Poulan 1995-03 User Manual

Poulan 1995-03 Manual

Get Poulan 1995-03 PDF manuals and user guides View all Poulan 1995-03 manuals
Add to My Manuals
Save this manual to your list of manuals

Poulan 1995-03 manual content summary:

  • Poulan 1995-03 | User Manual - Page 1
    Poulan PRO® =7' 210 OPERATOR'S MANUAL A WARNING: Carefully read the Operator's Manual and follow all Warnings and Safety Instructions. Failure to do so can result in serious injury. MANUAL DEL OPERADOR A ADVERTENCIA: Lea el manual del operador y respete las advertencias e instrucciones de
  • Poulan 1995-03 | User Manual - Page 2
    INSTRUCTIONS.. .3 KNOW YOUR UNIT.. .6 ASSEMBLY . .7 FUELING YOUR ENGINE USING YOUR SAW ... TYPES OF CUTTING GENERAL MAINTENANCE PARTS & SERVICE GAP: OILER: FUEL MIX: MUFFLER: SPECIFICATION CHART 210 36ec 2.2 CID 14" Guide Bar Low Profile 3/8" Pitch Chrome Cutters 91 VG-52 Champion (CJ-7Y) .
  • Poulan 1995-03 | User Manual - Page 3
    safety rules. precautions, and operating instructions found in this manual. THIS SAW IS FOR OCCASIONAL engine stopped, muffler away from your body, and the guide bar and chain to the rear and covered preferably with does not guarantee the avoidance of these problems. Users who operate power toasts on
  • Poulan 1995-03 | User Manual - Page 4
    INSTRUCTIONS (See Additional Safety Instructions throughout this Manual WARNING Contact at the upper portion of the tip of the guide bar can cause the chain to dig into the object, not appear to stop instantly, contact your Authorized Service Dealer. Figure 2 Avoid Obstructions Hand Guard CHAIN
  • Poulan 1995-03 | User Manual - Page 5
    AND SAFETY INSTRUCTIONS (continued) section of this manual. For example. if improper tools are used to remove or hold the flywheel when servicing the clutch, structural while starling the engine. Never try to start the saw when the guide bar is in a cut or kerb 7. Use extreme caution when
  • Poulan 1995-03 | User Manual - Page 6
    Spark Arrestor Temperature Limiting Muffler R. CARTON CONTENTS KEY NQ I. Engine 2 Guide Bar - Operator's Manual (not shown) - Loose Parts Bag (nth shown) LOOSE PARTS BAG CONTENTS Chain Sere orh OTY. C. UNPACKING INSTRUCTIONS I . After removing the contents from the carton, check parts against
  • Poulan 1995-03 | User Manual - Page 7
    to understand its safe operation. It is important that you read your manual completely to become familiar with the unit before you begin assembly or (Figure 10) almost as far as it will go to the rear. 3. Mount the guide bar with the slotted end over the bar studs. Figure II. 4. Hold the chain with
  • Poulan 1995-03 | User Manual - Page 8
    up to normal operating temperature. • Chain tension is correct when the chain will move freely around the bar and chain does not sag beneath the guide bar. • Chain tensioning procedure. I CAUTION: Always wear gloves when handling the chain. The chain is sharp and can cut you even when it is not
  • Poulan 1995-03 | User Manual - Page 9
    check for a plugged oil hole in the guide bar. c. Keep sawdust and debris cleaned from the oil holes in the guide bar to allow an adequate oil flow to SURE TO READ THE FUEL FIVNI• OLING INFORMATION IN THE WARNINGS AND SAFETY INSTRUCTIONS BEFORE YOU BEGIN. IF YOU DO NOT UNDERSTAND THE SAFETY RULES, DO
  • Poulan 1995-03 | User Manual - Page 10
    animals a safe distance away from the work area when stalling or operating the saw -- a minimum of 10 meters (30 feet/ B. STARTING INSTRUCTIONS (Refer to the "Specifications" section for location of controls.) A WARNING Always wear gloves; safely footwear; snug fitting clothing; and eye, hearing
  • Poulan 1995-03 | User Manual - Page 11
    of dirt will quickly dull a chain and thus increase the possibility of kickback. A KICKBACK WARNING Contact at the upper portion of the tip of the guide bar can cause the chain to dig into the object, which stops the chain for an instant. The result is a lightning fast, reverse reaction which
