Optoma W351 Manual - Page 62

Installing and Cleaning the Filter, Installing the Filter

Get Optoma W351 PDF manuals and user guides View all Optoma W351 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Appendices Installing and Cleaning the Filter Installing the Filter 1. Install two filters. 2. Turn on the projector then press "Menu", go to "OPTIONS -> Optional Filter Settings -> Optional Filter Installed" and select "Yes".  Dust filters are only required/sup- plied in selected regions with ex- cessive dust. A B Cleaning the Filter It is recommended to clean/replace filters every three months or sooner depending upon the environment by following the steps below. 1. Switch off the power to the projector by pressing the " " button. 2. Disconnect the power cord. 3. Remove the filter slowly and carefully. 4. Clean or replace the filter. 5. To install the filter, reverse the previous steps. 6. Reset the filter counter after replacing or cleaning the dust filter. Press "Menu", go to "OPTIONS -> Optional Filter Settings -> Filter Reset" Removing the Filter 1. Remove the filters from the projector. Remove dust (if any). 2. Turn on the projector. 3. Press "Menu", go to "OPTIONS -> Optional Filter Settings -> Optional Filter Installed" and select "No". (Remove when you pull out the dust filter and would not install it again.) 4. Close the OSD. English 62 A B

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
62
English
Appendices
Installing and Cleaning the Filter
Installing the Filter
Install two filters.
1.
Turn on the projector then press “Menu”, go to “OPTIONS ->
2.
Optional Filter Settings -> Optional Filter Installed” and select
“Yes”.
A
B
Cleaning the Filter
It is recommended to clean/replace filters every three months or
sooner depending upon the environment by following the steps below.
Switch off the power to the projector by pressing the “
1.
” button.
Disconnect the power cord.
2.
Remove the filter slowly and carefully.
3.
Clean or replace the filter.
4.
To install the filter, reverse the previous steps.
5.
Reset the filter counter after replacing or cleaning the dust filter.
6.
Press “Menu”, go to
“OPTIONS -> Optional Filter Settings ->
Filter Reset”
Removing the Filter
1. Remove the filters from the projector. Remove dust (if any).
2. Turn on the projector.
3. Press “Menu”, go to “OPTIONS -> Optional Filter Settings ->
Optional Filter Installed” and select “No”. (Remove when you
pull out the dust filter and would not install it again.)
4. Close the OSD.
A
B
Dust filters are
only required/sup
-
plied in selected
regions with ex
-
cessive dust.