Optoma ZH500UST ZU500UST_ZH500UST_UM - Page 15

Powering off the projector, Warning Indicator, Orange. When the POWER/STANDBY LED lights solid

Get Optoma ZH500UST PDF manuals and user guides View all Optoma ZH500UST manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Installation Powering Off the Projector 1. Press the " " button on the remote control or on the control panel to turn off the projector. The following message will be displayed on the screen. Press the " " button again to confirm otherwise the message will disappear after 10 seconds. When you press the " " button for the second time, the fan will start cooling the system and will shut down. 2. The cooling fans continue to operate for about 4 seconds for cooling cycle and the POWER/STANDBY LED will flash Orange. When the POWER/STANDBY LED lights solid Orange, the projector has entered standby mode. If you wish to turn the projector back on, you must wait until the projector has completed the cooling cycle and has entered standby mode. Once in standby mode, simply press " " button to restart the projector. 3. Disconnect the power cord from the electrical outlet and the projector. Warning Indicator When the warning indicators (see below) come on,  Contact the the projector will automatically shutdown: nearest service  "LAMP" LED indicator is lit red and if "POWER/STANDBY" center if the indicator flashes amber. projector displays these symptoms.  "TEMP" LED indicator is lit red, this indicates the projector has overheated. Under normal conditions, the projector can be switched back on.  "TEMP" LED indicator flashes red and if "POWER/STANDBY" indicator flashes amber. Unplug the power cord from the projector, wait for 30 seconds and try again. If the warning indicator light up again, please contact your nearest service center for assistance. 15 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
15
English
Installation
Contact the
nearest service
center if the
projector displays
these symptoms.
Powering Off the Projector
1. Press the “
” button on the remote control or
on the control panel to turn off the projector.
The following message will be displayed on the screen.
Press the “
” button again to confirm otherwise the
message will disappear after 10 seconds. When you press
the “
” button for the second time, the fan will start cooling
the system and will shut down.
2. The cooling fans continue to operate for about 4 seconds
for cooling cycle and the POWER/STANDBY LED will flash
Orange. When the POWER/STANDBY LED lights solid
Orange, the projector has entered standby mode.
If you wish to turn the projector back on, you must wait until
the projector has completed the cooling cycle and has en-
tered standby mode. Once in standby mode, simply press “
” button to restart the projector.
3. Disconnect the power cord from the electrical outlet and the
projector.
Warning Indicator
When the warning indicators (see below) come on,
the projector will automatically shutdown:
“LAMP” LED indicator is lit red and if “POWER/STANDBY”
indicator flashes amber.
“TEMP” LED indicator is lit red, this indicates the projector
has overheated. Under normal conditions, the projector can
be switched back on.
“TEMP” LED indicator flashes red and if “
POWER/STAND-
BY
” indicator flashes amber.
Unplug the power cord from the projector, wait for 30 seconds
and try again. If the warning indicator light up again, please
contact your nearest service center for assistance.