Panasonic AW-PH650NK1 System Camera and Switcher Product Lineup Catalog - Page 45

Studio Camera System As of April, 2017 SD card recording SD card recording MPEG-4 AVC file standard compliant (.MP4) Video compression format MPEG-4 AVC/H.264 High Profile Audio compression format AAC-LC (48 kHz, 16 bit, 2 ch, 128 kbps) Recording format /Bit rate 59.94 Hz 3840 x 2160/29.97p (Up to 72 Mbps), 1920 x 1080/59.94p (Up to 28 Mbps), 1920 x 1080/29.97p (Average 15 Mbps/ Average 10 Mbps/Average 6 Mbps), 1280 x 720/59.94p (Average 15 Mbps), 1280 x 720/29.97p (Average 8 Mbps/ Average 4 Mbps/Average 2 Mbps) 50 Hz 3840 x 2160/25p(Up to 72 Mbps), 1920 x 1080/50p(Up to 28 Mbps), 1920 x 1080/25p(Average 15 Mbps/ Average 10 Mbps/Average 6 Mbps), 1280 x 720/50p(Average 15 Mbps), 1280 x 720/25p(Average 8 Mbps/ Average 4 Mbps/Average 2 Mbps) Network Transfer modes JPEG H.264 1920 x 1080, 1280 x 720, 640 x 360, 320 x 180, 59.94 Hz (30fps/15fps/5fps)*8, 50 Hz (25fps/12.5fps/5fps)*8 3840 x 2160, 1920 x 1080, 1280 x 720, 640 x 360, 320 x 180, 59.94 Hz (60fps*9/30fps/15fps/5fps)*8, 50 Hz (50fps*9/25fps/12.5fps/5fps)*8 IPv4 Supported protocol IPv6 i-OS, Android support TCP/IP, UDP/IP, HTTP, HTTPS, RTSP, RTP, RTP/RTCP, FTP, DHCP, DNS, NTP, IGMP, UPnP, ICMP, ARP, RTSPoverTCP, RTSPoverHTTP, SSL(TLS), MultiCast/UniCast TCP/IP, UDP/IP, HTTP, HTTPS, RTSP, RTP, RTP/RTCP, FTP, DHCPv6, DNS,NTP, ICMPv6(MLD), RTSPoverTCP, RTSPoverHTTP, SSL(TLS), MultiCast/UniCast JPEG image display Standard Accessories Mount bracket for installation surface (Hanging*10 / Desktop): 1, Drop-prevention wire (already attached to the unit): 1, Bracket mounting screws (bind-head) M4 x 10 mm: 4, Main unit mounting screw (with flat washer, spring washer) M3 x 6 mm: 1, Power cable (1.5 m [4.92 ft]): 1, AC adaptor: 1, CD-ROM: 1 * 1: It may be necessary to upgrade the version of the controller so that the controller will support the unit. * 2: During Auto, 6 dB to 48 dB (6 dB step) are available for AGC Max Gain setting. * 3: During Auto, 0 dB, 6 dB, 12 dB and 18 dB are available for Auto F.Mix Max Gain setting. * 4: "Auto" is available when "Scene" setting is "Full Auto". * 5: To ensure safety, the unit must be secured using the mount bracket supplied. * 6: Depending on the pan or tilt position, the camera may be reflected in the image. * 7: Use of an STP (shielded twisted pair) cable is recommended. *8: The frame rate may be lower than the setting depending on the operating conditions. * 9: When the image resolution is "3840x2160", "640x360" or"320x180", 60fps or 50fps cannot be selected for the frame rate. *10: To ensure more safety, AW-UE70W/K can be secured by using the direct ceiling mount bracket (WV-Q105A). *For informations on "Output Signal Format", see page 38. Dimensions Unit: mm(inches) Rear View (Front) (Side) Remote Camera System 3 (1/8) 48 (1-57/64) 129 (5-5/64) 183 (7-13/64) Live Switcher 160 (6-5/16) 80 (3-5/32) 77 (3-1/32) 166 (6-17/32) 179 (7-3/64) Bottom View Unit: mm(inches) Ceiling Installation View ( *) 4(*)64(61(-1-1133//116)6) 78(3-1/16) 65(2-9/16) 80(3-5/32) 77(3-1/32) 90(3-17/32) 9 9(3-29/32) 290(11-7/16) or more (Space for the wires) Through-hole for cable ø 4 0 (ø 1-9/16)(reference) Hole for mounting the main unit mounting screw Hook for mounting the drop-prevention wire Unit mounting area Mount bracket (*)Holes for mounting the mount bracket: ø 4.5 x 4 130 (5 -1/8) (Space for the wires from the rear panel) 66 (2-19/32) Optimal for both hanging and desktop installation. The mounting bracket and drop-preventation wire are standard accessories. Ceiling and desktop installation are both possible. Mount the bracket onto the installation surface and then put and turn the main unit on the bracket to be installed. Hole for checking the positioning On the mount bracket: Protrusions (x3) used for inserting the camera Dropprevention wire Approx. 15° On the camera main unit: Holes (x3) used to insert the bottom panel Status display lamp Hole for checking the positioning (*)83.5 (3-9/32) 156 (6-1/8) 160 (6-5/16) Hole for installing the WV-Q105A direct ceiling mount bracket The mounting bracket for discontinued AW-HE50 and AW-HE60 and [ø 60 (ø 2-3/8)] current AW-HE40 series can also be used. The front side of the unit * Wiring, mounting, and removal must be done by a qualified technician. 45 To ensure safety, consult with the dealer from whom you purchased the system. *For "Terminal Pin Configuration", see page 47.