Ryobi A99DLK3 Operation Manual - Page 1
Ryobi A99DLK3 Manual
View all Ryobi A99DLK3 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
WOOD DOOR LOCK INSTALLATION KIT A99DLK3 WARNING: To reduce the risk of injury, do not attempt to use this product until you have read thoroughly and understand completely this operator's manual and the operator's manual for any power tools used. PACKING LIST See Figure 1. Bracket Auto-strike Locator 1 in. Spade Bit 2-1/8 in. Carbon Hole Saw Arbor with Brad Point Pilot Bit PH2/SL8-10 Double Ended Bit 3/32 in. Drill Bit 1/8 in. Brad Point Bit TOOLS NEEDED AC Power Drill or DC Drill 18 Volts or more Pencil APPLICATIONS You may use this tool for the following purpose: Installing lock sets and dead bolts easily and accurately without measuring. INSTRUCTIONS See Figures 2 - 7. Read hardware instructions to find backset location. Select desired door thickness by inserting the auto-strike locator into the door thickness slots, left for 1-3/8 in. or right for 1-3/4 in. backset. Check that the auto-strike locator is securely locked in place. Position bracket on door using the auto-strike locator. Line up locator with the center of the strike plate in the door jamb by shutting the door and positioning the bracket until it falls into the strike plate. Using a pencil, mark the desired backset location (shown on instructions included with door hardware) and latch bore location using bracket hole locators. Remove bracket from door. Assemble hole saw Remove arbor nut from arbor with pilot bit. Insert arbor with pilot bit through hole saw lining up flats. Securely tighten arbor nut onto arbor with pilot bit, see figure 5. Follow drill manual instructions to install hole saw into chuck. Using hole saw, drill cross bore hole first. For a straight hole, be sure drill is at a right angle to the door so hole saw enters the wood evenly. Drill from one side until pilot bit shows on opposite side of door. Drill on opposite side, lining up pilot bit hole with pilot bit. Meet the two holes in the center of door. Using the 1 in. spade bit, drill latch bore. Keep drill at a right angle to door flat to ensure straight hole. Follow instructions included with door hardware for installation. Use included drill bits and double ended bit to install hardware. If installing a lock set with a rectangular, flush mounted strike plate, use the RYOBI Door Latch Installation Kit (Model# A99LM2) Fig. 1 A E D F H B C G A - Bracket (support, soporte) B - Auto-strike Locator (pied de positionnement automatique, indicador de posición con golpe automático) C - 1 in. spade bit [embout à trois, pointes de 25,4 mm (1 po), broca de pala de 25,4 mm (1 pulg.)] D - 2-1/8 in. hole saw [scie cloche au carbone de 53, 98 mm (2-1/8 po), sierra de perforación de carbono de 53,98 mm (2-1/8 pulg.)] E - Arbor with pilot bit and arbor nut (embout avec mèche pilote et écrou d'embout, mandril con broca piloto y tuerca del árbol) F - 1/8 in. brad point drill bit [embout de 3,18 mm (1/8 po), punta de destornillador de 3,18 mm (1/8 pulg.)] G - 3/32 in. drill bit [embout de 2,4 mm (3/32 po), punta de destornillador de 2,4 mm (3/32 pulg.)] H - PH2/SL8-10 double ended bit (embout double 8-10SL nº 2, broca de doble extremo 8-10SL N.º 2) Fig. 2 A B A - 1-3/8 in. door thickness [épaisseur porte 34,925 mm (1-3/8 po), espesor de la puerta 34,925 mm (1-3/8 in)] B - 1-3/4 in. door thickness (épaisseur porte 44,45 mm (1-3/4 po), espesor de la puerta 44,45 mm (1-3/4 in)) Fig. 3 D A E D C D B D A - Cross bore (trou transversal, orificio transversal) B - Backset (appui, distancia al centro del picaporte) C - Latch bore (trou du loquet, orificio del pestillo) D - Center mark (point central, marca de centro) E - Door thickness (épaisseur de porte, espesor de la puerta) Fig. 4 D B C F A A - Bracket (support, soporte) B - Auto-strike locator (localisateur à martelage automatique, indicador de posición con golpe automático) C - Backset locator (pied de positionnement pour distance de retrait, Indicador de ubicación de la parte trasera) D - Strike plate (gâche, placa receptora de impactos) F - Latch bore locator (localisateur à trou du loquet, indicador de posición orificio del pestillo) Fig. 5 A A - Mark with pencil (marquer avec un crayon, marque con un lápiz) Fig. 6 A B C E D A - Arbor with pilot bit and arbor nut (arbre avec embout pilote et écrou d'arbre, mandril con broca piloto y tuerca del árbol) B - Carbon hole saw (scie cloche au carbone, sierra de perforación de carbono ) C - Arbor with pilot bit (arbre avec embout pilote, mandril con broca piloto) D - Arbor nut (écrou d'arbre, tuerca del árbol) E - Hole saw assembly (assemblage de la scie-cloche, conjunto de la sierra de perforación) Fig. 7 B A A - To drill cross bore (pour percer le trou transversal, para perforar orificio transversal) B - To drill latch bore (pour percer le trou du loquet, para perforar orificio de pestillo)