Samsung WA46CG3505AWA4 User Manual - Page 27

Step 5, Step 6

Get Samsung WA46CG3505AWA4 PDF manuals and user guides View all Samsung WA46CG3505AWA4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

STEP 5 Power on Plug the power cord into an AC 120 V / 60 Hz / 15 AMP approved electrical outlet protected by a 15-amp fuse or circuit breaker. Then, press POWER to turn on the washer. STEP 6 Run a test cycle Run a test cycle as follows to check if your washer is properly installed. 1. Load about 6 lb. of laundry into the tub. 2. Press POWER to turn on your washer. 3. Turn the Cycle Selector to RINSE+SPIN. 4. Press and hold START/PAUSE to start the test cycle. 5. The washer should not rock or vibrate excessively when water is supplied or when washing and spinning, and should drain well during the spin cycle. NOTE • If water leaks while water is being supplied or drained, check the water connections. See "Connect the water hose" on page 22. • If the washer rocks and vibrates excessively, level your washer again. See "Level the washer" on page 25. Installation Untitled-20 27 English 27 2023-06-22 6:12:04

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
English
27
Installation
STEP 5
Power on
Plug the power cord into an AC 120 V / 60 Hz / 15 AMP approved electrical outlet
protected by a 15-amp fuse or circuit breaker. Then, press
POWER
to turn on the washer.
STEP 6
Run a test cycle
Run a test cycle as follows to check if your washer is properly installed.
1.
Load about 6 lb. of laundry into the tub.
2.
Press
POWER
to turn on your washer.
3.
Turn the
Cycle Selector
to
RINSE+SPIN
.
4.
Press and hold
START/PAUSE
to start the test cycle.
5.
The washer should not rock or vibrate excessively when water is supplied or when
washing and spinning, and should drain well during the spin cycle.
NOTE
•
If water leaks while water is being supplied or drained, check the water connections.
See “
Connect the water hose
” on page
22
.
•
If the washer rocks and vibrates excessively, level your washer again. See “
Level the
washer
” on page
25
.
Untitled-20 27
Untitled-20
27
2023-06-22 6:12:04
2023-06-22
6:12:04