Sanyo PLC-WXU30A Owner's Manual
Sanyo PLC-WXU30A - 3700 Lumens Manual
 |
UPC - 086483076350
View all Sanyo PLC-WXU30A manuals
Add to My Manuals
Save this manual to your list of manuals |
Sanyo PLC-WXU30A manual content summary:
- Sanyo PLC-WXU30A | Owner's Manual - Page 1
Multimedia Projector MODEL PLC-WXU30 Network Supported ❏ Wireless LAN IEEE802.11b/g ❏ Wired LAN 100-Base-TX/10-Base-T Memory Viewer ❏ SD Card Memory Viewer ✽Refer to the owner's manuals below for details about network and memory viewer function. ■ Network Set-up and Operation ■Memory - Sanyo PLC-WXU30A | Owner's Manual - Page 2
- Sanyo PLC-WXU30A | Owner's Manual - Page 3
matrix liquid crystal display (LCD) technology. ◆ Compact Design This projector is designed compact in and maintains the lamp life (p.52). ◆ Lamp Control Brightness of the projection lamp can be is not supplied with the projector. For details, refer to the owner's manual of Memory viewer. ◆ Input - Sanyo PLC-WXU30A | Owner's Manual - Page 4
Instructions 6 Air Circulation 7 Moving the Projector 7 Installing the Projector 32 Auto PC Adjustment 33 Manual PC Adjustment 34 Image Projector Cabinet 64 Lamp Replacement 65 Resetting the Lamp Counter 66 Appendix 67 Troubleshooting 67 Menu Tree 71 Indicators and Projector - Sanyo PLC-WXU30A | Owner's Manual - Page 5
operate improperly, read this manual again, check operations and cable connections and try the solutions in the "Troubleshooting" section in the back of this booklet. If the problem still persists, contact the dealer where you purchased the projector or the service center. CAUTION RISK OF ELECTRIC - Sanyo PLC-WXU30A | Owner's Manual - Page 6
or sold with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the . Refer all servicing to qualified service personnel. Unplug this projector from wall outlet and refer servicing to qualified service personnel under the - Sanyo PLC-WXU30A | Owner's Manual - Page 7
by heat. Cooling fans are provided to cool down the projector. The fans' running speed is changed according to the temperature inside the projector. Air Intake Vent Safety Instructions Moving the Projector When moving the projector, replace the lens cover and retract adjustable feet to prevent - Sanyo PLC-WXU30A | Owner's Manual - Page 8
Safety Instructions Installing the Projector in Proper Directions Use the projector properly in specified positions. Improper positioning may reduce the lamp life and result in severe accident or fire hazard. This projector can project the picture upward, downward, or backward, perpendicular to the - Sanyo PLC-WXU30A | Owner's Manual - Page 9
to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Number : PLC-WXU30 Trade Name : Sanyo Responsible party : SANYO FISHER COMPANY Address : 21605 Plummer Street - Sanyo PLC-WXU30A | Owner's Manual - Page 10
turn on a projector with lens cap attached. High temperature from light beam may damage Slot !6 LAN Connection Terminal !7 Lamp Cover !8 Filter !9 Battery Cover manual "Network Set-up and Operation". ✽ Kensington Security Slot This slot is for a Kensington lock used to deter theft of the projector - Sanyo PLC-WXU30A | Owner's Manual - Page 11
) (pp.13, 19). e SERVICE PORT This jack is used to service the projector. r COMPUTER IN 2/COMPONENT IN Connect the LAN cable (refer to the owner's manual "Network Set-up and Operation"). i ALARM buttons SD card.When inserting SD Card, the indicator lights, and when removing SD Card, the indicator - Sanyo PLC-WXU30A | Owner's Manual - Page 12
Blinks red when informing the setting or battery status (pp.58-59). w LAMP REPLACE indicator Lights yellow when the projection lamp reaches its end of life (pp.65, 71). e ON/STAND-BY button Turn the projector owner's manual of "Network Set-up and Operation" and owner's manual of Memory viewer. !1 MENU - Sanyo PLC-WXU30A | Owner's Manual - Page 13
