Ryobi RTS12 Operation Manual - Page 23

How To Make A Jig For Rip Cutting

Get Ryobi RTS12 PDF manuals and user guides View all Ryobi RTS12 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

OPERATION CUTTING AIDS See Figure 19. Push sticks are devices that may be used for pushing a workpiece through the blade in any rip cut. When making non-through cuts or ripping narrow stock, always use a push stick, push block, and/or featherboard so your hands do not come within 3 inches of the saw blade. They can be made in various sizes and shapes from scrap wood and used in a specific project. The stick must be narrower than the workpiece, with a 90˚ notch in one end and shaping for a grip on the other end. A push block has a handle fastened by recessed screws from the underside. Use push blocks for narrow cuts and all non-through cuts. CAUTION: Be sure the screws in a push block are recessed to avoid damaging the saw or workpiece. AUXILIARY FENCE An auxiliary fence is a device used to close the gap between the rip fence and the saw table. Always make and use and auxiliary fence when ripping material 1/8 in. or thinner. HOW TO MAKE AND ATTACH AN AUXILIARY FENCE (FOR RIP CUTTING THIN WORKPIECE) See Figure 20. Rip fence holes are used to secure an auxiliary fence which requires a piece of wood 3/4 in. thick, 3-1/2 in. wide, and 18-1/2 in. long to make. To attach the auxiliary fence to the rip fence:  Place the wood against the rip fence and resting firmly on the saw table.  From the back side of the rip fence, secure the wood to the fence using 1-1/2 in. wood screws. HOW TO MAKE A JIG (FOR RIP CUTTING NARROW WORKPIECE) See Figure 21. If ripping a narrow workpiece places the hands too close to the blade, it will be necessary to make and use a jig. To make a jig:  Attach a handle to a long, straight piece of wood and secure from the underside using recessed screws.  Cut an L-shaped stop in the side of the jig. To use a jig:  Position the workpiece flat on the table with the edge flush against the jig and against the stop.  Holding the jig handle and using a push block, make the rip cut as described on page 31 later in this section. 23 - English PUSH STICKS PUSH BLOCKS Fig. 19 181-811/22inin. . 3/41/i2nin.. 4 1/4 3in-.1/2 in. Fig. 20 STOP JIG HANDLE JIG Fig. 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
23 - English
OPERATION
CUTTING AIDS
See Figure 19.
Push sticks are devices that may be used for pushing a
workpiece through the blade in any rip cut. When making
non-through cuts or ripping narrow stock, always use a
push stick, push block, and/or featherboard so your hands
do not come within 3 inches of the saw blade. They can be
made in various sizes and shapes from scrap wood and
used in a specific project. The stick must be narrower than
the workpiece, with a 90˚ notch in one end and shaping for
a grip on the other end.
A push block has a handle fastened by recessed screws
from the underside. Use push blocks for narrow cuts and
all non-through cuts.
CAUTION:
Be sure the screws in a push block are recessed to avoid
damaging the saw or workpiece.
AUXILIARY FENCE
An auxiliary fence is a device used to close the gap between
the rip fence and the saw table. Always make and use and
auxiliary fence when ripping material 1/8 in. or thinner.
HOW TO MAKE AND ATTACH AN AUXILIARY
FENCE (FOR RIP CUTTING THIN WORKPIECE)
See Figure 20.
Rip fence holes are used to secure an auxiliary fence which
requires a piece of wood 3/4 in. thick, 3-1/2 in. wide, and
18-1/2 in. long to make.
To attach the auxiliary fence to the rip fence:
Place the wood against the rip fence and resting firmly
on the saw table.
From the back side of the rip fence, secure the wood to
the fence using 1-1/2 in. wood screws.
HOW TO MAKE A JIG (FOR RIP CUTTING
NARROW WORKPIECE)
See Figure 21.
If ripping a narrow workpiece places the hands too close to
the blade, it will be necessary to make and use a jig.
To make a jig:
Attach a handle to a long, straight piece of wood and
secure from the underside using recessed screws.
Cut an L-shaped stop in the side of the jig.
To use a jig:
Position the workpiece flat on the table with the edge
flush against the jig and against the stop.
Holding the jig handle and using a push block, make the
rip cut as described on page 31 later in this section.
PUSH BLOCKS
PUSH STICKS
Fig. 19
Fig. 20
Fig. 21
JIG
JIG
HANDLE
STOP
18-1/2 in.
3/4 in.
3-1/2 in.