Optoma DV10 MovieTime User Manual
Optoma DV10 MovieTime Manual
 |
View all Optoma DV10 MovieTime manuals
Add to My Manuals
Save this manual to your list of manuals |
Optoma DV10 MovieTime manual content summary:
- Optoma DV10 MovieTime | User Manual - Page 1
Image...20 Adjusting the Projector's Height 20 Adjusting the Projector's Focus 21 Adjusting the Projection Image Size 21 Adjusting the Aspect Ratio of the Image 22 Adjusting the Sloping Image ...23 User Controls Control Panel & Remote Control...24 Using the Remote Control ...25 DVD Projector - Optoma DV10 MovieTime | User Manual - Page 2
...41 System Setup ...42 Language Setup...44 Audio Setup...45 Video Setup ...46 Maintenance Troubleshooting ...47 Image Problems ...47 Intermission Problems...49 LED Problems...49 DVD Player Problems ...50 Sound Problems ...51 Remote Control Problems...51 Replacing the Lamp...52 2 * DVD Projector - Optoma DV10 MovieTime | User Manual - Page 3
operation. ▀■ When the lamp reaches the end of its life, it will burn out and may make a loud "popping" sound. If this occurs, the projector will not turn back on until the lamp module has been replaced. To replace the lamp, follow the procedures listed under "Replacing the Lamp". DVD Projector * 3 - Optoma DV10 MovieTime | User Manual - Page 4
ENGLISH USAGE NOTICE Do: ▀■ Turn off the product before cleaning. ▀■ Use a soft cloth moistened with mild detergent to clean the display housing. ▀■ Disconnect the power plug from AC outlet if the product is dust and dirt. - Near any appliance generating a strong magnetic field. 4 * DVD Projector - Optoma DV10 MovieTime | User Manual - Page 5
-mounting the projector. ▀■ When projector is used in a classroom, adequately supervise students when they are asked to point out something on the screen. ▀■ In order to minimize the lamp power needed to project a visible presentation, use room blinds to reduce ambient light levels. DVD Projector - Optoma DV10 MovieTime | User Manual - Page 6
chip DLPTM projector with builtin DVD player featuring: ▀■ Single 16:9 854x480 chip DLPTM technology ▀■ Uses 7 segment GRBWGRB color wheel ▀■ IR remote control ▀■ User-friendly multilingual on-screen display menu ▀■ Advanced digital keystone correction and high quality full screen image re-scaling - Optoma DV10 MovieTime | User Manual - Page 7
make sure your unit is complete. Projector with lens cap Composite Video Cable 1.8m (For USA and ASIA) VGA Cable 1.8m (For European) Power Cord 1.8m D-Sub to RCA accessories. IR Remote Control AA Battery x 2 Documentation: User's manual Warranty Card Carrying Case DVD Projector * 7 - Optoma DV10 MovieTime | User Manual - Page 8
ENGLISH INTRODUCTION Product Overview Main Unit 1 2 6 3 4 5 7 8 8 * DVD Projector 11 4 1. DVD Cover 2. Focus Ring 3. Zoom Lens 4. IR Receivers 5. Elevator Button 6. Zoom Lever 11 9 10 7. DVD Panel 8. Projector Panel 9. Connection Ports 10. Power Socket 11. Speakers - Optoma DV10 MovieTime | User Manual - Page 9
Projector Panel 1 23 4 ENGLISH 56 7 8 1. Power Button/Power LED 2. Menu 3. Enter 4. Source 5. Tempaterture LED 6. Lamp LED 7. Four Directional Select Keys 8. Resync 1. Stop 2. Play/Pause 3. Backward 4. Forward 5. DVD LED 6. Volume 7. Volume + DVD Panel 1 2 3 4 6 7 5 DVD Projector - Optoma DV10 MovieTime | User Manual - Page 10
Connection Ports 1 23 4 56 78 ENGLISH 9 10 11 1. IR Receiver 2. Service Connector 3. RS232 Input Connector 4. VGA Input Connector (PC Analog signal/SCART RGB/ Audio Output Connector 9. Kensington MicrosaverTM Lock Port 10 Audio Input Connector 11. Power Socket 10 * DVD Projector - Optoma DV10 MovieTime | User Manual - Page 11
ENGLISH INTRODUCTION Remote Control 1 1. Power On/Off 2 3 2. Format 3. Source 4 5 4. Projector Enter Key 6 5. Projector Menu 6. Projector Four Directional 8 Select Keys 7 7. DVD Four Directional Select Keys 9 8. DVD Enter Key 10 9. Setup 11 10. DVD Menu 12 13 11. Display 12. - Optoma DV10 MovieTime | User Manual - Page 12
ENGLISH INSTALLATION Setting up the Projector Connecting the Computer/Notebook 1. Power cord 2. VGA cable 2 1 12 * DVD Projector - Optoma DV10 MovieTime | User Manual - Page 13
ENGLISH INSTALLATION Connecting the Video 1. Power cord 2. Video cable 3. S-Video Cable 4. D-Sub to RCA Adapter 5. RCA Compo- nent Cable for YPbPr 5 The user can install the connection port according to their environment of audio and video equipments or demand. 32 4 1 DVD Projector * 13 - Optoma DV10 MovieTime | User Manual - Page 14
ENGLISH INSTALLATION Connecting the Audio Input 1. Power cord 2. Audio cable (L/R) 1 2 Connecting the Audio Output(External Subwoofer/Stereo System) 2 1. Power cord 2. Audio cable 1 14 * DVD Projector - Optoma DV10 MovieTime | User Manual - Page 15
ENGLISH INSTALLATION 1. Power cord 2. Optical audio cable Connecting the Audio Output(2.1 Channel/5.1 Channel) 2 Optical Digital Audio Input Jack 1 2.1 Channel 5.1 Channel DVD Projector * 15 - Optoma DV10 MovieTime | User Manual - Page 16
menu after the startup screen display. 4. Turn on your source (computer, notebook, video player, etc.), the projector will automatically detect your source. ▀■ Use the "Source" button on the remote control or control panel to select your desired source. 2 Power Button 16 * DVD Projector 1 Lens Cap - Optoma DV10 MovieTime | User Manual - Page 17
