Polaroid TDA-03211C User Manual - Page 60

SET UP, Enter - troubleshooting

Get Polaroid TDA-03211C PDF manuals and user guides View all Polaroid TDA-03211C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Programming Your Remote Control Changing Volume Lock The remote comes preset to allow independent volume control of each selected device (Global Volume Unlock). However, you may change the Volume Lock setting to Global Volume Lock so that one device's volume will control volume in all other modes. After that, you can perform Individual Volume Unlock on a selected device to set its volume control for independent operation or Global Volume Unlock to remove all volume locking. Locking Volume Control to One Mode (Global Volume Lock) Press and hold SET UP until the red LED blinks twice; then release. Enter 9-9-3 and then press the mode key for the device you want to control volume (for example,TV). The LED blinks twice. Now when you press VOL+, VOL-, or Mute, the selected device (for example, TV) will control the volume regardless of the current mode. Unlocking All Volume Control (Restoring Global Unlock) Press and hold SET UP until the red LED blinks twice; then release. Enter 9-9-3 and then press VOL+. The LED blinks four times. Volume is now independently controlled for all programmed devices. Unlocking a Single Device's Volume Control Press a device key (TV, VCR/DVD, CBL/ SAT, or AUX). Press and hold SET UP until the red LED blinks twice; then release. Enter 9-9-3 and then press VOL-. The LED blinks four times. Volume is now independently controlled for the selected devices. Troubleshooting PROBLEM SOLUTION LED does not blink when you press a key. Replace battery with new AAA size battery. LED blinks when you press a key, but device does not respond. Make sure the remote is aimed at your device and is not more than 15 feet away LED blinks one long blink. An entry error has occurred (for example, wrong key). Try entry sequence again. Remote does not control devices or commands are not working properly. Try all listed codes for the device. Make sure the device operates with an infrared remote control. CH▲, CH▼, and LAST do not work for your RCA TV. Due to RCA design from 1983 to 1987, only the original remote control will operate these functions. No volume on a device. See "Changing Volume Lock". Channels do not change properly. If the original remote control required you to press Enter to change channels, press Enter on this remote after entering the channel number. 58

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
58
Programming Your
Remote Control
n
Press and hold
SET UP
until the red LED blinks twice; then release.
o
Enter
9-9-3
and then press the mode key for the device you want to control volume (for
example,TV). The LED blinks twice. Now when you press VOL+, VOL-, or Mute, the selected
device (for example, TV) will control the volume regardless of the current mode.
Changing Volume Lock
The remote comes preset to allow independent volume control of each selected device (Global
Volume Unlock). However, you may change the Volume Lock setting to Global Volume Lock so that
one device’s volume will control volume in all other modes. After that, you can perform Individual
Volume Unlock on a selected device to set its volume control for independent operation or Global
Volume Unlock to remove all volume locking.
Unlocking All Volume Control (Restoring Global Unlock)
n
Press and hold
SET UP
until the red LED blinks twice; then release.
o
Enter
9-9-3
and then press VOL+. The LED blinks four times.
Volume is now independently controlled for all programmed devices.
Unlocking a Single Device’s Volume Control
n
Press a device key (TV, VCR/DVD, CBL/ SAT, or AUX).
o
Press and hold
SET UP
until the red LED blinks twice; then release.
p
Enter 9-9-3 and then press VOL-. The LED blinks four times. Volume is now
independently controlled for the selected devices.
Locking Volume Control to One Mode (Global Volume Lock)
Troubleshooting
PROBLEM
LED does not blink when you press a key.
LED blinks when you press a key, but
device does not respond.
LED blinks one long blink.
Remote does not control devices or
commands are not working properly.
CH
▲
, CH
▼
, and LAST do not work for your
RCA TV.
No volume on a device.
Channels do not change properly.
SOLUTION
±
Replace battery with new AAA size battery.
±
Make sure the remote is aimed at your device and is not more
than 15 feet away
±
An entry error has occurred (for example, wrong key). Try entry
sequence again.
±
Try all listed codes for the device. Make sure the device operates with
an infrared remote control.
±
Due to RCA design from 1983 to 1987, only the original remote
control will operate these functions.
±
See “
Changing Volume Lock
”.
±
If the original remote control required you to press
Enter
to
change channels, press
Enter
on this remote after entering the
channel number.