. To use these buttons, connect the projector and your computer with a USB cable. (pp.11, 19) !5 LAMP CONTROL button Select a lamp mode. (pp.28, 53) !6 Viewer menu. Refer to the owner's manual of "Network Set-up and Operation" and owner's manual of Memory viewer. @6 NETWORK button Select the Network - Sanyo PLC-WXU30A | Owner's Manual - Page 14
has switched to the Pointer, use the LASER button as the Pointer function ON-OFF switch. Press the LASER button pointing toward the projector and see if it lights green. ✔Note: • You can choose the size of Spotlight (Large/Middle/ Small) and the pattern of Pointer (Arrow/Finger/Dot) in the Setting - Sanyo PLC-WXU30A | Owner's Manual - Page 15
19. When the Pointer function is used, the wireless mouse is not available. 2 When a USB cable is connected to the computer and the projector, turn on the projector first, then the computer. If you turn on the computer first, the wireless mouse function may not operate correctly. Part Names and - Sanyo PLC-WXU30A | Owner's Manual - Page 16
if battery is replaced by an incorrect type. ● Dispose of used batteries according to the instructions. Remote Control Operating Range Point the remote control toward the projector (Infrared Remote Receiver) when pressing the buttons. Maximum operating range for the remote control is about - Sanyo PLC-WXU30A | Owner's Manual - Page 17
Projector For projector positioning, see the figures below. The projector should be set perpendicularly to the plane of the screen. ✔Notes: • The brightness in the room has a great influence on picture quality. It is recommended to limit ambient lighting H) mm 16 : 10 aspect ratio Zoom (min) Zoom ( - Sanyo PLC-WXU30A | Owner's Manual - Page 18
of the type of power being supplied, consult your authorized dealer or service station. Connect the projector with all peripheral equipment before turning the projector on. Connect the AC power cord (supplied) to the projector. The AC outlet must be near this equipment and must be easily accessible - Sanyo PLC-WXU30A | Owner's Manual - Page 19
terminal when using the COMPUTER IN 1/DVI-I and the COMPUTER IN 2/ COMPONENT IN terminal as input. • When the AUDIO OUT is plugged-in, the projector's built-in speaker is not available. • USB cable connection is needed when operating the computer with the remote control or using the PAGE ed buttons - Sanyo PLC-WXU30A | Owner's Manual - Page 20
Audio Input AUDIO IN VIDEO S-VIDEO Audio cable (stereo) KB3AC SD AUDIO OUT (stereo) ✔Notes: • When the AUDIO OUT is plugged-in, the projector's builtin speaker is not available. • The S-VIDEO jack connection overrides the VIDEO jack connection when selecting AUTO in the Input Menu (p.40). 20 - Sanyo PLC-WXU30A | Owner's Manual - Page 21
IN COMPUTER/ COMPONENT AUDIO IN External Audio Equipment Audio Input Audio cable (stereo) KB3AC ✔Notes: • When the AUDIO OUT is plugged-in, the projector's built-in speaker is not available. • See page 77 for ordering optional cables. • RGB Scart signal cannot be output from the MONITOR OUT - Sanyo PLC-WXU30A | Owner's Manual - Page 22
lamp control status icon (see page 53) appear on the screen. If the projector is locked with a PIN code, PIN code input dialog box will appear. Enter the PIN code as instructed of this manual and keep it at hand. Should the PIN code be missing or forgotten, consult your dealer or service center. 22 - Sanyo PLC-WXU30A | Owner's Manual - Page 23
changed according to the temperature inside the projector. • Do not put the projector in a case before the projector is cooled enough. • If the WARNING indicator blinks or lights red, see "Warning Indicators" on page 62. • While the POWER indicator is blinking, the lamp is being cooled down and the - Sanyo PLC-WXU30A | Owner's Manual - Page 24
