Sanyo PLC-WXU30A Owner's Manual - Page 52

Power management, Standby mode

Get Sanyo PLC-WXU30A - 3700 Lumens PDF manuals and user guides
UPC - 086483076350
View all Sanyo PLC-WXU30A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Setting Standby mode This function is available when operating the projector via network. Normal........ Supply the power to the network function even after turning off the projector. You can turn on/ off the projector via network, modify network environment, and receive an e-mail about projector status while the projector is powered off. Eco Select "Eco" when you do not use the projector via network. The projector's network function will stop when turning off the projector. Refer to the owner's manual "Network Set-up and Operation". ✔Note: • When selecting Normal, the cooling fans may be running depending on the temperature inside the projector even if the projector is turned off. Power management For reducing power consumption as well as maintaining the lamp life, the Power management function turns off the projection lamp when the projector is not operated for a certain period. If the input signal is interrupted and no button is pressed for more than 30 seconds, the timer display with "No signal" appears. It starts the countdown until the lamp is turned off. Use the Point 7 8 buttons to set the countdown timer. Select one of the following options: Ready When the lamp has been fully cooled down, the POWER indicator changes to green blinking. In this condition, the projection lamp will be turned on if the input signal is reconnected or any button on the top control or remote control is pressed. Shut down When the lamp has been fully cooled down, the power will be turned off. Off Power management function is off. Power management Time left before Lamp is off. Press the SELECT button at Power management and this dialog box appears. Use the Point 7 8 buttons to choose one of the three options. Press the Point d button to select the timer, and then use the Point 7 8 buttons to set timer. ✔Note: • Factory default is "Ready: 5 min.". 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
5±
Setting
Power management
Time left before Lamp is off.
Power management
For reducing power consumption as well as maintaining
the lamp life, the Power management function turns off the
projection lamp when the projector is not operated for a
certain period.
If the input signal is interrupted and no button is pressed for
more than 30 seconds, the timer display with “No signal”
appears. It starts the countdown until the lamp is turned off.
Use the Point
7 8
buttons to set the countdown timer.
Select one of the following options:
Ready
..................
When the lamp has been fully cooled
down, the POWER indicator changes
to green blinking. In this condition, the
projection lamp will be turned on if the
input signal is reconnected or any button
on the top control or remote control is
pressed.
Shut down
............
When the lamp has been fully cooled
down, the power will be turned off.
Off
........................
Power management function is off.
Standby mode
This function is available when operating the projector via
network.
Normal
.......
Supply the power to the network function even
after turning off the projector. You can turn on/
off the projector via network, modify network
environment, and receive an e-mail about
projector status while the projector is powered
off.
Eco
............
Select “Eco” when you do not use the projector
via network. The projector’s network function
will stop when turning off the projector.
Refer to the owner’s manual “Network Set-up and
Operation”.
✔
Note:
• When selecting Normal, the cooling fans may be running
depending on the temperature inside the projector even
if the projector is turned off.
Press the SELECT button at
Power management and this
dialog box appears. Use the
Point
7 8
buttons to choose
one of the three options.
Press the Point
d
button to
select the timer, and then
use the Point
7 8
buttons to
set timer.
✔
Note:
• Factory default is "Ready: 5 min.".