Samsung RF268ABBP User Manual (user Manual) (ver.1.0) (English) - Page 9

Removing The Refrigerator Doors, Setting Up The Refrigerator - part list

Get Samsung RF268ABBP PDF manuals and user guides View all Samsung RF268ABBP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

SETTING UP THE REFRIGERATOR Now that you have your new Refrigerator installed in place, you are ready to set up and enjoy the features and functions of the appliance. By completing the following steps, your Refrigerator should be fully operational. 1. P lace the Refrigerator in an appropriate location with reasonable clearance between it and the wall. Refer to installation instructions in this manual. 2. Once the Refrigerator is plugged in, make sure the interior light comes on when you open the doors. 3. S et the Temperature control to the coldest temperature and wait for an hour. The Freezer will get slightly chilled and the motor will run smoothly. 4. A fter powering the Refrigerator, it will take a few hours to reach the appropriate temperature. You can store food and drinks in the Refrigerator after the temperature is sufficiently cool. Check the accessories listed below. 01 SETTING UP Water filter Hex wrench Fastener Required Tools (Not provided) Compression fitting Compression nut Clip fitting lock(red) Philips screwdriver(+) Flat-blade screwdriver(-) Socket wrench (7/16") Pliers Allen wrench(3/16") REMOVING THE REFRIGERATOR DOORS Some installations require door removal to transport the Refrigerator to its final location. Do not remove the door/drawer if it is not needed. Before removing the door/drawer, make sure you read following items. Disconnect power to the Refrigerator before removing the door or drawer. WARNING • Be careful not to drop, damage or scratch the door/drawer while removing them. • Be careful not to get injured while removing the door/drawer. • Reattach the door/drawer properly to avoid: - Moisture from air leakage. - Uneven door alignment. - Wasting energy due to improper door seal. Disassemble the Refrigerator doors Be careful not to drop and scratch the doors while removing the WARNING doors. Disassemble the Refrigerator doors 2 1. With the door opened, remove the cap top table ( 1 ) with a flat-blade screwdriver(-), and close the door. Remove the 3 screws holding down the top table ( 2 ) and 1 remove it. Setting up _9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Setting up
_9
01 SETTING UP
REMOVING THE REFRIGERATOR DOORS
SETTING UP THE REFRIGERATOR
Now that you have your new Refrigerator installed in place, you are ready to set up and enjoy the features and
functions of the appliance. By completing the following steps, your Refrigerator should be fully operational.
1. Place the Refrigerator in an appropriate location with reasonable clearance between it and the wall.
Refer to installation instructions in this manual.
2. Once the Refrigerator is plugged in, make sure the interior light comes on when you open the doors.
3. Set the Temperature control to the coldest temperature and wait for an hour. The Freezer will get slightly
chilled and the motor will run smoothly.
4. After powering the Refrigerator, it will take a few hours to reach the appropriate temperature. You can
store food and drinks in the Refrigerator after the temperature is sufficiently cool.
Philips screwdriver(+)
Flat-blade screwdriver(-)
Socket wrench (7/16”)
Pliers
Allen wrench(3/16”)
Water filter
Hex wrench
Fastener
Compression fitting
Compression nut
Clip fitting lock(red)
Required Tools (Not provided)
Some installations require door removal to transport the Refrigerator to its final location.
Do not remove the door/drawer if it is not needed. Before removing the door/drawer, make sure you read
following items.
Disconnect power to the Refrigerator before removing the door or drawer.
WARNING
Be careful not to drop and scratch the doors while removing the
doors.
WARNING
•
Be careful not to drop, damage or scratch the door/drawer while removing them.
•
Be careful not to get injured while removing the door/drawer.
•
Reattach the door/drawer properly to avoid:
- Moisture from air leakage.
- Uneven door alignment.
- Wasting energy due to improper door seal.
Check the accessories listed below.
2
1
Disassemble the Refrigerator doors
Disassemble the Refrigerator doors
1. With the door opened, remove the cap top table (
1
) with
a flat-blade screwdriver(-), and close the door.
Remove the 3 screws holding down the top table (
2
) and
remove it.