Panasonic CF-73N3LTSKM Notebook Computer - Page 31
Caution
UPC - 092281840086
View all Panasonic CF-73N3LTSKM manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 31 highlights
10 At the confirmation message, press Y . The operation of reinstallation for the hard disk starts automatically. (The operations take about 15 minutes.) CAUTION Do not interrupt the reinstallation procedure before completion, for example by turning off the computer or pressing Ctrl + Alt + Del , as this may prevent Windows from starting up, or may cause data to be lost so that the reinstallation procedure cannot be executed. After the reinstallation procedure completes, this screen should appear. [Recovery] is complete. Windows(R) XP Professional install wizard will start after reboot. P--le--a-s-e--re--m-o--v-e-t-h-e--P-r-o-d-u--c-t-R-e--c-o-v-e-r-y-D--V--D---R-O--M--,-a-n-d--t-u-r-n-o--ff-t-h-e--c-o-m--p-u-t-e-r-. 11 Remove the Product Recovery DVD-ROM, and then press any key. The computer will be shut down. 12 Turn on the computer, and press F2 while [Panasonic] boot screen is displayed. The Setup Utility will start up. If the password has been set, enter the Supervisor Password. 13 Press F9 . At the confirmation message, select [Yes] and press Enter . (The Setup Utility settings will return to their default values. Even the security settings with the exception of the password(s) will return to their default values.) 14 Select [Exit] and then select [Save Current Values], then press Enter . At the confirmation message, select [Yes] and press Enter . 15 Turn off the computer by pressing the power switch. NOTE If additional instructions are included with the computer, be sure to read them. It may be necessary to perform additional operations during the following procedures. 16 Perform the first-time use operation ( - page 14 step 10 ). page 12 step 6 17 Run the Setup Utility and change the settings where necessary. You can change the drive letter for the CD/DVD drive or hard disk drive by the following steps. Drive letters can only be changed when two or more partitions have been created on the hard disk drive. The name of the C: drive cannot be changed. We recommend that you make these changes before installing applications. 1 Select [start] - [Control Panel] - [Performance and Maintenance] - [Administrative Tools] - [Computer Management]. 2 Select [Disk Management] from [Storage]. 3 Right click on the partition of the hard disk or the name of the CD drive and select [Change Drive Letter and Paths...]. 4 Select [Change]. 5 Select [Assign the following drive letter] and select the new drive letter, and then select [OK]. 6 At the confirmation message, select [Yes]. If you select [3] in step 9 ( page 30) and execute reinstallation, the drive name for the second partition (data partition) may be switched with that of the SD Memory Card. You can still use the drives after the names have been switched, but you can also return the drive names to their original state using the following procedures. (The following procedure assumes that before reinstallation, the second partition (data partition) was Drive D:, and the SD Memory Card was Drive E:) 1 Disable the drive name for the second partition (data partition). 1 In the menu below, select [Computer Management]. Select [start] - [Control Panel] - [Performance and Maintenance] - [Administrative Tools]. 2 Select [Disk Management]. 3 Right click on the partition for which [E:] is displayed and select [Change Drive Letter and Paths...]. 4 Select [Remove]. 5 At the confirmation message, select [Yes]. 2 Change the SD memory card drive name to [E:]. Use the SD drive name change tool to change the SD Memory Card to the E: drive. ( "SD Memory Card/MultiMedia Card"). 3 Set the drive name for the second partition (data partition) as [D:]. 1 In the menu below, select [Computer Management]. Select [start] - [Control Panel] - [Performance and Maintenance] - [Administrative Tools]. 2 Select [Disk Management]. 3 Right click on the partition for which the drive name is not displayed, and select [Change Drive Letter and Paths...]. 4 Select [Add...], assign [D:] as the drive letter, and select [OK]. Troubleshooting 31