Samsung RF268ABBP User Manual (user Manual) (ver.1.0) (English) - Page 13

coupler

Get Samsung RF268ABBP PDF manuals and user guides View all Samsung RF268ABBP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

01 SETTING UP REATTACHING THE REFRIGERATOR DOORS 4. C onnect the dispenser door tube ( 5 ) and then insert a clip on the coupler with pulling tube. 3 4 Connect the connector ( 4 ) on the left side door and two connectors ( 3 ) at each side of the top cap. The clip is enveloped inside of the top cap. 3 5 dispenser door tube The dispenser door tube ( 5 ) must be fully inserted to the marked CAUTION line to prevent water leakage from the dispenser. coupler 5. P osition the top table ( 2 ) in place. Insert and tighten the 3 screws into the top table with a philips screw driver(+). With the doors open, reinsert the cap top table ( 1 ) and close the doors. 2 When reattaching the top table, make sure that the wires are not pressed or damaged by the hinge cover. After assembling, close the doors and check 1 to see whether the doors have gaps between gaskets or are tilted. If you see a gap or tilt please refer to "Adjusting the doors" on page 15. Setting up _13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Setting up
_13
01 SETTING UP
5. Position the top table (
2
) in place. Insert and tighten
the 3 screws into the top table with a philips screw
driver(+). With the doors open, reinsert the cap top
table (
1
) and close the doors.
REATTACHING THE REFRIGERATOR DOORS
1
2
3
3
4
5
coupler
dispenser door tube
The dispenser door tube (
5
) must be fully inserted to the marked
line to prevent water leakage from the dispenser.
CAUTION
4. Connect the dispenser door tube (
5
) and then
insert a clip on the coupler with pulling tube.
Connect the connector (
4
) on the left side door
and two connectors (
3
) at each side of the top
cap.
The clip is enveloped inside of the top cap.
When reattaching the top table, make sure that
the wires are not pressed or damaged by the
hinge cover.
After assembling, close the doors and check
to see whether the doors have gaps between
gaskets or are tilted. If you see a gap or tilt
please refer to “Adjusting the doors” on page 15.