Basic Operation How to Operate the On-Screen Menu The projector can be adjusted or set via the On-Screen Menu. For each adjustment and setting procedure, refer to the respective sections in this manual. 1 Press the MENU button on the top control or the remote control to display the On-Screen Menu - Sanyo PLC-WXU30A | Owner's Manual - Page 25
72. Basic Operation For computer source Guide Window Show the selected Menu of image mode among of the image [Normal/ the projector's Dynamic, Standard, Real, True/Full/Custom/Digital mute the sound (p.27). Wired Menu See owner's manual "Network Set-up and Operation". For video source Input - Sanyo PLC-WXU30A | Owner's Manual - Page 26
correct Keystone distortion according to the projector's tilt and adjust the computer display correct horizontal distortion. • Auto Keystone cannot work when Ceiling feature is set to "On" in the Setting on the remote control, correct the image manually as follows: Press the KEYSTONE button on - Sanyo PLC-WXU30A | Owner's Manual - Page 27
Basic Operation Sound Adjustment Direct Operation Volume Press the VOLUME+/- buttons on the top control or on the remote control to adjust the volume. The volume dialog box appears on the screen for a few seconds. Mute Press the MUTE button on the remote control to temporarily turn off the sound. - Sanyo PLC-WXU30A | Owner's Manual - Page 28
source. See pages 3031, 40-41 for details. Refer to the owner's manual "Network Set-up and Operation" for details about the network input. FREEZE by pressing this button. See page 33 for details. D.ZOOM buttons LAMP CONTROL button NO SHOW button P-TIMER button IMAGE button D.ZOOM buttons Press - Sanyo PLC-WXU30A | Owner's Manual - Page 29
NO SHOW button Press the NO SHOW button on the remote control to black out the image. To restore to normal, press the NO SHOW button again or press any other button. When a projected image is captured and set as "User" in the Logo selection (see page 49), the screen changes each time you press the - Sanyo PLC-WXU30A | Owner's Manual - Page 30
to Computer 1 (Analog) and press the SELECT button. Input Menu Input Menu icon ✔Notes: • Wired and Wireless are for the Network function. See owner's manual "Network Set-up and Operation" . • When the Input Search function is set to "On1" or "On2", the input signal will be searched automatically - Sanyo PLC-WXU30A | Owner's Manual - Page 31
and controlled by Digital Content Protection, LLC. Should the specification be changed, this projector may not display the digital content protected by HDCP. • Wired and Wireless are for the Network function. See owner's manual "Network Set-up and Operation" . • When the Input Search function is set - Sanyo PLC-WXU30A | Owner's Manual - Page 32
WXGA, or UXGA with its Multi-scan system and Auto PC Adjustment. If a computer is selected as a signal source, this projector Check the connection between your computer and the projector. (See "Troubleshooting" on page 67.) The preset system is manually adjusted in the PC Adjust Menu. The - Sanyo PLC-WXU30A | Owner's Manual - Page 33
The adjusted parameters from the Auto PC Adjustment can be stored in the projector. Once the parameters are stored, the setting can be done just by selecting function. When the image is not provided properly with this operation, manual adjustments are required (pp.34-35). • The Auto PC Adjustment - Sanyo PLC-WXU30A | Owner's Manual - Page 34
PC Adjustment enables you to precisely adjust several parameters to match those signal formats. The projector has five independent memory areas to store those parameters manually adjusted. It allows you to recall the setting for a specific computer. 1 Press the MENU button to display the On-Screen - Sanyo PLC-WXU30A | Owner's Manual - Page 35
Input Display area H Use the Point 7 8 buttons to adjust the horizontal area displayed by this projector. Display area V Use the Point 7 8 buttons to adjust the vertical area displayed by this projector. Reset To reset the adjusted data, select Reset and press the SELECT button. A confirmation box - Sanyo PLC-WXU30A | Owner's Manual - Page 36
