Poulan 271470 User Manual - Page 14
To Start Engine, Before Starting The Enigne, Tractor -- Model Number 271470 - carburetor
View all Poulan 271470 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 14 highlights
BEFORE STARTING THE ENIGNE CHECK ENGINE OIL LEVEL • The engine in your tractor has been shipped, from the factory, already filled with summer weight oil. • Check engine oil with tractor on level ground. • Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until "FULL" mark on dipstick is reached. Do not overfill. • For cold weather operation you should change oil for easier starting (See "OIL VISCOSITY CHART" in the Maintenance section of this manual). • To change engine oil, see the Maintenance section in this manual. ADD GASOLINE • Fill fuel tank. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness. IMPORTANT: When operating in temperatures below 32°F(0°C), use fresh, clean winter grade gasoline to help insure good cold weather starting. WARNING: Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. CAUTION: Fill to bottom of gas tank filler neck. Do not overfill. Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame. TO START ENGINE When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine. • Sit on seat in operating position, depress clutch/brake pedal and set parking brake. • Place gear shift lever in neutral (N) position. • Move attachment clutch to "DISENGAGED" position. • Move throttle control to choke position. NOTE: Before starting, read the warm and cold starting procedures below. • Insert key into ignition and turn key clockwise to "START" position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke position and retry. WARM WEATHER STARTING (50° F and above) • When engine starts, move the throttle control to the fast position. • The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above. COLD WEATHER STARTING ( 50° F and below) • When engine starts, allow engine to run with the throttle control in the choke position until the engine runs roughly, then move throttle control to fast position. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature. • The attachments can also be used during the engine warm-up period. NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See "TO ADJUST CARBURETOR" in the Service and Adjustments section of this manual. 14 GROUND DRIVE TRACTOR -- MODEL NUMBER 271470 KEY PART NO. NO. 1 ------ 2 146682 3 123666X 4 12000028 5 121520X 6 17060512 7 162240 8 131679 10 76020416 11 105701X 12 19151216 13 74550412 14 10040400 15 74490544 18 74780616 19 73800600 21 106933X 22 130804 24 73350600 25 106888X 26 19131016 27 76020412 28 145204 29 71673 30 174973 32 74760512 34 155071 35 120183X 36 19211616 37 1572H 38 131494 39 74760644 40 4470J DESCRIPTION Transaxle Dana D4360-139 (Order parts from transaxle Manufacturer) Spring Return Brake T/a Zinc Pulley Transaxle 18/20" tires Ring Retainer # 5100-62 Strap Torque 30 Degrees Screw 5/16-18 x 3/4 Bracket Saddle Shift T/a Rod Shf Sdl LY/YT Str Blk Pin Cotter 1/8 x 1 Cad Washer Plate 388 Sq Hole Washer 15/32 x 3/4 x 16ga Bolt 1/4-28unf Gr8 W/Patch Washer Lock Hvy Helical 1/4 Bolt Hex Flghd 5/16-18 x Gr. 5 Bolt Fin Hex 3/8-16 UNC x 1 Gr. 5 Nut Lock Hex W/Ins. 3/8-16 Unc Knob Rd 1/2-13 Plstc Thds Rod Brake Blk Zinc 26 840 Nut Hex Jam 3/8-16 Unc Spring Rod Brake 2 00 Zinc Washer 13/32 x 5/8 x 16 Ga Pin Cotter 1/8 x 3/4 Cad Rod Brake Parking Lt/Yt Cap Brake Parking Bracket Mtg Transaxle Bolt Hex Hd 5/16-18unc x 3/4 Shaft Asm Pedal Foot Bearing Nylon Blk 629 Id Washer 21/32 x 1 x 16 Ga Pin Roll 3/16 x 1" Pulley Idler Flat Bolt Fin Hex 3/8-16 UNC x 2-3/4 Gr. 5 Spacer Split 395 x 59 Bzp KEY PART NO. NO. 41 165838 42 19131312 47 127783 48 154407 49 123205X 50 74760624 51 73680600 52 73680500 53 105710X 55 105709X 56 74760620 57 160855 59 169691 61 17060612 62 8883R 63 140186 64 71170764 65 10040700 66 154778 70 134683 72 19132012 74 109502X 75 121749X 76 12000001 77 123583X 78 121748X 112 19091210 113 127285X 116 72110610 150 165850 151 19133210 170 173898 202 72110612 DESCRIPTION Keeper Belt Idler Washer 13/32 x 13/16 x 12 Ga Pulley Idler V Groove Plastic Bellcrank Asm. Clutch Retainer Belt Style Spring Bolt Hex Hd 3/8-16unc x1-1/2 Nut Crownlock 3/8-16 UNC Nut Crown Lock 5/16-18 Link Clutch 7 66 Spring Return Clutch 6 75 Bolt Fin Hex 3/8-16 unc x 1-1/4 V-Belt Gd Drive 9530 Keeper Belt Centerspan Screw 3/8-16 x 3/4 Cover Pedal Blk Round Pulley Eng Cl Mech 38deg Bolt Hex 7/16-20 x 4 Gr 5 Washer Lock Hlcl Spr 7/16 Keeper Belt Engine FP Guide Belt Mower Drive RH Washer 13/32 x 1-1/4 x12 Ga Spacer Axle Washer 25/32 x 1-1/4 x16 Ga E-ring #5133-75 Key Square 2 0 x 1845/ 1865 Washer 25/32 x1-5/8 x 16 Ga Washer 9/32 x 3/4 x 10 Ga Strap Torque LH LT Bolt Rdhd Sq Neck 3/8-16 x 1.25 Bushing Bellcrank GRD Drive Washer 13/32 x 2 x 10 Ga. Keeper Belt Transaxle Gear Bolt Carr. Sh 3/8-16 x 1-1/2 Gr. 5 NOTE: All component dimensions given in U. S. inches 1 inch = 25.4 mm 35