Ryobi AR2016G Operation Manual - Page 1

Ryobi AR2016G Manual

Get Ryobi AR2016G PDF manuals and user guides View all Ryobi AR2016G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

To remove a one-way screw: Fig. 2  Insert the hex key into the hole in the guide sleeve A and loosen the set screw.  Select the appropriate driving bit. OPERATOR'S MANUAL ONE-WAY SCREW INSTALLER/REMOVER  Place the tip of the driving bit onto the head of the one-way screw. B B AR2016G  Slide the guide sleeve over the driving bit and onto the drilling surface. WARNING: NOTE: Ensure the guide sleeve is flush against the C surface. C To reduce the risk of injury, do not attempt to use  Place the hex key into the hole in the guide sleeve this product until you have read thoroughly and and tighten the set screw to secure the sleeve in understand completely this operator's manual and place. the operator's manual for any power tools used. Al-  Using a drill (not included), rotate the bit ways wear eye protection with side shields marked counterclockwise slowly while keeping constant to comply with ANSI Z87.1. Ensure compatibility pressure on drill to loosen and remove the screw. and fit before using this accessory. Do not use this accessory if a part is damaged or missing. ONE WORLD TECHNOLOGIES, INC. P.O. Box 1288, Anderson, SC 29622 PACKING LIST 1-800-525-2579 • www.ryobitools.com See Figure 1. Fig. 1 D Hex Key, Driving Bit (for screws #4-8), Driving Bit (for screws #10-12), Driving Bit (for screws #14 and up), and Guide Sleeve A A C INSTALLING/REMOVING ONE-WAY SCREWS C See Figure 2. To install a one-way screw:  Install the appropriate bit into a drill (not included). NOTE: This product can be installed onto any drill (not included) with a 1/4 in. or larger chuck. A - Guide sleeve (douille de guidage, manga guía)  Place the tip of the driving bit onto the head of the B B - Driving bit (embout de vissage, punta para atornillar) one-way screw. A - Hex key (clé hexagonale, llave hexagonal) C - One-way screw (vis à sens unique, tornillo de dirección  Rotate the bit clockwise to install the screw into the B - Driving bits (embouts de vissage, puntas para atornillar) única) drilling surface. C - Guide sleeve (douille de guidage, manga guía) D - Hex key (clé hexagonale, llave hexagonal)

  • 1
  • 2
OPERATOR’S MANUAL
ONE-WAY SCREW INSTALLER/REMOVER
AR2016G
ONE WORLD TECHNOLOGIES, INC.
P.O. Box 1288, Anderson, SC 29622
1-800-525-2579 •
www.ryobitools.com
A
B
B
C
C
B
C
A - Hex key (clé hexagonale, llave hexagonal)
B - Driving bits (embouts de vissage, puntas para atornillar)
C - Guide sleeve (douille de guidage, manga guía)
A - Guide sleeve (douille de guidage, manga guía)
B - Driving bit (embout de vissage, punta para atornillar)
C - One-way screw (vis à sens unique, tornillo de dirección
única)
D - Hex key (clé hexagonale, llave hexagonal)
Fig. 1
Fig. 2
A
WARNING:
To reduce the risk of injury, do not attempt to use
this product until you have read thoroughly and
understand completely this operator’s manual and
the operator’s manual for any power tools used. Al-
ways wear eye protection with side shields marked
to comply with ANSI Z87.1. Ensure compatibility
and fit before using this accessory. Do not use this
accessory if a part is damaged or missing.
PACKING LIST
See Figure 1.
Hex Key, Driving Bit (for screws #4-8), Driving Bit (for
screws #10-12), Driving Bit (for screws #14 and up),
and Guide Sleeve
INSTALLING/REMOVING ONE-WAY
SCREWS
See Figure 2.
To install a one-way screw:
Install the appropriate bit into a drill (not included).
NOTE:
This product can be installed onto any drill
(not included) with a 1/4 in. or larger chuck.
Place the tip of the driving bit onto the head of the
one-way screw.
Rotate the bit clockwise to install the screw into the
drilling surface.
To remove a one-way screw:
Insert the hex key into the hole in the guide sleeve
and loosen the set screw.
Select the appropriate driving bit.
Place the tip of the driving bit onto the head of the
one-way screw.
Slide the guide sleeve over the driving bit and onto
the drilling surface.
NOTE:
Ensure the guide sleeve is flush against the
surface.
Place the hex key into the hole in the guide sleeve
and tighten the set screw to secure the sleeve in
place.
Using a drill (not included), rotate the bit
counterclockwise slowly while keeping constant
pressure on drill to loosen and remove the screw.
C
D
A