are securely connected. The Power LED will flash blue. 3. Turn on the lamp by pressing [Power] button on the control panel. And the Power LED will turn blue. If the DVD player load the disc, you will see a message "Read disc" displayed on the projector's screen. If the DVD player does not load the - Optoma DV10 MovieTime | User Manual - Page 18
digital audio + compressed digital video CD-DA: digital audio HD-CD: digital audio Compressed digital audio Compressed digital audio Digital Photo 18 * DVD Projector Powering Off the Projector 1. Press the [Power] button to turn off the projector lamp, you will see a message "Power off the lamp - Optoma DV10 MovieTime | User Manual - Page 19
, you should contact your local dealer or our service center. ▀■ When the "TEMP" indicator flashes red for about 10 seconds, you will see a message "Fan fail. Lamp will automatically turn off soon." on the on-screen display. Please contact your local dealer or our service center. DVD Projector * 19 - Optoma DV10 MovieTime | User Manual - Page 20
adjustable feet to modify the height of the projector. To raise or lower the image : 1. Locate the elevator foot. Press the -adjustment. 4. Lower the projector so it rests on its foot; adjust as needed. 1 1. Elevator Button 2 2. Elevator Foot 3. Tilt-adjustment 3 3 Foot 20 * DVD Projector - Optoma DV10 MovieTime | User Manual - Page 21
To focus the image, turn the focus ring until you see a clear image. The projector will focus at distances from 3.28 to 32.80 feet (1.0 to 10.0 meters). Focus Ring Zoom Lever Adjusting Projection Image Size Side View (cm) 52.4 52.4 D (cm) 198.53 162.21 D (in) 78.16 63.86 DVD Projector * 21 - Optoma DV10 MovieTime | User Manual - Page 22
ENGLISH INSTALLATION Adjusting the Aspect Ratio of the Image Depending on the type of video source you are viewing, the picture may or may not always look correct or fit on the screen: 4:3 format 16:9 format LBX format 22 * DVD Projector - Optoma DV10 MovieTime | User Manual - Page 23
ENGLISH INSTALLATION Adjusting the Sloping Image If the projector is tilted up or down, the sides of the image on the screen might slope in or out, even though the top and bottom are level. Using the [Keystone] button to adjust the image. Keystone + Keystone - DVD Projector * 23 - Optoma DV10 MovieTime | User Manual - Page 24
functions: with control panel and remote control. Control Panel Remote Control Using the Remote Control Power Format Source Projector Enter Projector Menu Projector Four Directional Select Keys Keystone +/- Volume +/- Press [Power] to turns on the projector's lamp, refer to the "Powering On/Off - Optoma DV10 MovieTime | User Manual - Page 25
to pause playback. Press the [PLAY] button to resume normal playback. Press to activate slow forward or slow rewind. Press to select the desired disc starting time, chapter or title. Repeats playback of the current disc, title, chapter or track. Returns to the previous operation. DVD Projector * 25 - Optoma DV10 MovieTime | User Manual - Page 26
ENGLISH USER CONTROLS Power Power LED Lamp LED Temp LED Using the Projector Panel Press [Power] to turns on the projector's lamp, refer to the "Powering On/Off the Projector" section on page 15~18 for more details. Indicate the projector's status. Indicate the projector's lamp status. Indicate - Optoma DV10 MovieTime | User Manual - Page 27
menus that allow you to make image adjustments and change a variety of settings. The projector will automatically detect the source. How to Operate Projector Menu 1. To open the OSD menu, press [Projector Menu] on the Remote Control or press [Menu] on Control Panel. 2. When OSD is displayed, use - Optoma DV10 MovieTime | User Manual - Page 28
ENGLISH USER CONTROLS Menu Tree for Projector 28 * DVD Projector - Optoma DV10 MovieTime | User Manual - Page 29
ENGLISH USER CONTROLS Language Language Display a multilingual menu. Use and language. Press [Enter] to finalize the selection. to select your preferred DVD Projector * 29 - Optoma DV10 MovieTime | User Manual - Page 30
Memorize user's settings. Brightness Adjust the brightness of the image. ▀■ Press to darken an image. ▀■ Press to lighten an image. Contrast Contrast controls the degree of difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white - Optoma DV10 MovieTime | User Manual - Page 31
ENGLISH USER CONTROLS The "Tint" sub menu is not supported under the digital RGB, component video or analog RGB input sources. Tint Adjust the color balance of red and green. ▀■ Press to increase the amount of green in an image. ▀■ Press to increase the amount of red in an image. Sharpness Adjust - Optoma DV10 MovieTime | User Manual - Page 32
the white peaking control to set the white peaking level of the DMD chip. "1" stands for minimal peaking, and "10" stands for maximum peaking. If you prefer a stronger image, adjust toward the maximum setting. For a smoother, more natural image, adjust toward the minimum setting. Color Temp. Adjust - Optoma DV10 MovieTime | User Manual - Page 33
