Poulan 1980-02 User Manual
Poulan 1980-02 Manual
 |
View all Poulan 1980-02 manuals
Add to My Manuals
Save this manual to your list of manuals |
Poulan 1980-02 manual content summary:
- Poulan 1980-02 | User Manual - Page 1
Chain Saw OWNER'S MANUAL CAUTION: Read Rules for Safe Operation Carefully. Beaird-Poulan Division Emerson Electric Co. Shreveport, Louisiana Record in the space provided below the model number and serial number of your saw. Model No. Serial No - Poulan 1980-02 | User Manual - Page 2
Get it Sharpened! 0 Don't Press Hard - Light pressure is enough. Heavy pressure can cause unsafe conditions. Check for a dull chain or worn bar. (See Guide Bar Maintenance and Chain Sharpening). 0 Cut Only At High Speeds - Keep the throttle wide open when cutting. Don't run the engine at high speed - Poulan 1980-02 | User Manual - Page 3
Chain Installation 4 Chain Adjustment 4 Bow Installation 4 Operating Instructions 5 Cutting Tips 5 Bow Cutting Tips 5 Felling 6 16:1) '/2 pint oil to 1 Gal. Reg. Gasoline Automatic/Manual Starter Handle-pull to operate Sprocket Nose Guide Bar Filler Cap-Fuel (gas-oil mix) Chain O • - Poulan 1980-02 | User Manual - Page 4
) Bumper - (right) Screw - Bumper Mounting (1/4-20 x I% hex head) 4 4.® BOW ASSEMBLY INSTRUCT: 1. Install two 23447 spacers o• slot on top and to the right. 2. Attach 1207 and 1208 bumpers 625567 screws and two 1615 locknuts. 3. Mount bow guide, chain and 11176 cover on saw while making sure that - Poulan 1980-02 | User Manual - Page 5
available from your authorized service dealer. OPERATING INSTRUCTIONS Before Starting gine flood, repeat starting instructions with Choke Knob CUTTING TIPS WARNING! Kickback may cause serious injury. Read all instructions carefully before using the bow guide. A BOW IS NOT 1. It is not for use by - Poulan 1980-02 | User Manual - Page 6
y GEN 4 ,94.„.7 5. Keep the chain tight and sharp. ----""// o o Correct Entry Area 0 Always begin cutting in the correct entry area of the bow. 2. Be sure the spur is in place against the log before beginning the cut. 3. Do not cut small limbs or brush with a bow. LOOK OUT FOR KICKBACK 1. - Poulan 1980-02 | User Manual - Page 7
Keep Both Hands On The Saw - keep a firm grip. 0 Be Sure Of Your Support - don't cut off balance. 0 Cut Up From The Bottom, Finish Down From trouble that you are not prepared to handle, take it to an authorized Service Dealer for service. He has been trained and is equipped to provide expert service - Poulan 1980-02 | User Manual - Page 8
trouble free cutting. Your authorized dealer or authorized master service center , the correct size file and jointer. Follow these instructions: 1. If possible, remove the chain from the a filing vise, tension the chain up snugly on the guide bar. 0 Filing 2. There are three angles that must - Poulan 1980-02 | User Manual - Page 9
Power Sharp Chain you will need a fileholder and the correct size file. Follow these instructions: 1. If possible, remove the chain from the saw and put it in a If you do not have a filing vise, tension the chain up snugly on the guide bar. Use a No. 5595 Fileholder and hold it level at a 24° angle
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
 |
 |
Poulan
Chain
Saw
OWNER'S
MANUAL
...
..
..
..
.
.
....
.
.
....
.
..
CAUTION:
Read
Rules
for
Safe
Operation
Carefully.
Beaird-Poulan
Division
Emerson
Electric
Co.
Shreveport,
Louisiana
Record
in
the
space
provided
below
the
model
num-
ber
and
serial
number
of
your
saw.
Model
No.
Serial
No
Retain
these
numbers
for
future
reference.