RCA HD61LPW175 User Manual - Page 42

Volume Punchthrough Feature

Get RCA HD61LPW175 PDF manuals and user guides View all RCA HD61LPW175 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Using the Remote Control Volume Punchthrough Feature You may find this feature helpful if you've connected your devices to an audio/video receiver (A/V receiver) or amplifier, but you want to use the TV's remote control to operate the volume for a device that is connected to the audio/video receiver. An example follows: Let's say you've connected your DVD player to your audio/video receiver. You've also programmed your TV remote control to operate your DVD player. Since the DVD player gets its volume through the audio/video receiver, you would have to bounce back and forth between two remote controls: the A/V receiver's remote to adjust the volume and the TV's remote control to operate the DVD player. The Volume Punchthrough feature eliminates the need for you to use two remote controls and saves a button press when you're using the TV remote to adjust the volume. In effect, you are telling the TV remote to retrieve and send volume commands from the a/v receiver whenever the TV remote is in DVD mode. Therefore, after you've successfully set up the Volume Punchthrough feature, whenever the TV remote is in DVD mode (press the DVD button) and you want to adjust the volume, you only have to press the VOL + or VOL- buttons. Follow the instructions below to set up Volume Punchthrough. 1. IMPORTANT: First, you must program the AUDIO button on the TV's remote control to operate your audio receiver or amplifier. Go to page 28 for instructions. If you can't program this remote to operate your audio receiver, Volume Punchthrough won't work. 2. While setting up Volume Punchthrough, it's best to point the remote away from devices. 3. Decide which mode the remote will be in when the volume from the audio receiver "punches through." The mode will be one of the device buttons (TV, DVD, SAT/CAB, VCR, or AUX). 4. Press and hold the VOL- button. Keep pressing VOL- while you press and release the device button you chose in step 3 (TV, DVD, SAT/CAB, or AUX). 5. Press and release the AUDIO button since the sound will be coming from the audio/video receiver. Release the VOL- button. 6. Now, test it by turning on your audio receiver or amplifier. 7. Turn on the device that is connected to the audio/video receiver or amplifier (a DVD player, for example). 8. Put the TV's remote in DVD mode by pressing the DVD button, and play a disc. 9. Press VOL+ or VOL-. The volume from the audio receiver should increase or decrease accordingly. Deleting ALL Volume Punchthrough Commands To delete all programmed Volume Punchthrough settings and return the remote control back to the factory defaults, press and hold the VOL- button (the device button of the Volume Punchthrough lights). While holding the VOL- button, enter the code, 000, using the number buttons. All device buttons turn on for 2 seconds and then turn off. The remote returns to the factory settings. Note: If an invalid button is pressed, all device buttons blink 4 times and turn off. At this point, you must start over. 40 Chapter 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
40
Chapter 2
Using the Remote Control
Volume Punchthrough Feature
You may find this feature helpful if you’ve connected your devices to an audio/video receiver
(A/V receiver) or amplifier, but you want to use the TV’s remote control to operate the volume for
a device that is connected to the audio/video receiver. An example follows:
Let’s say you’ve connected your DVD player to your audio/video receiver. You’ve also
programmed your TV remote control to operate your DVD player. Since the DVD player gets its
volume through the audio/video receiver, you would have to bounce back and forth between two
remote controls: the A/V receiver’s remote to adjust the volume and the TV’s remote control to
operate the DVD player.
The Volume Punchthrough feature eliminates the need for you to use two remote controls and
saves a button press when you’re using the TV remote to adjust the volume. In effect, you are
telling the TV remote to retrieve and send volume commands from the a/v receiver whenever the
TV remote is in DVD mode.
Therefore, after you’ve successfully set up the Volume Punchthrough feature, whenever the
TV remote is in DVD mode (press the DVD button) and you want to adjust the volume, you
only have to press the VOL + or VOL- buttons. Follow the instructions below to set up Volume
Punchthrough.
1.
IMPORTANT: First, you must program the AUDIO button on the TV’s remote control to
operate your audio receiver or amplifier. Go to page 28 for instructions. If you can’t program
this remote to operate your audio receiver, Volume Punchthrough won’t work.
2.
While setting up Volume Punchthrough, it’s best to point the remote away from devices.
3.
Decide which mode the remote will be in when the volume from the audio receiver “punches
through.” The mode will be one of the device buttons (TV, DVD, SAT/CAB, VCR, or AUX).
4.
Press and hold the VOL- button. Keep pressing VOL- while you press and release the device
button you chose in step 3 (TV, DVD, SAT/CAB, or AUX).
5.
Press and release the AUDIO button since the sound will be coming from the audio/video
receiver. Release the VOL- button.
6.
Now, test it by turning on your audio receiver or amplifier.
7.
Turn on the device that is connected to the audio/video receiver or amplifier (a DVD player,
for example).
8.
Put the TV’s remote in DVD mode by pressing the DVD button, and play a disc.
9.
Press VOL+ or VOL-. The volume from the audio receiver should increase or decrease
accordingly.
Deleting ALL Volume Punchthrough Commands
To delete all programmed Volume Punchthrough settings and return the remote control back
to the factory defaults, press and hold the VOL- button (the device button of the Volume
Punchthrough lights). While holding the VOL- button, enter the code,
000
, using the number
buttons. All device buttons turn on for 2 seconds and then turn off. The remote returns to the
factory settings.
Note:
If an invalid button is pressed, all device buttons blink 4 times and turn off. At this
point, you must start over.