Panasonic RP-BTGS10-K RP-BTGS10-K Owner's Manual (English) - Page 13

Useful functions, Restoring to the factory settings

Get Panasonic RP-BTGS10-K PDF manuals and user guides View all Panasonic RP-BTGS10-K manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

ENGLISH ■ Note • There may be instances when hands free operation needs to be set on the Bluetooth® enabled phone. • Depending on the Bluetooth® enabled phone, you may hear incoming and outgoing call ringtones of the phone from the headset. • If you cannot check the outgoing call, press and hold the Call button on the headset for approximately 2 seconds and switch the device used for the call from the Bluetooth® enabled phone to the headset. (HFP only) Each time you perform the above operation when dialing or taking a call, the calling device will switch between the Bluetooth® enabled phone and the headset. Useful functions Selecting LED pattern After turning on the headset, you can switch the LED blinking pattern between the sports and normal modes. Press the LED pattern switch button. The normal mode is set as the factory default setting. The LED blinking pattern cannot be switched during Bluetooth® device pairing/connection operation. When the Bluetooth® connection is completed, the LED on the top will blink in blue. When the Bluetooth® connection is completed, the LED on the top will blink in blue and red. In addition, the LEDs near the right and left speakers will blink in blue when the LED on the top blinks in blue. Auto power off If the headset is silent for 5 minutes and operations for Bluetooth® devices are idle during that period, four-tone beep will sound and the power will be automatically turned off. Low battery notification When the battery level is low during use of the headset, the blue blinking LED on the top will change to red. Two beeps will sound once every minute. When the battery runs out, long beep will sound and then the power will be automatically turned off. Restoring to the factory settings When you want to delete all pairing device information, etc., you can restore the headset to the factory settings (original settings upon purchase). 1 Turn on the headset. • Check that the headset is not connected with other Bluetooth® devices. 2 Press and hold the LED pattern switch button and pairing button for 5 seconds or more simultaneously. • A two-tone beep followed by a four-tone beep will sound. The LEDs on the top and near the right and left speakers will blink in blue 3 times. The headset will restore to the factory settings. VQT5C48 13 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
VQT5C48
13
13
ENGLISH
Restoring to the factory settings
Useful functions
■
Note
• There may be instances when hands free operation needs to be set on the
Bluetooth
®
enabled phone.
• Depending on the Bluetooth
®
enabled phone, you may hear incoming and
outgoing call ringtones of the phone from the headset.
• If you cannot check the outgoing call, press and hold the Call button
on
the headset for approximately 2 seconds and switch the device used for
the call from the Bluetooth
®
enabled phone to the headset.
(
HFP
only) Each time you perform the above operation when dialing or
taking a call, the calling device will switch between the Bluetooth
®
enabled
phone and the headset.
Selecting LED pattern
After turning on the headset, you can switch the LED blinking pattern between
the sports and normal modes. Press the LED pattern switch button. The
normal mode is set as the factory default setting. The LED blinking pattern
cannot be switched during Bluetooth
®
device pairing/connection operation.
<Normal mode>
When the Bluetooth
®
connection is completed, the LED on the top will
blink in blue.
<Sports mode>
When the Bluetooth
®
connection is completed, the LED on the top
will blink in blue and red. In addition, the LEDs near the right and left
speakers will blink in blue when the LED on the top blinks in blue.
Auto power off
If the headset is silent for 5 minutes and operations for Bluetooth
®
devices
are idle during that period, four-tone beep will sound and the power will be
automatically turned off.
Low battery notification
When the battery level is low during use of the headset, the blue blinking
LED on the top will change to red. Two beeps will sound once every minute.
When the battery runs out, long beep will sound and then the power will be
automatically turned off.
When you want to delete all pairing device information, etc., you can restore
the headset to the factory settings (original settings upon purchase).
1
Turn on the headset.
•
Check that the headset is not connected with other Bluetooth
®
devices.
2
Press and hold the LED pattern switch button and pairing button
for 5 seconds or more simultaneously.
•
A two-tone beep followed by a four-tone beep will sound. The LEDs on
the top and near the right and left speakers will blink in blue 3 times.
The headset will restore to the factory settings.