Panasonic 36PSU1U6 Installation Instructions - Page 47

Fig. 5-16, Fig. 5-17, Fig. 5-18, Fig. 5-19, Fig. 5-20, Fig. 5-21, Fig. 5-22

Get Panasonic 36PSU1U6 PDF manuals and user guides View all Panasonic 36PSU1U6 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

When using the signal receiving unit on a wall with the front exposed, choose a wall surface that the signal receiving unit can be mounted on. (1) Insert a flathead screwdriver into the slot on the lower side of the signal receiving unit and pry off the back case. (2) The wire routing at the signal receiving unit comes out of the upper case (thin portion at upper center) so use nippers or a similar tool to cut out a notch beforehand large enough for the remote control cable (option) to pass through as shown in Fig. 5-16. (3) Remove the wire, which is connected prior to shipping, from the connector. (4) Connect the remote control cable (option) to the signal receiving unit connector as shown in Fig. 5-17 after the clamp (supplied) with the unit is installed. (5) After arranging the wiring on the printed circuit board as shown in Fig. 5-18 so that it is contained within the signal receiving unit, attach the back case. At this time, arrange so that the head of the clamp faces the side. (6) Remove the cover plate and install the signal receiving unit using the 2 wood screws. (7) Fasten to the wall using the cord clip (supplied). (8) Reinstall the cover plate. To use the signal receiving unit while mounted on the ceiling, install by using the carrier for ceiling installation supplied with the unit. (1) Remove the cover plate by inserting a flathead screwdriver into the notch in the lower section and prying it off. (2) Cut out a section (3-3/4"×2-1/32") on the ceiling using the paper pattern (supplied) as a guide. (3) Run the wire through the mounting carrier and insert into the installation hole as shown in Fig. 5-20. (4) Fit securely into the ceiling material at sections (A) and (B) as shown in Fig. 5-21. (5) Connect the wire (2-wire core) from the signal receiving unit with the wire from the indoor unit. (See section on how to wire the receiving unit.) as shown in Fig. 5-21. (6) Use the supplied spacers to adjust for a thickness several inches more than the ceiling material and lightly fasten the receiving unit in place with the small screws (M4×1-9/16", 2 pcs.) supplied with the unit. (7) Tighten the machine screws after fitting sections (A) and (B) into the openings, in the gap between the signal receiving unit and ceiling surface as in Fig. 5-22. Do not apply strong force when tightening the screws. Excessive force might warp or damage the cover. When finished, the signal receiving unit should still be able to move slightly when pressed as shown in Fig. 5-22. (8) Reinstall the cover plate. Run the remote con cable through a notch in the upper case. Clamp (Supplied) About 3/32"-1/8" Fig. 5-16 Connector Remote control cord (Option) Fig. 5-17 Remote control cord (Option) Signal receiving unit Clamp ALL• RTPECCSUBT:CRSHUUKNB. NROCURM: MALAIN 123 ADR 456 Fig. 5-18 Wood screws (2) Fig. 5-19 A Fig. 5-20 Fig. 5-22 B Fig. 5-21 47 1BOBTPOJD@1"$J@*OEPPS6OJU@64MF

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
47
When using the signal receiving unit on a wall with
the front exposed, choose a wall surface that the
signal receiving unit can be mounted on.
(1) Insert a flathead screwdriver into the slot on the lower
side of the signal receiving unit and pry off the back
case.
(2) The wire routing at the signal receiving unit comes out
of the upper case (thin portion at upper center) so use
nippers or a similar tool to cut out a notch beforehand
large enough for the remote control cable (option) to
pass through as shown in Fig. 5-16.
(3) Remove the wire, which is connected prior to shipping,
from the connector.
(4) Connect the remote control cable (option) to the signal
receiving unit connector as shown in Fig. 5-17 after the
clamp (supplied) with the unit is installed.
(5) After arranging the wiring on the printed circuit board
as shown in Fig. 5-18 so that it is contained within the
signal receiving unit, attach the back case. At this time,
arrange so that the head of the clamp faces the side.
(6) Remove the cover plate and install the signal receiving
unit using the 2 wood screws.
(7) Fasten to the wall using the cord clip (supplied).
(8) Reinstall the cover plate.
To use the signal receiving unit while mounted on the
ceiling, install by using the carrier for ceiling installation
supplied with the unit.
(1) Remove the cover plate by inserting a flathead
screwdriver into the notch in the lower section and
prying it off.
(2) Cut out a section (3-3/4"×2-1/32") on the ceiling using
the paper pattern (supplied) as a guide.
(3) Run the wire through the mounting carrier and insert
into the installation hole as shown in Fig. 5-20.
(4) Fit securely into the ceiling material at sections (A)
and (B) as shown in Fig. 5-21.
(5) Connect the wire (2-wire core) from the signal
receiving unit with the wire from the indoor unit. (See
section on how to wire the receiving unit.) as shown in
Fig. 5-21.
(6) Use the supplied spacers to adjust for a thickness
several inches more than the ceiling material and
lightly fasten the receiving unit in place with the small
screws (M4×1-9/16", 2 pcs.) supplied with the unit.
(7) Tighten the machine screws after fitting sections (A)
and (B) into the openings, in the gap between the
signal receiving unit and ceiling surface as in Fig. 5-22.
Do not apply strong force when tightening the screws.
Excessive force might warp or damage the cover.
When finished, the signal receiving unit should still be
able to move slightly when pressed as shown in Fig.
5-22.
(8) Reinstall the cover plate.
Run the remote con
cable through a notch
in the upper case.
Clamp (Supplied)
About 3/32"-1/8"
Connector
Remote control cord
(Option)
Remote control cord (Option)
Clamp
Signal receiving unit
Wood screws (2)
1
2
3
4
R
D
A
6
5
•
L
L
A
B
U
S
:
U
C
R
N
I
A
M
:
U
C
R
L
A
M
R
O
N
.
K
H
C
B
C
P
N
U
R
T
S
E
T
B
A
Fig. 5-16
Fig. 5-17
Fig. 5-18
Fig. 5-19
Fig. 5-20
Fig. 5-21
Fig. 5-22
Panasonic_PAC-i_IndoorUnit_US-le47 47
Panasonic_PAC-i_IndoorUnit_US-le47
47
2011/11/02 15:17:35
2011/11/02
15:17:35