by pressing the IMAGE button on the remote control. Dynamic For viewing pictures in a bright room. Standard Normal picture mode preset on the projector. Real Picture mode with improved halftone for graphics. Blackboard (Green) For the image projected on a blackboard. This mode help enhance the image - Sanyo PLC-WXU30A | Owner's Manual - Page 37
Image Adjustment 1 Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the Image Adjust Menu icon. 2 Use the Point ed buttons to move the red frame pointer to the desired item and then press the SELECT button to display the adjustment - Sanyo PLC-WXU30A | Owner's Manual - Page 38
the screen size. True Provide the image in its original size. When the original image size is larger than the screen size (1280 x 800), the projector enters to the panning mode automatically. Use the Point ed7 8 buttons to pan the image. When adjusted, the arrows will turn red. When reached to - Sanyo PLC-WXU30A | Owner's Manual - Page 39
fixed. The "Scale V" appears dimmed and becomes unavailable. Adjust "Scale H," then the screen scale is automatically modified based on the aspect ratio. Position H/V....... Adjust the Horizontal/Vertical screen position. Common Save the adjusted scale to all the inputs. Press the SELECT button at - Sanyo PLC-WXU30A | Owner's Manual - Page 40
Auto, the projector automatically detects incoming video signal, and adjusts itself to optimize its performance. The projector selects connection ✔Notes: • Wired and Wireless are for the Network function. See the owner's manual "Network Set-up and Operation" . • When the Input Search function is set - Sanyo PLC-WXU30A | Owner's Manual - Page 41
the COMPUTER IN 2/COMPONENT IN terminal with a ScartVGA Cable, select RGB (Scart). ✔Note: • Wired and Wireless are for the Network function. See owner's manual "Network Set-up and Operation" . • When the Input Search function is set to "On1" or "On2", the input signal will be searched automatically - Sanyo PLC-WXU30A | Owner's Manual - Page 42
system, and adjusts itself to optimize its performance. When Video System is PAL-M or PAL-N, select the system manually. PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N If the projector cannot reproduce proper video image, select a specific broadcast signal format from among PAL, SECAM, NTSC, NTSC 4.43, PAL - Sanyo PLC-WXU30A | Owner's Manual - Page 43
by pressing the IMAGE button on the remote control. Dynamic For viewing pictures in a bright room. Standard Normal picture mode preset on the projector. Cinema Picture mode adjusted with fine tone. Blackboard (Green) For the image projected on a blackboard. This mode help enhance the image projected - Sanyo PLC-WXU30A | Owner's Manual - Page 44
Video Input Image Adjustment 1 Press the MENU button to display the On-Screen Menu. Use the Point 7 8 buttons to move the red frame pointer to the Image Adjust Menu icon. 2 Use the Point ed buttons to move the red frame pointer to the desired item and then press the SELECT button to display the - Sanyo PLC-WXU30A | Owner's Manual - Page 45
options. Off.......... Disabled. L1........... For an active picture. L2........... For a still picture. Film........ For watching a film. With this function, the projector reproduces pictures faithful to the original film quality. Reset To reset the adjusted data, select Reset and press the SELECT - Sanyo PLC-WXU30A | Owner's Manual - Page 46
Video Input Screen Size Adjustment This projector has the picture screen resize function, which enables the SELECT button. NW Screen Menu icon Normal Provide the image at the 4:3 normal video aspect ratio. Move the red frame pointer to the desired function and press the SELECT button. Zoom - Sanyo PLC-WXU30A | Owner's Manual - Page 47
