Samsung HP-P5071 User Manual (user Manual) (ver.1.0) (English) - Page 12

Fixing the PDP panel to the wall attachment panel bracket - plasma

Get Samsung HP-P5071 PDF manuals and user guides View all Samsung HP-P5071 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Wall Installation Instructions Fixing the PDP panel to the wall attachment panel bracket 1 Remove the screws from the back of the PDP. 2 Connect insulation holders to screws (see the illustration below). • If you are uncertain about installation, hire a specialist to install the wall mount bracket. • Be sure to check that the insulation holders are completely secured on both the left and right side after hanging the PDP on the wall mount bracket. • Be careful to avoid getting your fingers caught during installation. • Make sure the wall attachment panels are tightened. Otherwise the PDP may fall. 3 Tighten the screws of the insulation holders to the back of the PDP. 4 Put the 4 insulation holders on the PDP in the grooves of the wall mount bracket and pull down on the PDP (Œ) to secure it to the wall mount bracket (´). Tighten the screws as shown (ˇ) so that the PDP cannot be separated from wall mount bracket. PDP panel ˇ Œ ´ Wall attachment panel bracket Wall Note • A 5 inch(12.7 cm) gap is needed between the back of the Plasma TV and the wall. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
1
Remove the screws from the back of the PDP.
2
Connect insulation holders to screws (see the illustration below).
• If you are uncertain about installation, hire a specialist to install the wall mount bracket.
• Be sure to check that the insulation holders are completely secured on both the left
and right side after hanging the PDP on the wall mount bracket.
• Be careful to avoid getting your fingers caught during installation.
• Make sure the wall attachment panels are tightened. Otherwise the PDP may fall.
Note
•
A 5 inch(12.7 cm) gap is needed between the back of the Plasma TV and the wall.
Wall Installation Instructions
12
Fixing the PDP panel to the wall attachment panel bracket
3
Tighten the screws of the insulation
holders to the back of the PDP.
4
Put the 4 insulation holders on the PDP
in the grooves of the wall mount
bracket and pull down on the PDP (
Œ
)
to secure it to the wall mount bracket
(
´
). Tighten the screws as shown (
ˇ
)
so that the PDP cannot be separated
from wall mount bracket.
PDP panel
Wall attachment panel
bracket
Wall
Œ
´
ˇ