ProForm 500 Cx Treadmill Uk Manual - Page 8

Fold And Move The Treadmill

Get ProForm 500 Cx Treadmill PDF manuals and user guides View all ProForm 500 Cx Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

5. Place the treadmill in the storage position (see HOW TO FOLD AND MOVE THE TREADMILL on page 24). Set the cylinder end of the Gas Spring (92) near the bracket on the base of the Uprights (84). See the two small inset drawings. Using your fingernail or the end of a screwdriver, press on the end of the Spring Pin (25), pivot it, and pull it out of the Gas Spring (92). Be careful to avoid losing the Spring Pin. Note: Extra Spring Pins are included. See drawing 5a. Press the cylinder end of the Gas Spring (92) onto the ball on the bracket. Next, insert the end of the Spring Pin (25) into two of the small holes in the end of the Gas Spring. Then, pivot the Spring Pin until it clips onto the Gas Spring. 5 25 84 25 92 Bracket 25 Cylinder 5a 25 92 Bracket 6. Raise the free end of the Gas Spring (92) to a vertical 6 position. Remove the Spring Pin (25) from the free end of the Gas Spring as described in step 5. If necessary, ro- tate the Gas Spring to align the end of the Gas Spring with the ball on the bracket on the Frame (58). Plug in the power cord as described on page 10. Turn on the power as described on page 12. Next, press the Incline increase and decrease buttons until the ball on the bracket is aligned with end of the Gas Spring (92). Then, press the end of the Gas Spring onto the ball. Note: It may be necessary to press the end of the Gas 6a Spring onto the ball while the Frame (58) is moving. See drawing 6a. Insert the Spring Pin (25) into the two indicated small holes in the end of the Gas Spring (92). Then, pivot the Spring Pin until it clips onto the Gas Spring. Press the Incline decrease button until the treadmill is at the lowest incline level. Then, unplug the power cord. 58 Bracket 25 92 Holes 92 25 7. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill. Note: Extra hardware may be included. Keep the included hex key in a secure place; the hex key is used to adjust the walking belt (see page 27). 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
8
7.
Make sure that all parts are properly tightened before you use the treadmill.
If there are sheets of clear
plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the tread-
mill. Note: Extra hardware may be included. Keep the included hex key in a secure place; the hex key is used
to adjust the walking belt (see page 27).
5.
Place the treadmill in the storage position (see HOW TO
FOLD AND MOVE THE TREADMILL on page 24).
Set the cylinder end of the Gas Spring (92) near the
bracket on the base of the Uprights (84).
See the two small inset drawings. Using your fingernail
or the end of a screwdriver, press on the end of the
Spring Pin (25), pivot it, and pull it out of the Gas Spring
(92).
Be careful to avoid losing the Spring Pin.
Note:
Extra Spring Pins are included.
See drawing 5a. Press the cylinder end of the Gas
Spring (92) onto the ball on the bracket. Next, insert the
end of the Spring Pin (25) into two of the small holes in
the end of the Gas Spring. Then, pivot the Spring Pin
until it clips onto the Gas Spring.
92
25
92
25
5
5a
84
Bracket
Cylinder
Bracket
6.
Raise the free end of the Gas Spring (92) to a vertical
position. Remove the Spring Pin (25) from the free end of
the Gas Spring as described in step 5. If necessary, ro-
tate the Gas Spring to align the end of the Gas Spring
with the ball on the bracket on the Frame (58).
Plug in the power cord as described on page 10. Turn on
the power as described on page 12. Next, press the
Incline increase and decrease buttons until the ball on
the bracket is aligned with end of the Gas Spring (92).
Then, press the end of the Gas Spring onto the ball.
Note: It may be necessary to press the end of the Gas
Spring onto the ball while the Frame (58) is moving.
See drawing 6a. Insert the Spring Pin (25) into the two
indicated small holes in the end of the Gas Spring (92).
Then, pivot the Spring Pin until it clips onto the Gas
Spring.
Press the Incline decrease button until the treadmill is at
the lowest incline level. Then, unplug the power cord.
25
92
Holes
25
92
6
6a
58
Bracket
25
25