. . . . Always works and corrects keystone distortion according to the projector's tilt. Manual . . . Works only when pressing the AUTO SET/ CANCEL button on , not correct horizontal distortion. • The Auto Keystone cannot work when Ceiling feature is set "On" in the Setting menu (p.51). • Perfect - Sanyo PLC-WXU30A | Owner's Manual - Page 48
. Countdown Off......... Show the input image instead of the countdown when turning on the projector. Use this function when you want to project the image as early as possible even when the lamp is not bright enough. Off Hide the On-Screen Displays except; ●On-Screen Menu ●"Power - Sanyo PLC-WXU30A | Owner's Manual - Page 49
Then the captured image will be displayed the next time you turn on the projector or when you press the NO SHOW button (see page 29). To cancel the by the Keystone function, the adjusted data is automatically reset and the projector captures an image without keystone correction. • When the Logo PIN - Sanyo PLC-WXU30A | Owner's Manual - Page 50
-digit number. After entering the four-digit number, move the pointer to "Set." Press the SELECT button so that you can start to operate the projector. If you entered an incorrect Logo PIN code, "Logo PIN code" and the number will turn red for a moment. Enter the correct Logo PIN code - Sanyo PLC-WXU30A | Owner's Manual - Page 51
reversed. This function is used to project the image from a ceiling-mounted projector. Ceiling Rear When this function is set to "On," the picture will search is set to "On1" or "On2," the status of Input and Lamp are displayed every time the signal is switched. • Only the last selected input - Sanyo PLC-WXU30A | Owner's Manual - Page 52
to the owner's manual "Network Set-up and Operation". ✔Note: • When selecting Normal, the cooling fans may be running depending on the temperature inside the projector even if the projector is turned off. Power management For reducing power consumption as well as maintaining the lamp life, the - Sanyo PLC-WXU30A | Owner's Manual - Page 53
cord to a wall outlet. ✔Note: • Be sure to turn off the projector properly (see "Turning Off the Projector" on page 23). If the projector is turned off in the incorrect sequence, the On start function does not work properly. Lamp control This function allows you to change brightness of the screen - Sanyo PLC-WXU30A | Owner's Manual - Page 54
you do not have the remote control nearby or there is something wrong with your remote control, contact the dealer where you purchased the projector or the service center. Select Key lock. Use the Point ed buttons to choose one of the options and select [Yes] to activate it. PIN code lock - Sanyo PLC-WXU30A | Owner's Manual - Page 55
to "Set." Press the SELECT button so that you can start to operate the projector. If you entered an incorrect PIN code, "PIN code" and the number will 80, and keep it securely. If you forget your PIN code, the projector can no longer be started. Change the PIN code Alarm This function allows you - Sanyo PLC-WXU30A | Owner's Manual - Page 56
method. Otherwise, the cooling fans will not work properly and that causes malfunctions of the projector and decreases the lamp life. Be sure to set the Fan control in MAX in the setting menu when the projector is inclined between +40 degrees to +140 degrees to the horizontal plane. Warning log This - Sanyo PLC-WXU30A | Owner's Manual - Page 57
to set a frequency for the filter cleaning. When the projector reached a specified time between cleanings, a Filter warning icon appears values except for the user logo, PIN code lock, Logo PIN code lock, lamp counter, and filter counter to the factory default settings. Quit Exit the Setting Menu - Sanyo PLC-WXU30A | Owner's Manual - Page 58
