Samsung SP-P410ME Owners Manual - Page 10

Make sure to place your remote control on, ened with neutral detergent and water.

Get Samsung SP-P410ME PDF manuals and user guides View all Samsung SP-P410ME manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

When cleaning the product, disconnect the power cord and clean the product with a soft dry cloth. • Avoid using chemicals such as wax, benzene, alcohol, thinner, mosquitorepellent, fragrance, lubrication or cleansing agent when cleaning the product. This may result in the exterior being deformed or the print being removed. When not using the product for a long time, such as leaving your home, unplug the power cord from the wall outlet. • Otherwise, it may cause dust accumulation and result in fire caused by overheating or a short circuit or result in an electric shock. If the product is installed in a location where the operating conditions vary considerably, a serious quality problem may occur due to the surrounding environment. In this case, install the product only after consulting our Call Center. • Places exposed to microscopic dust, chemicals, too high or low temperature, high humidity, such as airports or stations where the product is continuously used for a long time etc.. If you drop the product or the case is damaged, turn the power off and unplug the power cord. Contact a service center. • Failing to do so may result in fire or electric shock. Make sure to place your remote control on a table or desk. • If you step on the remote control, you may fall and hurt yourself or the product may be damaged. To avoid burning yourself, do not touch the vents or lamp cover while operating or right after turning off the product. Do not open any cover on the product. • This would prove hazardous because of high-voltage current inside the product. Be careful not to touch the ventilation hole while the projector is on. The hot air comes out. 1-3 When a gas leak occurs, do not touch the product or the power plug and ventilate immediately. • A spark may result in an explosion or fire. • During a thunder or lighting storm, do not touch the power cord or antenna cable Do not touch the lens on the product. • This may cause damage to the lens. Do not touch any outer part of the product with tools such as a knife or a hammer. To clean dirt or stains on the front projection lens, use spray or a wet cloth dampened with neutral detergent and water. Ask a Service Center to clean the interior of the projector at least once per year. Do not clean the product using water spray or a wet cloth. Avoid using any chemicals such as detergents, industrial or automotive polish, abrasive, wax, benzene, alcohol on any plastic part of the product such as projector case, since this may cause damage. Do not use any undesignated battery. The ventilation hole is hot for some time though the projector is turned off. Keep you hands or body off the ventilation hole. Major Safety Precautions

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
1-3
Major Safety Precautions
When cleaning the product, disconnect the
power cord and clean the product with a
soft dry cloth.
•
Avoid using chemicals such as wax,
benzene, alcohol, thinner, mosquito-
repellent, fragrance, lubrication or
cleansing agent when cleaning the
product.
This may result in the exterior being
deformed or the print being removed.
When a gas leak occurs, do not touch the
product or the power plug and ventilate
immediately.
•
A spark may result in an explosion or
fire.
•
During a thunder or lighting storm, do
not touch the power cord or antenna
cable
When not using the product for a long
time, such as leaving your home, unplug
the power cord from the wall outlet.
•
Otherwise, it may cause dust
accumulation and result in fire caused
by overheating or a short circuit or
result in an electric shock.
Do not touch the lens on the product.
•
This may cause damage to the lens.
If the product is installed in a location
where the operating conditions vary con-
siderably, a serious quality problem may
occur due to the surrounding environment.
In this case, install the product only after
consulting our Call Center.
•
Places exposed to microscopic dust,
chemicals, too high or low temperature,
high humidity, such as airports or
stations where the product is
continuously used for a long time
etc..
Do not touch any outer part of the product
with tools such as a knife or a hammer.
If you drop the product or the case is dam-
aged, turn the power off and unplug the
power cord. Contact a service center.
•
Failing to do so may result in fire or
electric shock.
To clean dirt or stains on the front projec-
tion lens, use spray or a wet cloth damp-
ened with neutral detergent and water.
Make sure to place your remote control on
a table or desk.
•
If you step on the remote control, you
may fall and hurt yourself or the
product may be damaged.
Ask a Service Center to clean the
interior
of the projector at least once per year.
To avoid burning yourself, do not touch the
vents or lamp cover while operating or
right after turning off the product.
Do not clean the product using water spray
or a wet cloth. Avoid using any chemicals
such as detergents, industrial or automo-
tive polish, abrasive, wax, benzene, alco-
hol on any plastic part of the product such
as projector case, since this may cause
damage.
Do not open any cover on the product.
•
This would prove hazardous because
of high-voltage current inside the
product.
Do not use any undesignated battery.
Be careful not to touch the ventilation hole
while the projector is on. The hot air comes
out.
The ventilation hole is hot for some time
though the projector is turned off. Keep
you hands or body off the ventilation hole.