Pfaff 63 Owner's Manual

Pfaff 63 Manual

Get Pfaff 63 PDF manuals and user guides View all Pfaff 63 manuals
Add to My Manuals
Save this manual to your list of manuals

Pfaff 63 manual content summary:

  • Pfaff 63 | Owner's Manual - Page 1
  • Pfaff 63 | Owner's Manual - Page 2
    4 PFAFF 63 Light-Weight Portable Electric Sewing Machine (Central Bobbin Machine) For Straight-Away Stitching INSTRUCTION BOOK •1
  • Pfaff 63 | Owner's Manual - Page 3
    the ewing quickly, is easy to operate, and requires little attention and service. lust follow these smple instructions and sewing will become a lasting pleasure. G.M.PFAFF AG 1. What Belongs to Your Machine? 1 package of assorted needles, System 705 R I tape measure 5 bobbins No. 2030 1 shuttle
  • Pfaff 63 | Owner's Manual - Page 4
    3. Upper thread guide 4. Collapsible spool pins 5. Winder spindle 6. Winder engaging lever 7, Balance wheel 8. Milled screw for engaging the sewing mechanism 9, Stitch length limiting lever 10. Stitch length lever 11. Motor support 12. Spool pins 13. Pin cushion 14. Sewing machine base 15. Accessory
  • Pfaff 63 | Owner's Manual - Page 5
    -length arm cover, removable 2. Thread take-up 3. Upper thread guide 4. Collapsible spool pins 5. Winder spindle 6. Winder engaging lever 7. Balance wheel 14. Sewing machine base 17. Feed lowering button 2L Needle plate 23. Fold-away support for bed plate extension 24. Bed plate extension 25. Bed
  • Pfaff 63 | Owner's Manual - Page 6
    starter under the table and plug the cable into the motor socket. Place the sewing machine case on table and unlock it. Pull the flap lighti Attention and the snap bow will release the cas Dont plug your machine into the line unless you have made sure that the line voltage top. corresponds
  • Pfaff 63 | Owner's Manual - Page 7
    I -D 0 0 C), C i5•- D . C • (0 -. CD :3-n 0(0 - a CD ',,
  • Pfaff 63 | Owner's Manual - Page 8
    that the flattened side of the shank faces to the right. Tighten needle clamp screw. 7. Winding the Bobbin Thread Photo 7 Photo 6 1. Disengage the sew ing mechanism. 2. Place cotton reel on the right reel pin. 3. 4. Pass the thread from cotton reel Thread end of thread inside-out 1, around
  • Pfaff 63 | Owner's Manual - Page 9
    N 8. Taking Out Bobbin Case Raise needle. Pull out bobbin case, holding it by the latch. While the latch remains open, the bobbin cannot fall out. 9. Inserting the Bobbin into the bobbin case. Hold bobbin as shown in the photo; the thread unwinding toward the operator. Photo 8 I 14 15 Photo 9
  • Pfaff 63 | Owner's Manual - Page 10
    Draw thread through slot, as illustrated. Hold bobbin in bobbin case and draw thread beneath the tension spring so that it comes out from underneath its end. Photo 10 16 17 Photo 11 I
  • Pfaff 63 | Owner's Manual - Page 11
    Hold bobbin case with thumb and midd le finger of your left hand. While the index finger holds the latch open, the bobbin cannot fall out. Place bobbin case on the center stud of the shuttle and release latch. Turn bobbin case with thumb and index finger so that bobbin case retainer H engages in
  • Pfaff 63 | Owner's Manual - Page 12
    V 0 0C- o 0 0 (9cQ C C - CD •-' CD ' - 0 CD 0 D- CD CD C ;c- CD 0 C CD < CD 0 - c- oL1 • CD Cl) CD -'CD Z (0 -+, -' 3 - - CC D CD D CD - - - CD - D0 0' 0D D c0 0 o S. C ;; C) CD ' ,$) .!' (D CD 0D -, (0 CD - c- - - D C CD z < CD c2_ CD 0 CD 2D CD -
  • Pfaff 63 | Owner's Manual - Page 13
    • . . holding it loosely over the protrud ing prong 3, making sure Ihatthread lies properly in the lop of the prong. 4. Release lever 1 The thread is pulled through the needle eye by the reversing prong 3. 4 Photo 16 Photo 17 I 22 23 Photo 18
  • Pfaff 63 | Owner's Manual - Page 14
    0 0 t- -0 CD < 0ö-CD o n -4 0C 0 -v 3C 0. '0 CD o - :r 0 - a< 3. C Cr1 = CD D 0 a CD 0C 0 ( CD C- CD (0 CD C C 0 CD 0 - CD-, C 0 D0 CD CD nD CD CD 0 -$, C- 0 CD 0 D_. 0 n CDCD CD C C C 0 U- C CD - CD ('-C C C 0 oC3 CD CD - CD C -I CD CD 0 CD
