Optoma EP773 User Manual
Optoma EP773 Manual
 |
View all Optoma EP773 manuals
Add to My Manuals
Save this manual to your list of manuals |
Optoma EP773 manual content summary:
- Optoma EP773 | User Manual - Page 1
Image-I ...21 Image-II ...23 Colour Adjustment...25 Language...25 Management...26 Lamp Setting...29 Appendices 30 Troubleshooting 30 Replacing the Lamp 34 Compatibility Modes 35 RS232 Commands 36 Ceiling Mount Installation 37 Optoma Global Offices 38 Regulation & Safety notices 40 English - Optoma EP773 | User Manual - Page 2
follow all changing instructions. Warning- This product will detect the life of the lamp itself. Please be sure to change the lamp when it shows warning messages. Warning- Reset the "Reset Lamp Hours" function from the On Screen Display "Lamp Setting" menu after replacing the lamp module (refer to - Optoma EP773 | User Manual - Page 3
Usage Notice Do: Turn off the product before cleaning. Use a soft cloth moistened with mild detergent to clean the display housing. Disconnect the power plug from AC outlet if the product is not being used for a long period of time. Don't: Block the slots and openings on the unit provided - Optoma EP773 | User Manual - Page 4
EP773 projector, an Optoma Product. This product is a XGA single chip 0.7" DLP® projector. Outstanding features include: True XGA, 1024 x 768 addressable pixels Texas Instruments Single chip DLP , SXGA+ compression and SVGA, VGA re-sizing Mac compatible DVI support (HDCP compliant) English - Optoma EP773 | User Manual - Page 5
your unit is complete. Contact your dealer immediately if anything is missing. Projector with lens cap Power Cord 1.8m VGA Cable 1.8m S-Video Cable 1.8m Accessory) Documents : User's Guide Quick Start Card Warranty Card Quick Troubleshooting Guide WEEE Card Carrying Case English - Optoma EP773 | User Manual - Page 6
Introduction Product Overview Main Unit 2 1 6 4 5 3 2 7 English 9 8 1. Control Panel 2. Zoom Lever 3. Focus Ring 4. Elevator Button (one on each side) 5. Elevator Foot 6. IR Receivers 7. Power Button 8. Power Socket 9. Connection Ports - Optoma EP773 | User Manual - Page 7
Introduction Control Panel 10 9 8 7 654 321 1. Lamp Indicator LED 2. Temp Indicator LED 3. Power/Standby LED 4. Menu (On/Off) 5. Enter 6. IR Receiver 7. Keystone +/8. Four Directional Select Keys 9. Re-Sync 10. Source Select English - Optoma EP773 | User Manual - Page 8
Introduction Connection Ports 10 9 8 7 6 5 4 3 2 1 11 12 13 14 15 1. DVI-D Input Connector (PC Digital/HDTV/HDCP Input) 2. VGA1-In Connector (PC Analog signal/HDTV/Component Video Input) 3. Audio Input Connector (For DVI-D or VGA1-In) 4. S-Video Input Connector 5. Audio Input Connector (For - Optoma EP773 | User Manual - Page 9
Introduction Remote Control with Mouse Function and Laser Pointer 15 1. Power 2. Re-Sync 3. Keystone Correction 16 1 4. Display Format 5. Mouse 17 2 6. Mouse Right Click 18 3 7. Page Up 19 4 8. Page Down 9. Four Directional Select 5 Keys 10. Enter 11. S-Video Source 12. Composite - Optoma EP773 | User Manual - Page 10
Installation Connecting the Projector Connect the Computer/Notebook 5 RS232 43 2 DVD Player, Set- top Box, RGB HDTV receiver USB 6 S-Video Output Video Output 1 Audio Output (For Active Speakers) Due - Optoma EP773 | User Manual - Page 11
Installation Connect the Video Video Output 3 5 4 2 6 Audio Output (For Active Speakers) 5 7 1 8 3 S-Video Output DVD Player, Set-top Box, HDTV receiver Due to the differ- ence in applications 1...Power Cord for each country, 2 RCA Component Cable for YPbPr some regions may 3 SCART - Optoma EP773 | User Manual - Page 12
. The Power LED will turn red. 3. Turn on the lamp by pressing "Power/Standby" button on the control panel. And the Power LED will turn green. 4. Turn on your source (computer, notebook, video player, etc.). The projector will detect your source automatically within "Management" menu; check that - Optoma EP773 | User Manual - Page 13
shut itself down. When the "LAMP" indicator turns red, it indicates a problem with the lamp. Turn off the projector and disconnect the power cord from the electrical outlet, then contact your local dealer or our service center. See page 38. When the "LAMP" indicator flashes red, it indicates - Optoma EP773 | User Manual - Page 14
Installation Adjusting the Projected Image Adjusting the Projector Image Height The projector is equipped with elevator feet for adjusting the image height. To raise the image: 1. Press the elevator button . 2. Raise the image to the desired height - Optoma EP773 | User Manual - Page 15
You may turn the zoom lever to zoom in or out. To focus the image, rotate the focus ring until the image is clear. The projector will focus at distances from 4.9 to 40.0 feet (1.5 to 12.2 meters). Zoom Lever Focus Ring Adjusting Projection Image Size Diagonal Width 36.9" (93.8cm) 30 - Optoma EP773 | User Manual - Page 16
control the functions: Remote Control and Control Panel. Control Panel Remote Control Using the Control Panel Power Refer to the "Power On/Off the Projector" section on pages 12-13. Source Press "Source" to select an input signal. Menu Turns the menu On or Off. Four Directional Select Keys - Optoma EP773 | User Manual - Page 17
Page Up Page Down Zoom In Zoom Out Four Directional Select Keys Menu Clear Enter Source Lock Adjusts image distortion caused by tilting the projector (±16 degrees). Display the "Display Format" section of the onscreen display menu to select the desired aspect ratio. Aim the remote at the viewing - Optoma EP773 | User Manual - Page 18
User Controls Video S-Video VGA1 VGA2 DVI Choose composite video source. Choose S-video source. Choose primary VGA-In source. Choose secondary VGA-In source or SCART source. Choose DVI-D source. English 18 - Optoma EP773 | User Manual - Page 19
