Samsung HP-P5091 User Manual (user Manual) (ver.1.0) (English) - Page 80

Problem, Possible Solution, Solution: Set the Remote Control to the TV Mode

Get Samsung HP-P5091 PDF manuals and user guides View all Samsung HP-P5091 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

PDP (Continued) Problem There is no signal in a digital channel, and messages "Searching for Signals" followed by "No Signal" appear. Cause: Channels have been stored using Auto Memorize but the broadcasting companies are not sending the corresponding signals. Or External Input has been selected but there is no signal. The message "Not supported sound format" appears. Cause: Digital Audio rather than AC-3 (such as DTS, MPEG-1 or MPEG-2) was entered for Audio when SPDIF Input is selected in the Component Mode resulting in displaying this message with no picture. The picture quality is poor in the Component Mode despite setting 480p. Cause: To enable the wireless signal transmission for 480p input, it is converted to 480i before MPEG Encoding. After selecting the STB Mode of the Remote Control, AV Center does not respond to the Remote Control. Cause: The Remote Control of AV Center only turns power ON and OFF, but cannot respond to other Remote Control keys. The message "Not available in the current mode." appears. Cause: Input of unavailable function keys (e.g. trying to switch a channel in External Input mode) may cause the message to appear. 80 Possible Solution Solution: Select an alternative channel or switch the external input source. Solution: AV Center cannot handle the Audio Mode except AC-3. Switch the input to AC-3, or alternatively select Set-Up in the Menu, move to Sound In/Out then switch Digital Input to Lt/Rt. Note: Digital Audio inputs except AC-3 might cause a severe damage to the system. Please use Dolby Digital as a digital audio input. Solution: MPEG Encoding of 480p is not possible in the current consumer electronics technology as it is, so viewing the original 480p picture quality is limited. Solution: Set the Remote Control to the TV Mode and perform all controls on the PDP. Solution: Please try to use other menu keys that are available.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
80
PDP
(Continued)
Problem
Possible Solution
There is no signal in a digital chan-
nel, and messages “Searching for
Signals” followed by “No Signal”
appear.
Cause: Channels have been stored
using Auto Memorize but the
broadcasting companies are not
sending the corresponding signals.
Or External Input has been selected
but there is no signal.
Solution: Select an alternative channel or switch the
external input source.
The message “Not supported sound
format” appears.
Cause: Digital Audio rather than
AC-3 (such as DTS, MPEG-1 or
MPEG-2) was entered for Audio
when SPDIF Input is selected in the
Component Mode resulting in
displaying this message with no
picture.
Solution: AV Center cannot handle the Audio Mode
except AC-3. Switch the input to AC-3, or alternatively
select Set-Up in the Menu, move to Sound In/Out then
switch Digital Input to Lt/Rt.
Note: Digital Audio inputs except AC-3 might cause a
severe damage to the system. Please use Dolby Digital
as a digital audio input.
The picture quality is poor in the
Component Mode despite setting
480p.
Cause: To enable the wireless signal
transmission for 480p input, it is
converted to 480i before MPEG
Encoding.
Solution: MPEG Encoding of 480p is not possible in
the current consumer electronics technology as it is,
so viewing the original 480p picture quality is limited.
After selecting the STB Mode of the
Remote Control, AV Center does not
respond to the Remote Control.
Cause: The Remote Control of AV
Center only turns power ON and
OFF, but cannot respond to other
Remote Control keys.
Solution: Set the Remote Control to the TV Mode and
perform all controls on the PDP.
The message “Not available in the
current mode.” appears.
Cause: Input of unavailable function
keys (e.g. trying to switch a channel
in External Input mode) may cause
the message to appear.
Solution: Please try to use other menu keys that are
available.