  • Pfaff 63 | Owner's Manual - Page 15
    14. Adjusting the Bobbin Thread Tension For Lighter tension, turn tension screw left -((, using the small screw driver. Turning the screw right will in crease the tension. 15. Correct Tension Regulation with perfect interlocking of upper and lower threads in the center of the ma terial results
  • Pfaff 63 | Owner's Manual - Page 16
    16. Setting the Stitch Length 1. Set stitch length limiting lever B at the desired stitch length indicated on the scale. 2. Push stitch length lever A to its right stop to obtain a forward stitch of the length of stitch set. 3. For reverse stitching, turn lever A to its left stop. 17. Removing the
  • Pfaff 63 | Owner's Manual - Page 17
    18. Correct Regulation of the Pressure on the Material assures uniformity of the stitch length and prevents injury of the material by the feed dog. Turning screw V left cE( will ease the pressure for thin and flimsy fabrics; turning it right will increase the pressure for heavy materials.
  • Pfaff 63 | Owner's Manual - Page 18
    Photo 29 - 20. For Taking off the Balance Wheel to remove odd thread between balance wheel and arm shaft bushing, 1. Loosen screw a. 2. Loosen milled screw b, turning it to the left. 3. Remove dog ring 1 (photo 30),take off balance wheel, and remove thread. When replacing the dog ring, make sure
  • Pfaff 63 | Owner's Manual - Page 19
    A Photo 31 Photo 32 21. Servicing and Maintenance. Regular and proper oiling serves to increase the life of your machine, Apply oil only at the points marked by arrows. Do not forget to oil the rear arm shaft bushing, half covered by the winder wheel
  • Pfaff 63 | Owner's Manual - Page 20
    Apply a drop of oil from time to time in the shuttle race. A dry race will wear off rapidly. 22. Removing the Shuttle becomes necessary when thread has entered into the race. 1. Loosen wing screw a and push gib b downwards. Photo 33 36 37 Photo 34
  • Pfaff 63 | Owner's Manual - Page 21
    3cL n - CD - 2. CD - -C :- - _.CD - _, C o D CD 00 0- -0 o 300 0 D - D C-D 00 zr 0 (7' - 0 CD CD 0 C- - C0 D D. Co (0 0 _c :y 0 CD D
  • Pfaff 63 | Owner's Manual - Page 22
    Insert a fresh bulb so that the guiding pins will slide into the slots of the socket. Push the bulb up in the socket, turn it ight and let it snap into position. The bulb is now firmly secured. Photo 37 24. How to Remedy Sewing Troubles Skipping of Stitches: Cause: Needle rrnlNolerly inserted.
  • Pfaff 63 | Owner's Manual - Page 23
    43 I Remedy: Shorten belt or insert a piece for length ening. Cut the belt straight. Clean and oil shuttle race. Use only PFAFF sewing machine oi never salad oil or glycerine. Unscrewbothfeeddogand needle plah and readjust properly. Disengage winder. Remove and unwind thread with the aic of a thin
  • Pfaff 63 | Owner's Manual - Page 24
    Needle Breakage Cause: Needle bent and struck by the point of the hook. Needle too thin or thread too thick. Upper thread tension too tight, thus bending needle. Needle bent and strikes needle plate due to the material being pulled or pushed. Bobbin case inserted improperly. Uneven Stitches Remedy
  • Pfaff 63 | Owner's Manual - Page 25
    off needle a graver. plate and remove lint Increase pressure (see section 1 8). by tigthening screw V Clean and oil machine as per instructions in sections 21 and 22. 46 Note: If machine does not feed at gaged or stitch length lever all, set check whether at zero. feed dog has not
  • Pfaff 63 | Owner's Manual - Page 26
    25. Edge stitching with several parallel seams is easily done with the edge guide No. 25820 in connection with the standard foot No. 43729. Use the edge stitcher No. 25553 fo stitching close to the edge. 48 49 Photo 38
  • Pfaff 63 | Owner's Manual - Page 27
    0 0 C) w0 ' (-7, S 0 0 t3 - -' Q C Cr2 CD 9% CD Ct, CD c2_ Ct, CD D - z, - - .0 n- = 0 C (0 CD CD -. C,C CC CD Q : C < C,, o CD - -, c Co t, CD D Co C C,, t'.) CD 0 Cj, 0 C C CD (C 0 0 D CD CC - Ct, CD - 0.. -o ,, C ;• D CD 1•t. r-.
