Reebok Rst 250 English Manual - Page 10

Warning, Adjustments

Get Reebok Rst 250 PDF manuals and user guides View all Reebok Rst 250 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

ADJUSTMENTS The weight bench is designed to be used with your own weight set (not included). The steps below explain how the weight bench can be adjusted. See EXERCISE GUIDELINES on page 11 for important exercise information and refer to the accompanying exercise guide to see the correct form for several exercises. Make sure all parts are properly tightened each time you use the weight bench. Replace any worn parts immediately. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents. ADJUSTING THE BACKREST The Backrest (8) can be used in eight different positions. To adjust the Backrest, hold the Backrest up and pull the Backrest Adjustment Knob (30) out as far as it will go. Move the Backrest to the desired position and insert the Knob into an adjustment hole in the Backrest Bracket (9). 15 WARNING: When adjusting the position of the Backrest (8), first remove all weight from the Leg Lever (15). Make sure that the Backrest Adjustment Knob (30) is fully inserted through the Backrest Bracket (9). 8 30 9 Adjustment Hole ADJUSTING THE WEIGHT REST AND WEIGHT SPOTTER Before beginning an exercise, move the Weight Rests (12, 44 [not shown]) and the Weight Spotters (11, 45 [not shown]) to sets of holes in the Uprights (4) that are best suited for that exercise. Do this by turning the Adjustment Knobs (18) counterclockwise until loose. Pull the Knobs out and slide the Weight Rests or the Weight Spotters to the desired height. Snap the Knobs into the adjustment holes in the Uprights and turn the Knobs clockwise until tight. The selected holes for the Weight Spotters (11, 45 [not shown]) should represent the lowest point to which you want the barbell to go during the exercise. The selected holes for the Weight Rests (12, 44 [not shown]) should be at a comfortable height for lifting and replacing the barbell. Perform the exercise as shown on the accompanying exercise guide. Note: Make sure the Adjustment Knobs (18) are fully tightened. WARNING: Always set both Weight Rests (12, 44) at the same height and both Weight Spotters (11, 45) at the same height. 4 12 18 18 Adjustment Hole 11 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
10
ADJUSTING THE BACKREST
The Backrest (8) can be used in eight different posi-
tions. To adjust the Backrest, hold the Backrest up
and pull the Backrest Adjustment Knob (30) out as far
as it will go. Move the Backrest to the desired posi-
tion and insert the Knob into an adjustment hole in
the Backrest Bracket (9).
ADJUSTING THE WEIGHT REST AND WEIGHT
SPOTTER
Before beginning an exercise, move the Weight
Rests
(12, 44 [not shown]) and the Weight Spotters
(11, 45 [not shown]) to sets of holes in the Uprights
(4) that are best suited for that exercise. Do this by
turning the Adjustment Knobs (18) counterclockwise
until loose. Pull the Knobs out and slide the Weight
Rests or the Weight Spotters to the desired height.
Snap the Knobs into the adjustment holes in the
Uprights and turn the Knobs clockwise until tight.
The selected holes for the Weight Spotters (11, 45 [not
shown]) should represent the lowest point to which you
want the barbell to go during the exercise. The select-
ed holes for the Weight Rests (12, 44 [not shown])
should be at a comfortable height for lifting and replac-
ing the barbell. Perform the exercise as shown on the
accompanying exercise guide.
Note: Make sure the
Adjustment Knobs (18) are fully tightened.
WARNING:
When adjusting the
position of the Backrest (8), first remove all
weight from the Leg Lever (15). Make sure that
the Backrest Adjustment Knob (30) is fully
inserted through the Backrest Bracket (9).
4
11
12
18
18
The weight bench is designed to be used with your own weight set (not included). The steps below explain how
the weight bench can be adjusted. See EXERCISE GUIDELINES on page 11 for important exercise information
and refer to the accompanying exercise guide to see the correct form for several exercises.
Make sure all parts are properly tightened each time you use the weight bench. Replace any worn parts immediate-
ly. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
8
9
30
15
Adjustment Hole
Adjustment Hole
ADJUSTMENTS
WARNING:
Always set both
Weight Rests (12, 44) at the same height and
both Weight Spotters (11, 45) at the same
height.