has multilingual On Screen Display menus that allow you to make image adjustments and change a variety of settings. The projector will automatically detect the source. How to Operate 1. To open the OSD menu, press "Menu" on the Remote Control or Control Panel. 2. When OSD is - Optoma EP773 | User Manual - Page 20
User Controls Menu Tree English 20 - Optoma EP773 | User Manual - Page 21
User Controls Image-I Display Mode There are many factory presets optimized for various types of images. Presentation: Good colour and brightness from PC input. Bright: Maximum brightness from PC input. Video: Pleasing video. Cinema: High contrast and colour accuracy. sRGB: Standardised - Optoma EP773 | User Manual - Page 22
Sharpness Adjusts the sharpness of the image. Press the to decrease the sharpness. "Saturation" and "De-interlace" functions are only supported under Video mode. Press the to increase the sharpness. De-interlace This function converts an interlaced video signal into progressive signal. On - Optoma EP773 | User Manual - Page 23
User Controls Image-II "Frequency", "Phase", "Hor. position" and "Ver. position" functions are only supported under Computer mode. Frequency "Frequency" changes the display data frequency to match the frequency of your computer's graphic card. If you experience a vertical flickering bar, - Optoma EP773 | User Manual - Page 24
User Controls Input Signal Display area Picture area Display on Screen Ver. Shift (16:9): Image Position at window mode will also be moved accordingly. Ver. Shift (16:9) Adjust the image position up or down, when you select the aspect ratio of 16:9. Press the to move the image down. Press - Optoma EP773 | User Manual - Page 25
User Controls Colour Adjustment Colour Adjustment Adjust the Red, Green, Blue, Yellow, Cyan and Magenta colors for advanced adjustment of the individual colors. Language Language Choose the multilingual OSD menu. Use the or key to select your preferred language. Press "Enter" to finalize the - Optoma EP773 | User Manual - Page 26
Choose the menu location on the display screen. Projection Front-Desktop The factory default setting. Rear-Desktop When you select this function, the projector reverses the image so you can project from behind a translucent screen. Front-Ceiling When you select this function, the - Optoma EP773 | User Manual - Page 27
Choose "On" to turn on High Altitude mode. Operates the fans at full speed continuously to allow for proper high altitude cooling of the projector. Volume Press to decrease the volume. Press to increase the volume. Treble The treble setting controls the higher frequencies of your audio source - Optoma EP773 | User Manual - Page 28
User Controls Security Security Timer: Can be select the time (month/day/hour) func- tion to set the number of hours the projector can be used. Once the time has elapsed you will be requested to enter your password again. Change Password Use number buttons to select your - Optoma EP773 | User Manual - Page 29
life hour counter after replacing the lamp. Lamp Reminder Choose this function to show or to hide the warning message when the changing lamp message is displayed. The message will appear 30 hours before end of life. STD Mode Choose "On" to dim the projector lamp which will lower power consumption - Optoma EP773 | User Manual - Page 30
Appendices Troubleshooting If you experience trouble with the projector, refer to the following information. If the problem persists, please contact your local reseller or service center, see page 38 for details. English 30 Problem: No image appears on screen Ensure all the cables and power - Optoma EP773 | User Manual - Page 31
-->Display-->Arrangement-->Mirror display If you experience difficulty changing resolutions or your monitor freezes, restart all equipment including the projector. Problem: The screen of the Notebook or PowerBook computer is not displaying a presentation If you are using a Notebook PC: Some - Optoma EP773 | User Manual - Page 32
burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp". Problem: LED lighting message Message Standby State (Input power cord) Warming Normal Mode - Optoma EP773 | User Manual - Page 33
Appendices Problem: Message Reminders Fan fail: Over temperature: Power Off: Replace the lamp: 33 English - Optoma EP773 | User Manual - Page 34
of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped. English 34 Lamp Replacement Procedure: 1. Switch off the power to the projector by pressing the Power/ Standby button. 2. Allow the projector to cool down for at least 30 - Optoma EP773 | User Manual - Page 35
VGA VESA VGA VESA VGA VESA VGA VESA VGA VESA VGA VESA VGA VESA SVGA VESA SVGA VESA SVGA VESA SVGA VESA SVGA VESA XGA VESA XGA VESA XGA VESA XGA * VESA SXGA * VESA SXGA * VESA SXGA+ MAC LC 13" MAC II 13" MAC 16" MAC 19" * MAC MAC G4 i MAC DV * i MAC DV - Optoma EP773 | User Manual - Page 36
Appendices RS232 Commands RS232 Connector 3 VGA-In Connector 2 1 Pin no. 1 2 3 Name TXD RXD GND I/O (From Projector Side OUT IN __ 54321 10 9 8 7 6 15 14 13 12 11 Pin no. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Spec. R(RED)/Cr G(GREEN)/Y B(BLUE)/Cb GND GND GND GND GND DDC 5V GND GND DDC Date - Optoma EP773 | User Manual - Page 37
installation. 2. If you wish to use a third party ceiling mount kit, please ensure the screws used to attached a mount to the projector meet the following specifications: Please note that damage resulting from incorrect installation will invalidate the warranty. Screw type: M3 Maximum screw - Optoma EP773 | User Manual - Page 38
Appendices Optoma Global Offices For service or support please contact your local office. USA 715 Sycamore Drive Milpitas, CA 95035, USA www.optomausa.com Tel : 408-383-3700 Fax : 408-383-3702 Service : [email protected] Canada 5630 Kennedy Road, Mississauga, ON, L4Z 2A9, Canada Tel : 905- - Optoma EP773 | User Manual - Page 39