made without an AC power connection. Set the alarm Press the F button three times to turn the alarm function on. The ALARM indicator blinks for a few seconds and the projector enters the warning mode. (If the battery is not charged enough for the alarm function to operate normally, it bleeps and the - Sanyo PLC-WXU30A | Owner's Manual - Page 59
F button and enter the four-digit PIN code number within about 10 seconds. The ALARM indicator blinks red for a few seconds and a high-pitched confirmation sound is produced. 2 While the indicator is blinking, enter a new PIN code, then you will hear a high-pitched confirmation sound and the ALARM - Sanyo PLC-WXU30A | Owner's Manual - Page 60
save the power and battery life. Replace the rechargeable batteries Use only the specified battery for this projector. Using other types of battery may cause accident or fire hazard. Replacement Battery: SANYO Ni-MH BATTERY PACK Part No. 645 089 8587 How to replace the rechargeable batteries - Sanyo PLC-WXU30A | Owner's Manual - Page 61
Function SAFETY Precautions for SANYO Ni-MH BATTERY PACK Observe the following precautions when handling the built-in battery pack of the projector: ● MAKE SURE THAT THE BATTERY PACK IS INSTALLED IN THE PROJECTOR WHEN RECHARGING. USING THE CHARGERS OTHER THAN THE PROJECTOR MAY CAUSE EXPLOSION OR - Sanyo PLC-WXU30A | Owner's Manual - Page 62
and reconnect it, and then turn the projector on once again to verify operation. If the projector cannot be turned on and the WARNING indicator still lights red, unplug the AC power cord and contact the service station. CAUTION DO NOT LEAVE THE PROJECTOR WITH THE AC POWER CORD CONNECTED UNDER AN - Sanyo PLC-WXU30A | Owner's Manual - Page 63
dusty or smoky conditions, dust may accumulate on a lens, LCD panels, or optical elements inside the projector degrading the quality of a projected image. When the symptoms above are noticed, contact your authorized dealer or service station for proper cleaning. Filter Pull up and remove. ✔Note - Sanyo PLC-WXU30A | Owner's Manual - Page 64
an excessive amount of cleaner. Abrasive cleaners, solvents, or other harsh chemicals might scratch the surface of the cabinet. When the projector is not in use, put the projector in an appropriate carrying case to protect it from dust and scratches. 64 Lens Cover Hole String for the lens cover - Sanyo PLC-WXU30A | Owner's Manual - Page 65
Handle Screw Screw Lamp ORDER REPLACEMENT LAMP Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information to the dealer. ● Model No. of your projector ● Replacement Lamp Type No. : PLC-WXU30 : POA-LMP111 (Service Parts No. 610 - Sanyo PLC-WXU30A | Owner's Manual - Page 66
a new one IMMEDIATELY after the projector has cooled down. (Follow carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion. ● A Lamp may explode as a result of vibration - Sanyo PLC-WXU30A | Owner's Manual - Page 67
connected computer, restart the computer. Problem: - Solutions No power - Plug the power cord of the projector into the AC outlet. - See if the POWER indicator lights red. - Wait until the POWER indicator stops blinking to turn on the projector again. The projector can be turned on after the - Sanyo PLC-WXU30A | Owner's Manual - Page 68
for monitor output when connecting to a projector. See your computer's instruction manual for the setting. - It takes Ceiling funtion.(see page 51) Auto keystone function does not work even when the projector is tipped. - Make sure the Auto keystone function is not set to "Manual". - Sanyo PLC-WXU30A | Owner's Manual - Page 69
rechargeable battery cover.) Indicator blinks or lights. - Chek the status of the projector with referring to "Indicators and projector Condition".(see page 73 ) the dealer where you purchased the projector or the service code lock, Security key lock center. or Security PIN code lock - Sanyo PLC-WXU30A | Owner's Manual - Page 70
