Panasonic PT-44LCX65 Multi Media Display - Page 67

CAUTION, Loosen the Lamp Unit Screw with - lamp with housing ty la1000

Get Panasonic PT-44LCX65 - 44inch Rear Projection TV PDF manuals and user guides
UPC - 037988975334
View all Panasonic PT-44LCX65 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

2 Grasp both sides of the Front Cover with your fingertips and pull it from the Projection Display to remove it. 5 (1) Insert the new Lamp Unit being careful of the insertion direction. • Press on the arrow mark to make sure insertion is done correctly. (2) Tighten the Lamp Unit Screw with a screwdriver. Front Cover (2) (1) Lamp unit screw Lamp unit 3 (1) Turn the Lock/Open Knob to the left. (2) Pull the Lamp Cover out and down to open it. (1) Lock/Open Knob (2) Lamp Cover Notes: • Properly dispose of old lamp. Please see page 66. • Attach the lamp unit and lamp unit housing door securely. If the lamp unit and lamp unit housing door are not attached securely, the protective circuit will be activated and the lamp will not turn on. 6 (1) Close the Lamp Cover. (2) Turn the Lock/Open Knob to the right. (2) Lock/Open Knob 4 (1) Loosen the Lamp Unit Screw with a screwdriver. (2) Grasp the Lamp Unit Handle as shown in the diagram, and slowly remove the Lamp Unit from the Projection Display. (1) Lamp Cover Lamp unit handle (1) 7 Replace the Front cover. (2) Lamp unit screw CAUTION • Because the lamp unit is hot immediately after its use, touching it may cause burns. • Please allow the lamp to cool before handling or replacing the lamp unit. Front Cover After lamp replacement, you must reset the lamp time. Refer to the instructions enclosed with the lamp unit (Part No.: TY-LA1000). Information 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
67
Information
Grasp both sides of the Front Cover with your
fingertips and pull it from the Projection Display
to remove it.
Front Cover
(1) Turn the Lock/Open Knob to the left.
(2)
Pull the Lamp Cover out and down to open
it.
Lock/Open Knob
Lamp Cover
(1) Loosen the Lamp Unit Screw with a
screwdriver.
(2)
Grasp the Lamp Unit Handle as shown in the
diagram, and slowly remove the Lamp Unit
from the Projection Display.
Lamp unit screw
Lamp unit handle
• Because the lamp unit is hot immediately after its
use, touching it may cause burns.
• Please allow the lamp to cool before handling or
replacing the lamp unit.
(1)
Insert the new Lamp Unit being careful of the
insertion direction.
• Press on the arrow mark to make sure
insertion is done correctly.
(2) Tighten the Lamp Unit Screw with a
screwdriver.
Notes:
• Properly dispose of old lamp. Please see page 66.
• Attach the lamp unit and lamp unit housing door securely.
If the lamp unit and lamp unit housing door are not
attached securely, the protective circuit will be activated
and the lamp will not turn on.
Replace the Front cover.
2
3
4
5
7
CAUTION
After lamp replacement, you must reset the lamp
time. Refer to the instructions enclosed with the
lamp unit (Part No.: TY-LA1000).
(1)
Front Cover
Lamp unit screw
Lamp unit
(2)
(1)
(2)
(1)
(2)
(1) Close the Lamp Cover.
(2) Turn the Lock/Open Knob to the right.
Lock/Open Knob
Lamp Cover
6
(2)
(1)