92517 Boulogne Billancourt, France Servicel : [email protected] Optoma Deutschland Werftstrasse 25 D40549 Düsseldorf, Germany Tel : +49 (0) 211 506 6670 Fax : +49 (0) 211 506 66799 Service : [email protected] Optoma Scandinavia Grev Wedels Plass 2 3015 Drammen Norway - Optoma EP773 | User Manual - Page 40
notices This appendix lists the general notices of your Projector. FCC notice This device has been tested and found to comply with the limits for a Class and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is - Optoma EP773 | User Manual - Page 41
Appendices Operation conditions This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.this device may not cause harmful interference, and 2.this device must accept any interference received, including interference that may cause undesired
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
 |
 |
±
English
Table of Contents
Table of Contents
.........................................................................................
±
Usage Notice
................................................................................................
2
Precautions
...........................................................................................................
2
Introduction
...................................................................................................
4
Product Features
..................................................................................................
4
Package Overview
................................................................................................
5
Product Overview
.................................................................................................
6
Main Unit
........................................................................................................................
6
Control Panel
.................................................................................................................
7
Connection Ports
...........................................................................................................
8
Remote Control with Mouse Function and Laser Pointer
..............................................
9
Installation
..................................................................................................
±0
Connecting the Projector
....................................................................................
10
Connect the Computer/Notebook
................................................................................
10
Connect the Video
.......................................................................................................
11
Powering On/Off the Projector
............................................................................
12
Powering On the Projector
...........................................................................................
12
Powering Off the projector
...........................................................................................
13
Warning Indicator
.........................................................................................................
13
Adjusting the Projected Image
............................................................................
14
Adjusting the Projector Image Height
..........................................................................
14
Adjusting the Projector Zoom / Focus
..........................................................................
15
Adjusting Projected Image Size
...................................................................................
15
User Controls
.............................................................................................
±6
Control Panel & Remote Control
........................................................................
16
On-Screen Display Menus
..................................................................................
19
How to Operate
...........................................................................................................
19
Menu Tree
....................................................................................................................
20
Image-I
........................................................................................................................
21
Image-II
.......................................................................................................................
23
Colour Adjustment
........................................................................................................
25
Language
.....................................................................................................................
25
Management
................................................................................................................
26
Lamp Setting
................................................................................................................
29
Appendices
.................................................................................................
30
Troubleshooting
..................................................................................................
30
Replacing the Lamp
............................................................................................
34
Compatibility Modes
...........................................................................................
35
RS232 Commands
.............................................................................................
36
Ceiling Mount Installation
...................................................................................
37
Optoma Global Offices
.......................................................................................
38
Regulation & Safety notices
...............................................................................
40