again. WARNING : High voltages are used to operate this projector. Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Specify the model number and explain about the - Sanyo PLC-WXU30A | Owner's Manual - Page 71
N/A Go to System (1) Go to System (2) N/A Go to System (3) Go to System (3) Go to System (3) See owner's manual "Network Set-up and Operation" See owner's manual "Network Set-up and Operation" N/A........ not applicable The menu will be displayed device for the input source. when connecting - Sanyo PLC-WXU30A | Owner's Manual - Page 72
Auto PC adj. On/Off Auto keystone Auto Manual Off Keystone Store/Reset Blue back On/Off lock Off/On Logo PIN code change Ceiling Quit Quit On/Off Rear Input search Lamp control Pointer Remote control Security Normal/Auto/Eco Spotlight/Pointer Quit Code 1-Code 8 Key lock Off Projector - Sanyo PLC-WXU30A | Owner's Manual - Page 73
or the service center for service and checkup. Do not leave the projector on. It may cause an electric shock or a fire hazard. • • • green. • • • red • • • off • • • blinks green. • • • blinks red. When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights yellow - Sanyo PLC-WXU30A | Owner's Manual - Page 74
Compatible Computer Specifications Basically this projector can accept the signal from 16 SXGA 17 SXGA 18 SXGA 19 SXGA 20 SXGA+ 1 SXGA+ 2 SXGA+ 3 MAC21 MAC MAC WXGA 1 WXGA 2 WXGA 3 WXGA 4 WXGA 6 WXGA 7 WXGA 8 WXGA 9 UXGA 1 UXGA 2 UXGA 3 UXGA 4 720p 720p 1035i 1080i 1080i RESOLUTION 1152 x 864 1280 - Sanyo PLC-WXU30A | Owner's Manual - Page 75
input signal is digital from DVI terminal, refer to the chart below. ON-SCREEN DISPLAY D-VGA D-480p D-575p D-SVGA D-XGA D-WXGA 1 D-WXGA 2 D-WXGA 3 D-WXGA 4 D-WXGA 5 D-WXGA 6 D-WXGA 7 D-WXGA 9 RESOLUTION 640 x 480 640 x 480 768 x 575 800 x 600 1024 x 768 1366 x 768 1360 x 768 1376 x 768 1360 x 768 - Sanyo PLC-WXU30A | Owner's Manual - Page 76
Projector 334 mm x 78 mm x 257.5mm (Not including adjustable feet) 3.7 kg 0˚ to 8.9˚ Panel Resolution LCD Lamp Adjustable from 40" to 300" 3.3'(1.0 m) -39.7'(12.1m) F1.7-2.5 lens with f=19.2 mm-30.2 mm with manual Audio Input Jack Mini Jack (stereo) x 1 Service Port Connector Mini DIN 8 pin x 1 - Sanyo PLC-WXU30A | Owner's Manual - Page 77
's Manual Quick Reference Guide AC Power Cord Remote Control and Batteries VGA Cable Lens Cover with String PIN Code Label Lamp Replacement Label Alarm Label Network Application (CD-ROM Soft Carrying Case ● The specifications are subject to change without notice. ● LCD panels - Sanyo PLC-WXU30A | Owner's Manual - Page 78
Information System Industries Association). This projector supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class 1. For PJ Link password, see page 49 on the owner's manual "Network Set-up and Operation." Projector Input Computer1 (Analog) Computer1 - Sanyo PLC-WXU30A | Owner's Manual - Page 79
- USB CONNECTOR (Series B) 1 Vcc 21 2 - Data 3 + Data 34 4 Ground LAN TERMINAL 1 TX + 5 ----- 2 TX - 6 RX - 3 RX + 7 ----- 4 ----- 8 ----- 87654321 SERVICE PORT CONNECTOR Terminal : Mini DIN 8-PIN 876 5 43 21 1 RXD 2 ----3 ----4 GND 5 RTS/CTS 6 TXD 7 GND 8 GND 79 - Sanyo PLC-WXU30A | Owner's Manual - Page 80
below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. PIN Code Lock No projector's body while the Antitheft alarm function is set. Lamp Replacement Label When using the projector ceiling-mounted, put the Lamp - Sanyo PLC-WXU30A | Owner's Manual - Page 81
Dimensions Appendix Unit: inch(mm) Screw Holes for Ceiling Mount Screw: M4 Depth: 0.472(12.0) ! ! 81 - Sanyo PLC-WXU30A | Owner's Manual - Page 82
KB3AC SANYO Electric Co., Ltd.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
 |
 |
Multimedia Projector
MODEL
PLC-WXU30
Owner’s Manual
Network Supported
❏
Wireless LAN
IEEE802.11b/g
❏
Wired LAN
100-Base-TX/10-Base-T
Memory Viewer
❏
SD Card Memory Viewer
✽
Refer to the owner’s manuals below for details
about network and memory viewer function.
■
Network Set-up and Operation
■
Memory viewer