Poulan 460ZX User Manual - Page 36

Battery, Always use two wrenches for the terminal

Get Poulan 460ZX PDF manuals and user guides View all Poulan 460ZX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

MAINTENANCE Battery Your mower is equipped with a maintenance free battery and does not need servicing. However, periodic charging of the battery with an automotive type battery charger will extend its life. • Keep battery and terminals clean. • Keep battery bolts tight. • See chart for charging times. Always use protective glasses when handling the battery. STANDARD BATTERY 12.6V 12.4V 12.2V 12.0V 11.8V STATE APPROXIMATE BATTERY CHARGING TIME* TO FULL CHARGE AT 80OF / 27OC OF Maximum Rate at: 50 Amps 30 Amps 20 Amps 10 Amps CHARGE 100% - FULL CHARGE - 75% 20 min. 35 min. 48 min. 90 min. 50% 45 min. 75 min. 95 min. 180 min. 25% 65 min. 115 min. 145 min. 280 min. 0% 85 min. 150 min. 195 min. *Charging time depends on battery capacity, condition, age, temperature and efficiency of charger 370 min. Cleaning battery and terminals Corrosion and dirt on the battery and terminals can cause the battery to "leak" power. 1. Lift seat and rotate forward. 2. Disconnect BLACK battery cable first, then the RED battery cable and remove the battery from the machine. 3. Rinse the battery with plain water and dry. 4. Clean terminals and battery cable ends with wire brush until shiny. 5. Coat terminals with grease or petroleum jelly 6. Reinstall battery. Replacing battery 1. Lift seat and rotate forward. 2. Using two ½" wrenches disconnect BLACK battery cable then RED battery cable. 3. Position deck to lowest setting. 4. From underside of frame, remove the nuts that secure the battery hold-down. 5. Carefully remove the battery from the mower. 6. Install new battery with terminals in the same position as the old battery. 7. Reinstall battery hold-down and secure with nuts removed in Step 5. 8. First connect RED battery cable to positive (+) battery terminal with hex bolt and hex nut. 9. Connect BLACK grounding cable to negative (-) battery terminal with remaining bolt and nut 10. Tighten securely. 11. Lower seat IMPORTANT INFORMATION Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary. Always use two wrenches for the terminal screws. WARNING! Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc. Positive terminal must be connected first to prevent sparks from accidental grounding. Remove battery hold-down to replace battery 8050-109 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
mAINTENANCE
36
Battery
Your mower is equipped with a maintenance free
battery and does not need servicing. However,
periodic charging of the battery with an automotive
type battery charger will extend its life.
Keep battery and terminals clean.
•
Keep battery bolts tight.
•
See chart for charging times.
•
IMPORTANT INFORMATION
Do not attempt to open or remove caps or
covers. Adding or checking level of electrolyte
is not necessary.
Always use two wrenches for the terminal
screws.
WARNING!
Do not short battery terminals by
allowing a wrench or any other object
to contact both terminals at the same
time. Before connecting battery,
remove metal bracelets, wristwatch
bands, rings, etc.
Positive terminal must be connected
first to prevent sparks from accidental
grounding.
8050-109
Remove battery hold-down to replace battery
Cleaning battery and terminals
Corrosion and dirt on the battery and terminals can
cause the battery to “leak” power.
Lift seat and rotate forward.
1.
Disconnect BLACK battery cable first, then
2.
the RED battery cable and remove the battery
from the machine.
Rinse the battery with plain water and dry.
3.
Clean terminals and battery cable ends with
4.
wire brush until shiny.
Coat terminals with grease or petroleum jelly
5.
Reinstall battery.
6.
Replacing battery
Lift seat and rotate forward.
1.
Using two ½" wrenches disconnect BLACK
2.
battery cable then RED battery cable.
Position deck to lowest setting.
3.
From underside of frame, remove the nuts that
4.
secure the battery hold-down.
Carefully remove the battery from the mower.
5.
Install new battery with terminals in the
same
6.
position as the old battery.
Reinstall battery hold-down and secure with
7.
nuts removed in Step 5.
First connect RED battery cable to positive (+)
8.
battery terminal with hex bolt and hex nut.
Connect BLACK grounding cable to negative
9.
(-) battery terminal with remaining bolt and nut
Tighten securely.
10.
Lower seat
11.
Always use protective glasses when
handling the battery.
STANDARD
BATTERY
STATE
OF
CHARGE
APPROXIMATE BATTERY CHARGING TIME*
TO FULL CHARGE AT 80
O
F / 27
O
C
Maximum Rate at:
50 Amps
30 Amps
20 Amps
10 Amps
12.6V
100%
- FULL CHARGE -
12.4V
75%
20 min.
35 min.
48 min.
90 min.
12.2V
50%
45 min.
75 min.
95 min.
180 min.
12.0V
25%
65 min.
115 min.
145 min.
280 min.
11.8V
0%
85 min.
150 min.
195 min.
370 min.
*Charging time depends on battery capacity,
condition, age, temperature and efficiency of charger