possible to enhance or moderate the bass and treble of front speakers. Press TONE on the main unit several times to select the desired setting from "Bass" and "Treble", and turn the TONE dial to adjust. 0 You can also adjust the sound quality of a power amplifier connected in a separate room. After pressing either ZONE 2 or ZONE 3 on the main unit, within 8 seconds press TONE and turn the TONE dial to adjust. 0 This cannot be set if the listening mode is Pure Audio or Direct. Quick Menu By pressing Q on the remote controller during play, you can adjust frequently used settings, such as the sound quality, using on-screen menus. Select the item with the cursors of the remote controller and press ENTER to confirm your selection. To return to the previous screen, press . Quick Menu Tone Level AccuEQ Other Bass Treble BD/DVD "Tone": It is possible to enhance or moderate the bass and treble of front speakers. "Other": Enables you to make a variety of settings. 0 "Speaker Layout": You can switch the output on the surround back speakers and height speakers. 0 "A/V Sync": If the video is behind the audio, you can delay the audio to offset the gap. 0 "Music Optimizer": Improve the quality of compressed audio. 0 "HDMI Out": Allows you to select the HDMI OUT jack to output video signals from "MAIN", "SUB", and "MAIN+SUB". When the unit is operating erratically Try restarting the unit Restarting the unit may help it operate more smoothly. To restart the unit, turn it to standby, and then press Í ON/ STANDBY on the main unit for at least 5 seconds. (The unit's settings will be maintained.) If there is no improvement even after the unit is restarted, try disconnecting and reconnecting the power cords of the unit and connected equipment. Resetting the unit (this resets the unit settings to the default) If restarting the unit doesn't fix the problem, resetting the unit to the status at the time of shipment may solve the problem. If you reset the unit status, your preferences will be reset to the defaults. Note them down before the operation below. 1. While pressing the CBL input selector button on the main unit, press Í ON/STANDBY. 2. "Clear" appears on the display and the unit returns to standby. Do not unplug the power cord until "Clear" disappears from the display. To reset the remote controller, while holding down MODE, press until the remote indicator flash twice (about 3 seconds).