Pioneer DEH-P710BT Installation Manual - Page 2

Contents, Connecting the units - remote

Get Pioneer DEH-P710BT - Premier Radio / CD PDF manuals and user guides
UPC - 012562943534
View all Pioneer DEH-P710BT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

Contents Connecting the units 2 Connecting the power cord 4 When using a subwoofer without using the optional amplifier......... 6 When connecting to separately sold power amp 8 When connecting speakers without using the internal amplifier........ 10 Installation 12 DIN Front/Rear-mount 12 Removing or attaching the trim ring 12 DIN Front-mount 13 DIN Rear-mount 13 Fastening the front panel 14 Installing the microphone 14 When installing the microphone on the sun visor 14 When installing the microphone on the steering column 15 Adjusting the microphone angle 15 Installing the steering remote control.......... 15 Installing the unit on a left-hand drive car........... 16 Connecting the units Note • When this unit is installed in a vehicle without ACC (accessory) position on the ignition switch, red cable must be wired to the terminal that can detect the operation of the ignition key. Otherwise, battery drain may result. F ACC O F O OF OF N STAR N STAR T T ACC position No ACC position • Use this unit in other than the following conditions could result in fire or malfunction. - Vehicles with a 12-volt battery and negative grounding. - Speakers with 50 W (output value) and 4 ohm to 8 ohm (impedance value). • To prevent short-circuit, overheating or malfunction, be sure to follow the directions below. - Disconnect the negative terminal of the battery before installation. - Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts. - Place all cables away from moving parts, such as gear shift and seat rails. - Place all cables away from hot places, such as near the heater outlet. - Do not pass the yellow cable through a hole into the engine compartment to connect to a battery. - Cover any disconnected cable connectors with insulating tape. - Do not shorten any cables. - Never cut the insulation of the power cable of this unit in order to share the power to other equipment. Current capacity of the cable is limited. - Use a fuse of the rating prescribed. - Never wire the speaker negative cable directly to ground. - Never band together multiple speaker's negative cables. 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
±
Contents
Connecting the units
Connecting the units
............................
2
Connecting the power cord
...............................
4
When using a subwoofer
without using the optional amplifier
........
6
When connecting to
separately sold power amp
........................
8
When connecting speakers
without using the internal amplifier
.......
10
Installation
...........................................
12
DIN Front/Rear-mount
...................................
12
Removing or attaching the trim ring
....................
12
DIN Front-mount
....................................................
13
DIN Rear-mount
.....................................................
13
Fastening the front panel
..............................
14
Installing the microphone
.............................
14
When installing the microphone
on the sun visor
.................................................
14
When installing the microphone
on the steering column
.....................................
15
Adjusting the microphone angle
..........................
15
Installing the steering remote control
.........
15
Installing the unit on a left-hand drive car
...........
16
Note
• When this unit is installed in a vehicle without
ACC (accessory) position on the ignition switch,
red cable must be wired to the terminal that can
detect the operation of the ignition key. Otherwise,
battery drain may result.
A
C
C
O
N
S
T
A
R
T
O
F
F
O
N
S
T
A
R
T
O
F
F
ACC position
No ACC position
• Use this unit in other than the following
conditions could result in fire or malfunction.
— Vehicles with a 12-volt battery and negative
grounding.
— Speakers with 50 W (output value) and 4 ohm
to 8 ohm (impedance value).
• To prevent short-circuit, overheating or
malfunction, be sure to follow the directions
below.
— Disconnect the negative terminal of the
battery before installation.
— Secure the wiring with cable clamps or
adhesive tape. To protect the wiring, wrap
adhesive tape around them where they lie
against metal parts.
— Place all cables away from moving parts, such
as gear shift and seat rails.
— Place all cables away from hot places, such as
near the heater outlet.
— Do not pass the yellow cable through a hole
into the engine compartment to connect to a
battery.
— Cover any disconnected cable connectors with
insulating tape.
— Do not shorten any cables.
— Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly
to ground.
— Never band together multiple speaker’s
negative cables.