ProForm 700 Gx Treadmill English Manual - Page 23

How To Fold And Move The Treadmill

Get ProForm 700 Gx Treadmill PDF manuals and user guides View all ProForm 700 Gx Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

If you purchase the optional chest pulse sensor, follow the steps below to install the receiver included with the chest pulse sensor. 1. Make sure that the power cord is unplugged. Remove the 3/4" Screw (33) and the Access Door 104 (105) from the Console Back (104). 2. Connect the wire on the receiver (A) to the indicated wire extending from the Console Back (104). Remove the paper from the adhesive pad on the back of the receiver. Hold the receiver so the small cylinder is near the lower edge of the receiver and is facing the Console Back as shown. Firmly press the receiver onto the indicated corner of the Access Door (105). Note: If there are two screws included with the chest pulse sensor and two plastic posts on the inside of the Access Door, attach the receiver to the plastic posts on the Access Door with the two screws. Wire A Cylinder 105 33 3. Make sure that no wires are pinched. Reattach the Access Door (105) with the 3/4" Screw (33). The other wires included with the receiver may be discarded. HOW TO FOLD AND MOVE THE TREADMILL HOW TO FOLD THE TREADMILL FOR STORAGE Before folding the treadmill, adjust the incline to the lowest position. If this is not done, the treadmill may become permanently damaged. Next, unplug the power cord. CAUTION: You must be able to safely lift 45 pounds (20 kg) to raise, lower, or move the treadmill. 1. Hold the treadmill in the locations shown by the arrow at the right. To decrease the possibility of injury, bend your legs and keep your back straight. As you raise the frame, make sure to lift with your legs rather than your back. Raise the frame about halfway to the vertical position. 2. Move your right hand to the position shown and hold the treadmill firmly. Using your left hand, pull the latch knob to the left and hold it. Raise the frame until the catch is past the latch pin. Slowly release the latch knob. Make sure that the catch is securely held by the latch pin. To protect the floor or carpet from damage, place a mat under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in temperatures above 85° Fahrenheit. 23 Latch Knob Pin Catch Closed

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be-
come permanently damaged. Next, unplug the power
cord. CAUTION: You must be able to safely lift 45
pounds (20 kg) to raise, lower, or move the treadmill.
1. Hold the treadmill in the locations shown by the arrow at
the right.
To decrease the possibility of injury, bend
your legs and keep your back straight. As you raise
the frame, make sure to lift with your legs rather than
your back.
Raise the frame about halfway to the vertical
position.
2.
Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob
to the left and hold it. Raise the frame until the catch is
past the latch pin. Slowly release the latch knob.
Make
sure that the catch is securely held by the latch pin.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 85° Fahrenheit.
If you purchase the optional chest pulse sensor, follow the steps below to install the receiver included
with the chest pulse sensor.
1.
Make sure that the power cord is unplugged.
Remove the 3/4” Screw (33) and the Access Door
(105) from the Console Back (104).
2.
Connect the wire on the receiver (A) to the indicated
wire extending from the Console Back (104). Remove
the paper from the adhesive pad on the back of the
receiver.
Hold the receiver so the small cylinder is
near the lower edge of the receiver and is facing
the Console Back as shown.
Firmly press the re-
ceiver onto the indicated corner of the Access Door
(105). Note: If there are two screws included with the
chest pulse sensor and two plastic posts on the inside
of the Access Door, attach the receiver to the plastic
posts on the Access Door with the two screws.
3.
Make sure that no wires are pinched.
Reattach the Access Door (105) with the 3/4” Screw (33). The other
wires included with the receiver may be discarded.
Latch
Knob
Pin
Catch
Closed
23
A
104
105
Cylinder
33
Wire