Samsung WA476DSHAWR/A1 User Manual Ver.1.0 (English, French, Spanish) - Page 18

Step 3, Step 4, Step 5

Get Samsung WA476DSHAWR/A1 PDF manuals and user guides View all Samsung WA476DSHAWR/A1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

installing your washer STEP 3 Leveling your washer See if the washer is level by checking the position of the tub: 1. Slide the washer into position. 2. Open the lid of the washer, and pour the water into the tub to just below the pulsator level. Pulsator Loosen Lock Adjustable legs 3. If the washer is level, the pulsator is positioned at the center of the water as shown in the figure. If not, level your washer by turning the front leveling feet in or out as necessary. Turn the front leveling feet clockwise to raise the height, and counter clockwise to lower the washer. STEP 4 Powering your washer Plug the power cord into a 3-prong, well grounded 120 volt 60 Hz approved electrical outlet protected by a 15-amp fuse or comparable circuit breaker. Your washer is grounded through the third prong of the power cord when plugged into a three-prong grounded electrical outlet. STEP 5 Running a test cycle Run a test cycle as follows to check if your washer is properly installed. 1. Load your laundry (6 pounds) into the tub. 2. Press the Power button to turn on your washer. 3. Select the Rinse+Spin cycle by turning the Cycle Selector. 4. Press the Start/Pause button to start the test cycle. 5. Check if the washer does not rock or vibrate excessively while water is supplied, and that it drains well during the spin cycle. If there are any malfunctions such as a water leakage while water is supplied or drained, check the water connection, referring to the "Connecting the water and the drain" section on page 16~17. If the washer rocks and vibrates excessively, level your washer again, referring to the "Leveling your washer" section on page 18. 18_ installing your washer WA484DSHA-03050D_EN.indd Sec3:18 2012-07-02 3:39:21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
18_
installing your washer
installing your washer
STEP 3
Leveling your washer
See if the washer is level by checking the position of the tub:
1.
Slide the washer into position.
2.
Open the lid of the washer, and pour the water into the tub to
just below the pulsator level.
3.
If the washer is level, the pulsator is positioned at the center of the
water as shown in the figure. If not, level your washer by turning the
front leveling feet in or out as necessary.
Turn the front leveling feet clockwise to raise the height, and
counter clockwise to lower the washer.
STEP 4
Powering your washer
Plug the power cord into a 3-prong, well grounded 120 volt 60
Hz approved electrical outlet protected by a 15-amp fuse or
comparable circuit breaker.
Your washer is grounded through the third prong of the power
cord when plugged into a three-prong grounded electrical outlet.
STEP 5
Running a test cycle
Run a test cycle as follows to check if your washer is properly installed.
1.
Load your laundry (6 pounds) into the tub.
2.
Press the
Power
button to turn on your washer.
3.
Select the
Rinse+Spin
cycle by turning the
Cycle Selector
.
4.
Press the
Start/Pause
button to start the test cycle.
5.
Check if the washer does not rock or vibrate excessively while water is supplied, and that it
drains well during the spin cycle.
If there are any malfunctions such as a water leakage while water is supplied or
drained, check the water connection, referring to the “Connecting the water and the
drain” section on page 16~17.
If the washer rocks and vibrates excessively, level your washer again, referring to the
“Leveling your washer” section on page 18.
Loosen
Lock
Pulsator
Adjustable legs
WA484DSHA-03050D_EN.indd Sec3:18
WA484DSHA-03050D_EN.indd
Sec3:18
2012-07-02
3:39:21
2012-07-02
3:39:21