Polaroid DRM-2001G User Manual - Page 45

Troubleshooting Guide

Get Polaroid DRM-2001G - DVDr / HDDr PDF manuals and user guides View all Polaroid DRM-2001G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Troubleshooting Guide Before contacting service personnel, please check possible problems and solutions below: No power SYMPTOM No sound No picture No color Disc cannot be played Remote control malfunction Sudden malfunction Picture dividing External signals cannot be recorded POSSIBLE CAUSE 1. Power supply disconnected 2. Bad connection between power plug and receptacle 3. Power of receptacle switched off 1. Incorrect input connection 2. Disc is deformed or dirty 3. System is in mute status 1. Incorrect signal connection 2. Incorrect TV status 3. TV system out mode is Progressive, but your TV system is Interlace mode 1. Wrong TV system selection 2. Improper color adjustment 3. Incorrect video output 1. No disc in drive 2. Disc placed incorrectly 3. Moisture condensed in unit 4. Not in playing status 5. Wrong disc format 6. Disc dirty 1. Remote control not directed at sensor 2. Receiving distance is more than 8 meters 3. Low voltage in remote control batteries 4. Outside obstacle between unit and remote control 1. Bad disc quality 2. Button was pressed mistakenly 3. Outside static 1. Selected system is incompatible with disc 1. Incorrect system connection 2. No disc or re-recordable disc 3. Disc has been finished 4. No free disc space REMEDY 1. Connect to power supply 2. Plug again or replace receptacle with new one 3. Switch on receptacle 1. Connect inputs properly 2. Clean of fix disc 3. Press "MUTE" button 1. Connect the inputs correctly 2. Re-adjust TV/AV status 3. Press PS/IS to angle or mode 1. Set up system by pressing "SYSTEM" button on remote control 2. Readjust color 3. Check for correct video output settings 1. Insert disc 2. Put disc on disc tray properly with label side up 3. Leave unit on for about an hour (without disc) before using again 4. Press "PLAY" button to switch playing status 5. Please with supported disc format 6. Clean disc with soft cloth from center to edge 1. Direct remote control at sensor 2. Reduce receiving distance 3. Replace batteries 4. Remove obstacle 1. Wait 5-10 seconds, playback will be restored 2. Turn off and restart unit 3. Shut off for 1-2 minutes and restart unit 1. Set up correct system 1. Connect properly 2. Insert recordable disc 3. Change disc 4. Change disc No monitor signal Timer recording cannot be done Recording aborted halfway 1. Input source not prepared 2. Incorrect video output system 3. Actual input source not consistent with selected 1. Disc does not meet requirements 2. Wrong time setting 3. Input source does not work properly during recording time 4. System power failure 1. There is no free disc space 2. Bad disc quality 45 1. Prepare input source 2. Switch video output system 3. Select proper input source 1. Replace with new disc 2. Set up time again 3. Ensure input source works correctly during recording time 4. Set system to standby 1. Replace with blank disc 2. Replace with high quality disc

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Troubleshooting Guide
45
Before contacting service personnel, please check possible problems and solutions below:
S
YMPTOM
P
OSSIBLE
C
AUSE
R
EMEDY
No power
Power supply disconnected
Bad connection between power
plug and receptacle
Power of receptacle switched off
1.
2.
3.
Connect to power supply
Plug again or replace receptacle
with new one
Switch on receptacle
1.
2.
3.
No sound
Incorrect input connection
Disc is deformed or dirty
System is in mute status
1.
2.
3.
Connect inputs properly
Clean of fix disc
Press “MUTE” button
1.
2.
3.
No picture
Incorrect signal connection
Incorrect TV status
TV system out mode is
Progressive, but your TV system
is Interlace mode
1.
2.
3.
Connect the inputs correctly
Re-adjust TV/AV status
Press PS/IS to angle or mode
1.
2.
3.
No color
Wrong TV system selection
Improper color adjustment
Incorrect video output
1.
2.
3.
Set up system by pressing
“SYSTEM” button on remote
control
Readjust color
Check for correct video output
settings
1.
2.
3.
Disc cannot be played
No disc in drive
Disc placed incorrectly
Moisture condensed in unit
Not in playing status
Wrong disc format
Disc dirty
1.
2.
3.
4.
5.
6.
Insert disc
Put disc on disc tray properly with
label side up
Leave unit on for about an hour
(without disc) before using again
Press “PLAY” button to switch
playing status
Please with supported disc format
Clean disc with soft cloth from
center to edge
1.
2.
3.
4.
5.
6.
Remote control malfunction
Remote control not directed at
sensor
Receiving distance is more than
8 meters
Low voltage in remote control
batteries
Outside obstacle between unit
and remote control
1.
2.
3.
4.
Direct remote control at sensor
Reduce receiving distance
Replace batteries
Remove obstacle
1.
2.
3.
4.
Sudden malfunction
Bad disc quality
Button was pressed mistakenly
Outside static
1.
2.
3.
Wait 5-10 seconds, playback will
be restored
Turn off
and restart unit
Shut off
for 1-2 minutes and
restart unit
1.
2.
3.
Picture dividing
Selected system is incompatible
with disc
1.
Set up correct system
1.
External signals cannot be
recorded
Incorrect system connection
No disc or re-recordable disc
Disc has been finished
No free disc space
1.
2.
3.
4.
Connect properly
Insert recordable disc
Change disc
Change disc
1.
2.
3.
4.
No monitor signal
Input source not prepared
Incorrect video output system
Actual input source not
consistent with selected
1.
2.
3.
Prepare input source
Switch video output system
Select proper input source
1.
2.
3.
Timer recording cannot be done
Disc does not meet
requirements
Wrong time setting
Input source does not work
properly during recording time
System power failure
1.
2.
3.
4.
Replace with new disc
Set up time again
Ensure input source works
correctly during recording time
Set system to standby
1.
2.
3.
4.
Recording aborted halfway
There is no free disc space
Bad disc quality
1.
2.
Replace with blank disc
Replace with high quality disc
1.
2.