ENGLISH USER CONTROLS Image AI Image AI is a magician of Image Performance Management for modern Home Use projectors, who can enable the vivid and bright projected image for brighter video content, and on the other hand also reveal the most dark details for dark video content without any - Optoma DV10 MovieTime | User Manual - Page 34
an unstable or flickering image, use this function to correct it. ▀■ Horizontal: Adjusts the horizontal position. ▀■ Vertical: Adjusts the vertical position. Reset Choose "Yes" then "Enter" pressed, the display parameters on this menu will return to their factory default settings. 34 * DVD Projector - Optoma DV10 MovieTime | User Manual - Page 35
USER CONTROLS ENGLISH Display Format ▀■ 4x3: The input source will be scaled to fit the projection-screen. ▀■ 16x9: The standard wide-screen display format of the projector. ▀■ LBX: Enable the viewing of the lettboxed non-anamorphically enhaned movie at full screen width. Part of the original - Optoma DV10 MovieTime | User Manual - Page 36
ENGLISH USER CONTROLS ing error near any edge of the displayable image. Keystone Adjust image distortion caused by tilting projector. (±16 degrees) Reset Choose "Yes" then "Enter" pressed, the display parameters on this menu will return to their factory default settings. 36 * DVD Projector - Optoma DV10 MovieTime | User Manual - Page 37
Choose "ON" to turn on High Altitude mode. Operates the fans at full speed continuously to allow for proper high altitude cooling of the projector. Reset Choose "Yes" then "Enter" pressed, the display parameters on this menu will return to their factory default settings. DVD Projector * 37 - Optoma DV10 MovieTime | User Manual - Page 38
ENGLISH USER CONTROLS Lamp Setting Lamp Hour Displays the cumulative lamp operating time. Lamp Reset Reset the lamp setting only when the new lamp is replaced. Lamp Reminding Choose this function to show or to hide the warning message when the changing lamp message is displayed. The message will - Optoma DV10 MovieTime | User Manual - Page 39
ENGLISH USER CONTROLS How to Operate WMA/MP3/JPEG Program 1. When you place the MP3/JPEG disc, the DVD player will automatically menu. And the marked icon will turn transparency into full color. 4. Use keys to select the desired track. After the selected star, it will begin to flash. 5. Press - Optoma DV10 MovieTime | User Manual - Page 40
ENGLISH USER CONTROLS How to Operate DVD Menu 1. To open the DVD OSD menu, press [Setup] on the Remote Control. 2. When DVD OSD is displayed, use keys to select any item in the "Exit Setup" to confirm, and the screen will return to the main menu. Main menu Sub-menu Item 40 * DVD Projector - Optoma DV10 MovieTime | User Manual - Page 41
ENGLISH USER CONTROLS Menu Tree for DVD DVD Projector * 41 - Optoma DV10 MovieTime | User Manual - Page 42
DVD Projector Password The default setting is "Password is locked ", can't choose "Rating" or revise the password. If need to select "Rating" to press the numerical key and importing the initial password of the one machine: 000000, then press the enter button to confirm. When you need to change the - Optoma DV10 MovieTime | User Manual - Page 43
USER CONTROLS Rating According to the grade of the Videodisc divided and your actual demand to choose the fit rating for yourself. Default Choose "Restore" then "Enter" pressed, the display parameters on all menu will return to their factory default settings. Exit Setup Exit this menu. DVD Projector - Optoma DV10 MovieTime | User Manual - Page 44
ENGLISH USER CONTROLS Language Setup OSD Language Select your preferred language for the on-screen display menu. Audio Lang Select the audio language Subtitle Lang Select the subtitle language Menu Lang Select your preferred language for DVD menu. Exit Setup Exit this menu. 44 * DVD Projector - Optoma DV10 MovieTime | User Manual - Page 45
ENGLISH USER CONTROLS Audio Setup SPDIF Out Choose the appropriate Audio settings for your equipment as it only affect during the playback of DVD discs of the DVD player. ▀■ Off: Turn off the sound. ▀■ RAW: Select this function, when the player is connected to Dolby Digital Decoder. The default is - Optoma DV10 MovieTime | User Manual - Page 46
USER CONTROLS Video Setup Brightness Adjust the brightness of the image. ▀■ Press to darken an image. ▀■ Press to lighten an image. Contrast Contrast controls the degree of difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white - Optoma DV10 MovieTime | User Manual - Page 47
has been securely installed. Please refer to the "Replacing the lamp" section. ■ Ensure that you have removed the lens cap and that the projector is powered on. Partial, scrolling, or incorrectly displayed images: ■ Press [Re-Sync] on the control panel. ■ If using a PC: For Windows 3.x: 1. In the - Optoma DV10 MovieTime | User Manual - Page 48
. Image is out of focus: ■ Make sure the lens cap is removed. ■ Make sure the projection screen is between the required distance 3.3 to 32.8 feet (1.0 to 10.0 meters) from the projector. Image is too small or too large: ■ Adjust the zoom lever on the top of the projector. 48 * DVD Projector - Optoma DV10 MovieTime | User Manual - Page 49
projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp" section on page 50. LED Problems LED lighting message: Message Standby State (Input power cord) Power On/Lamp lighting Power LED (Blue) Flashing Power Off - Optoma DV10 MovieTime | User Manual - Page 50
