Samsung WF393BTPARA/A2 User Manual Ver.1.0 (English, French, Spanish) - Page 17

Important Note To Installer

Get Samsung WF393BTPARA/A2 PDF manuals and user guides View all Samsung WF393BTPARA/A2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

01 Installing your washer IMPORTANT NOTE TO INSTALLER Please read the following instructions carefully before installing the washer. These instructions should be retained for future reference. We recommend you hire a professional to install this washer. Installation flow chart Selecting a location Removing the shipping bolts (*Drum only) Connecting the water and the drain Please check again before steps. Adjusting the levelling feet Powering your washing machine [Running a test cycle] Run a test cycle (Rinse+Spin) with small amount of laundary (about 4~5 Towels) Does your washer have excess vibration Yes or noise? Running a Calibration mode (Refer to the following No description) Finish the installation STEP 1 Removing the Shipping Bolts Before using your washer, you must remove all shipping bolts from the back of the unit. 1. Loosen all the bolts with the supplied wrench. 2. Slide the bolt and spacer up and remove the bolt with the spacer through the hole in the rear wall of your washer. Repeat for each bolt. 3. Cover the holes with the supplied Bolt Hole Covers (See page 13). 4. Keep the shipping bolts and spacers for future use. STEP 2 Selecting a Location Before you install your washer, make sure the location: • Has a hard, level surface • Is away from direct sunlight • Has adequate ventilation • Will not freeze (tempuratures are never below 32 °F or 0 °C). • Is away from heat sources such as oil or gas • Has enough room for the power cord. • Doesn't have any carpeting that will obstruct ventilation openings. WF395BTPA-03145B-02_EN_20120829.indd Sec2:17 Installing your washer _17 2012-08-31 12:36:20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
Installing your washer
_17
IMPORTANT NOTE TO INSTALLER
Please read the following instructions carefully before installing the washer.
These instructions should be retained for future reference.
We recommend you hire a professional to install this washer.
Installation flow chart
STEP 1
Removing the Shipping Bolts
Before using your washer, you must remove all shipping bolts from the
back of the unit.
1.
Loosen all the bolts with the supplied wrench.
2.
Slide the bolt and spacer up and remove the bolt with the spacer
through the hole in the rear wall of your washer. Repeat for each
bolt.
3.
Cover the holes with the supplied Bolt Hole Covers (See page 13).
4.
Keep the shipping bolts and spacers for future use.
STEP 2
Selecting a Location
Before you install your washer, make sure the location:
•
Has a hard, level surface
•
Is away from direct sunlight
•
Has adequate ventilation
•
Will not freeze (tempuratures are never below 32 °F or 0 °C).
•
Is away from heat sources such as oil or gas
•
Has enough room for the power cord.
•
Doesn’t have any carpeting that will obstruct ventilation openings.
01 Installing your washer
Selecting a
location
Running a Calibration mode
(Refer to the following
description)
Finish the
installation
Removing the shipping
bolts (*Drum only)
Connecting the water
and the drain
Adjusting the
levelling feet
Powering your washing
machine
[Running a test cycle]
Run a test cycle (Rinse+Spin) with
small amount of laundary
(about 4~5 Towels)
Yes
Please
check again
before
steps.
No
Does
your washer
have excess vibration
or noise?
WF395BTPA-03145B-02_EN_20120829.indd Sec2:17
WF395BTPA-03145B-02_EN_20120829.indd
Sec2:17
2012-08-31
12:36:20
2012-08-31
12:36:20