  • Pfaff 63 | Owner's Manual - Page 28
    . can he produced with the hemmers Nos. 25576 and 25579. Feed material into the hemmer mouth sufficiently so that its folded edge strikes and is guided by the left edge of the hemmer. To facilitate insertion of the material in the hemmer, clip off the corner of the material. Photo 41
  • Pfaff 63 | Owner's Manual - Page 29
    . 4 E° CD D - :- CD 0 CD D0 3 0_ D CD 0 -., CD -< -. 0 -" (0 CD CD g 3 CD CD . - -3 o D - 5• - CD C - CD CD - D. CD CD ::5: -CD v, 0 CD 0 0.. 0 a. - _,, - 0 2. n CD CD a.. . 0 - - 0 ' .! CD D -'-' - (CD E - -• CD -. _,. -. - CD o' (C CD CD D 2. -< o
  • Pfaff 63 | Owner's Manual - Page 30
    RuffHng Foot No.25547 (at an extra charge) is used for 3 purposes: 1. For the ruffling of the lower ply whereby the unruffled upper ply is guided in the slot of the foot. Depending on the stitch length, the lower ply is more or less shoved to gether by the fend dog
  • Pfaff 63 | Owner's Manual - Page 31
    CM -_'w v - CM 3- - CD o C.D, D -., C.. CD 0 C V , CD 0 C C.. o CL (nC__ DC CD CD !!L .0 (DC ' • fl QD =D -C - o CC - ' :- -, C - • -. CT D oo= CD C • CL o. C -, D 0 CC C o -. - - CT 0 o- CD CD ..- > CD CT < 2 - CD -I-, _. 0 -s C cC 2. E CD - CT CD
  • Pfaff 63 | Owner's Manual - Page 32
    * ' : . 0 : 0' c 0' - ---------- S -- ---- . 0 C_fl C E D> D-f 9c •:- 90 m 0 QQ__ o Q_ cn CD - . Qoo __ o ."En ;• . - CD . - :: = 0 D - ,, D CD . c D ( 0 g0: - < CD . cD zE -'-z0 0-, '-' •' -i
  • Pfaff 63 | Owner's Manual - Page 33
    in position with the bed plate slide (see photo 53). 3. Screw on Darning Attachment No. 53003. 4. Suspend presser baron face plate with hook No. 46128. 63
  • Pfaff 63 | Owner's Manual - Page 34
    5. Lower presser bar lever. Photo 53 6. Insert and stretch defective material in hoop. The feed cover plate facilitates the guiding and increases the tension of the materiaL with the presser bar suspended frresser bar lever must point down Is as otherwise the upper thread DII
  • Pfaff 63 | Owner's Manual - Page 35
    -Q CD 0 o CD 3 2' - 0 a - CD CrC o CDD CD -' CD - r CD 60 CD CD c CD CD 0' 0' 1 0' CD 0 0 crC C' CD 0 _2_ t2. CD CD 0 CD CD C-D , aQ rC CD CD - CD D n •C E - 0 CD 0 - CD = CD ,, CD * 0 CD < E CD 0'- CD -• CD CD a 3 CD 0 2. 3co 0 2 CD 00 CD r, 0 -. - CD C
  • Pfaff 63 | Owner's Manual - Page 36
    holes, the are stitched as shown in photo 57. Photo 57 33. Embroidering embroidering, the machine is set up in the same manner as for mending. material is stretched in the hoop and then guided under the needle following o preliminary exercise, until the necessary practice has been acquired, it is
  • Pfaff 63 | Owner's Manual - Page 37
    Belongs to Your Machine? 3 2. Do You Know Your Machine? 4 3. Setting Up the Machine 8 4. Engaging the Sewing Mechanism 10 5. Relative Balance Whoel 32 21. Servicing and Maintenance 341 22. Removing the Shuttle 23. The Sew Light 391 24, How to Remedy Sewing Troubles 41 2 Fdq Stitching
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37