  • Poulan 1995-03 | User Manual - Page 12
    tree starts to fall, stop say, dlldgetaway quiekiy an your planned retreat path. f. Be extremely cautious with partially fallen trees that may be poorly supported. When a tree doesn't fall completely, set the saw aside and pull down the tree with a cable winch, block and tackle, or tractor. To avoid
  • Poulan 1995-03 | User Manual - Page 13
    and chain damage, do not use a metal wedge. Do not attempt to restart your saw when it is pinched or hung in a log. 3. BUCKING WITHOUT A SUPPORT . Overcut with a 1/3 diameter cut. b. Roll log over and finish with an overcut. t Cut Pressure Side 21.:171 2nd Cut 2nd Cut c 1st Cut Pressure Side
  • Poulan 1995-03 | User Manual - Page 14
    safely and properly. b. Leave the larger limbs underneath the felled tree to support the tree as you work. c. Start at the base of the felled moving chain to contact any other branches or objects at the nose of the guide bar when limbing or pruning. Allowing such contact can result in serious injury
  • Poulan 1995-03 | User Manual - Page 15
    to your saw. A WARNING Have all chain saw service performed by a qualified service dealer other than the items listed in the maintenance section of this manual. • Check the condition of the guide bar each time the chain is sharpened. A worn guide bar will damage the chain and make cutting more
  • Poulan 1995-03 | User Manual - Page 16
    will protect you in the event of kickback. Instead, use the saw properly and carefully to avoid kickback. Proper operation is outlined in the Operator's Manual. Repairs on the chain brake must be made by qualified service personnel. Take you saw/chain to the place of purchase if purchased from
  • Poulan 1995-03 | User Manual - Page 17
    and consult the Troubleshooting section of this manual before beginning If the engine does not operate according to these instructions after repeating the adjusting steps, do not the carburethis process. use the unit For further assistance, contact your Authorized Service Dealer. The carburetor
  • Poulan 1995-03 | User Manual - Page 18
    of the reach of children. GAS CHAIN SAW STORAGE INSTRUCTIONS If your chain saw is to he stored for a a coating of oil to the entire surface of the guide bar and chain: wrap it in heavy paper or Rust and/or din in your fuel system will cause problems. • Store your unit in a well ventilated area and
  • Poulan 1995-03 | User Manual - Page 19
    H. TROUBLE SHOOTING dull on one side. 3. Guide bar bent or worn. I. Fill tank with correct fuel mixture. 2. See "Starting Instructions." 3. Install new plug/ 4. Contact your Authorized Service Dealer. 5. Contact your Authorized Service Dealer. 6. Contact your Authorized Service Dealer. 1. Clean or
  • Poulan 1995-03 | User Manual - Page 20
    Chain oil tank. Clean . Chain lubrication. Fill Saw chain. Inspect (sharpness, wear, damage) Check chain tension. Have sharpened - when dull. Guide has Inspect (wear, damage) Clean. Deburr Replace - when worn or damaged. Chain sprocket. Check - when replacing chain. Air filler Clean
  • Poulan 1995-03 | User Manual - Page 21
    your dealer/place of purchase. 2 Consult the yellow pages of your phone directory for the name of the nearest POULAN/WEED EATER Master Service Dealer (under - saws" for Chain Saws or under lawnmowers" for Trimmers. Bradautters. and Blowers). 3 For replacement pans. have available the following
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
Poulan
PRO®
=7'
210
OPERATOR'S
MANUAL
MANUAL
DEL
OPERADOR
MANUEL
DE
L'OPERATEUR
A
WARNING:
Carefully
read
the
Operator's
Manual
and
follow
all
Warnings
and
Safety
Instructions.
Failure
to
do
so
can
result
in
serious
injury.
A
ADVERTENCIA:
Lea
el
manual
del
operador
y
respete
las
advertencias
e
instrucciones
de
seguridad.
Al
no
hacerlo
cone
el
riesgo
de
sufrir
lesiones
graves.
A
AVERTISSEMENT
:
Lisez
attentivement
le
Manuel
de
l'operateur
et
suivez
les
instructions
de
s€curitd.
Dans
le
cas
contraire.
vous
risquez
des
blessures
graves.
MITNIWITIO