end of life. ■ "Projector Overheated. Lamp will automatically turn off soon." will be shown when the system temperature is too high. ■ "Fan Fail" will be shown momentarily before shutdown is fan is out of order. DVD Player Problems If a message show an error message: ■ Make sure the disc is inserted - Optoma DV10 MovieTime | User Manual - Page 51
±15°. ■ Make sure there are not any obstructions between the remote con- trol and the projector. Move to within 6 m (20 ft) of the projector. ■ Make sure batteries are inserted correctly. ■ Make sure batteries are exhausted. If so, replace weak batteries in the remote control. DVD Projector * 51 - Optoma DV10 MovieTime | User Manual - Page 52
changing lamp! 3 2 4 Warning: To reduce the risk of personal injury, avoid dropping the lamp module or touching the lamp bulb. If dropped, the bulb may shatter and cause injury. Lamp Replacing Procedure: 1. Turn off the power to the lamp by pressing the power button. 2. Allow the projector
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
 |
 |
DVD Projector
*
1
TABLE OF CONtENtS
E
NGLISH
Usage Notice
Precautions
.............................................................................................................................................
3
Eye Safety
E
E
Warnings
.............................................................................................................................
5
Introduction
Product Features
...................................................................................................................................
6
Package Overview
................................................................................................................................
7
Product Overview
.................................................................................................................................
8
Main Unit
.........................................................................................................................................
8
Projector Panel
...............................................................................................................................
9
DVD Panel
........................................................................................................................................
9
Connection Ports
...........................................................................................................................
10
Remote Control
..............................................................................................................................
11
Installation
Setting up the Projector
.......................................................................................................................
12
Connecting the Computer
...........................................................................................................
r
r
12
Connecting the Video
...................................................................................................................
13
Connecting the Audio Input
........................................................................................................
t
t
14
Connecting the Audio Output-(External Subwoofer/Stereo Systeim)
..............................
14
Connecting the Audio Output-(2.1 Channel/5.1 Channel)
..................................................
15
Powering On/Off the Projector
..........................................................................................................
16
Powering On the Projector
..........................................................................................................
r
r
16
Turn On the DVD Player
...............................................................................................................
r
r
17
Powering Off the Projector
..........................................................................................................
r
r
18
Warning Indicator
.........................................................................................................................
r
r
19
Adjusting the Projected Image
...........................................................................................................
20
Adjusting the Projector’s Height
.................................................................................................
t
t
20
Adjusting the Projector’s Focus
..................................................................................................
21
Adjusting the Projection Image Size
.........................................................................................
21
Adjusting the Aspect Ratio of the Image
..................................................................................
22
Adjusting the Sloping Image
......................................................................................................
23
User Controls
Control Panel & Remote Control
........................................................................................................
24
Using the Remote Control
...........................................................................................................
l
l
25