Samsung WF393BTPARA/A2 User Manual Ver.1.0 (English, French, Spanish) - Page 18

Installing your Washer

Get Samsung WF393BTPARA/A2 PDF manuals and user guides View all Samsung WF393BTPARA/A2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

installing your washer STEP 3 Installing your Washer 1. If you use a stand pipe, make sure the connection between the drain hose and the standpipe is NOT airtight. The standpipe must be at least 18 in or 46 cm high. You must always exercise caution to avoid collapsing or damaging the drain hose. For best results, the drain hose should not be restricted in any way - by elbows, couplings, or excessive length. For situations where the drain hose cannot 96" Max 18" Min be conveniently elevated to at least 18 in or 46 cm, the drain hose must be supported. Laundry tub Stand pipe Hose retainer Tie strap 96" Max 18" Min Do not insert the drain hose too far into the stand pipe: 6 - 8 inches, and no more. Cold 2. Check the inlet hose to ensure a washer is inside each fill hose. Thread the inlet hoses to the HOT and COLD faucet connections. On the other end of the hose, check for one rubber washer per hose and attach each fill hose to the water valve. Make sure the hose with Hot printed on it is attached to the HOT faucet. Tighten by hand until snug, then two-thirds of a turn with pliers. For correct water use, connect both HOT and COLD water valves. If either or both are not connected, an "nF" (no fill) error can occur. Hot Rubber Washer 18_ Installing your washer WF395BTPA-03145B-02_EN_20120829.indd Sec2:18 2012-08-31 12:36:20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
18_
Installing your washer
installing your washer
STEP 3
Installing your Washer
1.
If you use a stand pipe, make sure the connection
between the drain hose and the standpipe is NOT
airtight. The standpipe must be at least 18 in or 46
cm high.
You must always exercise caution to avoid
collapsing or damaging the drain hose. For best
results, the drain hose should not be restricted
in any way – by elbows, couplings, or excessive
length. For situations where the drain hose cannot
be conveniently elevated to at least 18 in or 46 cm,
the drain hose must be supported.
Do not insert the drain hose too far into the stand
pipe: 6 - 8 inches, and no more.
2.
Check the inlet hose to ensure a washer is inside each fill hose.
Thread the inlet hoses to the HOT and COLD faucet connections.
On the other end of the hose, check for one rubber washer per hose
and attach each fill hose to the water valve. Make sure the hose with
Hot printed on it is attached to the HOT faucet. Tighten by hand until
snug, then two-thirds of a turn with pliers.
For correct water use, connect both HOT and COLD water valves. If
either or both are not connected, an “nF” (no fill) error can occur.
96” Max
18” Min
96” Max
18” Min
Hose
retainer
Tie strap
Laundry tub
Stand pipe
Cold
Hot
Rubber
Washer
WF395BTPA-03145B-02_EN_20120829.indd Sec2:18
WF395BTPA-03145B-02_EN_20120829.indd
Sec2:18
2012-08-31
12:36:20
2012-08-31
12:36:20