Reebok Rl545 Elliptical English Manual - Page 8

Attach the Right Upper Body Arm 6 in

Get Reebok Rl545 Elliptical PDF manuals and user guides View all Reebok Rl545 Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

9. Insert the Pivot Axle (21) into the Upright (2), and center the Pivot Axle. Apply a generous amount of the included grease to both ends of the Pivot Axle and to the flat side of an Upright Bushing (20). Identify the Left Upper Body Arm (5), which is marked with a decal. Insert the Upright Bushing (20) into an Upright Spacer (19). Turn the Upright Spacer so that the semicircular cutout is at the top, and slide the Upright Spacer onto the post on the Left Upper Body Arm. Slide the Left Upper Body Arm (5) onto the Pivot Axle (21). Attach a Pivot Spacer (17) to the Left Upper Body Arm with an M4 x 16mm Screw (82). Turn a Pivot Endcap (16) so that the rectangular cutout is at the bottom. Using a rubber mallet, tap the Pivot Endcap into the Pivot Spacer. Slide a Small M8 Washer (71) onto an M8 x 19mm Shoulder Screw (86), and finger tighten the Shoulder Screw into the Pivot Axle (21). Attach the Right Upper Body Arm (6) in the same manner. Tighten both M8 x 25mm Patch Screws (73). 10. Apply a small amount of grease to the axle on the left Crank Arm (40). Identify the Left Pedal Leg (28), which is marked with a decal. Slide the Left Pedal Leg onto the axle on the left Crank Arm (40). Slide a Wave Washer (91) and a Large M8 Washer (70) onto an M8 x 25mm Patch Screw (73), and tighten the Patch Screw into the axle. Make sure that the Wave Washer is on the end of the axle before tightening the Patch Screw. Snap a Pedal Cushion (74) around the Left Pedal Leg (28) onto a Cushion Bracket (46). Make sure that the arrow on the Pedal Cushion is pointing to one of the numbers on the Left Pedal Leg and that the number shows through the window in the Cushion Bracket. Assemble the Right Pedal Leg (not shown) in the same way. 11. Identify the Left Pedal Arm (33), which is marked with a decal. Attach the Left Pedal (35) to the Left Pedal Arm with two M6 x 20mm Patch Screws (75) as shown. Attach the Right Pedal (not shown) to the Right Pedal Arm (not shown) in the same way. 9 5 17 16 71 86 82 2 20 21 19 Post Grease 6 10 74 Grease 28 40 46 Window 91 73 70 11 75 35 33 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
8
10. Apply a small amount of grease to the axle on the
left Crank Arm (40).
Identify the Left Pedal Leg (28), which is marked
with a decal. Slide the Left Pedal Leg onto the axle
on the left Crank Arm (40). Slide a Wave Washer
(91) and a Large M8 Washer (70) onto an M8 x
25mm Patch Screw (73), and tighten the Patch
Screw into the axle.
Make sure that the Wave
Washer is on the end of the axle before tightening
the Patch Screw.
Snap a Pedal Cushion (74) around the Left Pedal Leg
(28) onto a Cushion Bracket (46). Make sure that the
arrow on the Pedal Cushion is pointing to one of the
numbers on the Left Pedal Leg and that the number
shows through the window in the Cushion Bracket.
Assemble the Right Pedal Leg (not shown) in the
same way.
11. Identify the Left Pedal Arm (33), which is marked
with a decal. Attach the Left Pedal (35) to the Left
Pedal Arm with two M6 x 20mm Patch Screws (75)
as shown.
Attach the Right Pedal (not shown) to the Right
Pedal Arm (not shown) in the same way.
28
40
Grease
70
73
74
91
46
Window
10
9.
Insert the Pivot Axle (21) into the Upright (2), and
center the Pivot Axle. Apply a generous amount of
the included grease to both ends of the Pivot Axle
and to the flat side of an Upright Bushing (20).
Identify the Left Upper Body Arm (5), which is
marked with a decal. Insert the Upright Bushing (20)
into an Upright Spacer (19). Turn the Upright
Spacer so that the semicircular cutout is at the top,
and slide the Upright Spacer onto the post on the
Left Upper Body Arm.
Slide the Left Upper Body Arm (5) onto the Pivot
Axle (21). Attach a Pivot Spacer (17) to the Left
Upper Body Arm with an M4 x 16mm Screw (82).
Turn a Pivot Endcap (16) so that the rectangular
cutout is at the bottom. Using a rubber mallet, tap
the Pivot Endcap into the Pivot Spacer.
Slide a Small M8 Washer (71) onto an M8 x 19mm
Shoulder Screw (86), and finger tighten the Shoulder
Screw into the Pivot Axle (21).
Attach the Right Upper Body Arm (6) in the
same manner.
Tighten both M8 x 25mm Patch
Screws (73).
19
17
16
82
86
71
6
Grease
Post
5
21
20
2
9
11
75
35
33