Sanyo PLC-XU300 Instruction Manual, PLC-XU300 Network Set Up
Sanyo PLC-XU300 - XGA LCD Projector Manual
 |
UPC - 086483073830
View all Sanyo PLC-XU300 manuals
Add to My Manuals
Save this manual to your list of manuals |
Sanyo PLC-XU300 manual content summary:
- Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 1
This is the manual for the Network function. Read this manual thoroughly to operate the Network function. First, read the owner's manual of the projector to understand the basic operation of the projector and the safety instructions. The safety instructions in the owner's manuals should be followed - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 2
turning the equipment off and on, the user is encouraged to try to correct the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Numbers : PLC-XU350, PLC-XU300 Trade Name : Sanyo Responsible party : SANYO FISHER - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 3
Safety instructions CAUTION IN USING THE PROJECTOR VIA NETWORKS ● When you find a problem with the projector, remove the power cable immediately and inspect the unit. Using the projector with failure may cause fire or other accidents. ● If you remotely use the projector via networks, carry out a - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 4
Compliance...2 Federal Communications Commission Notice 2 Safety instructions...3 Table of contents...4 Chapter 1 Preparation 5 Features...6 Required operating environment for computers 7 Network specifications of the projector...7 Flow of installation...9 Notice about installing Software - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 5
Chapter 1 Preparation Describes features and operating environment of this projector. 1 ENGLISH - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 6
software. SNMP Manager function A function to manage the condition of projectors in the network by using the PJ1 SNMP protocol. The man- aging computer needs to provide an SNMP manag- ing software. Refer to the owner's manual of the "PJ Network Manager" sup- plied separately for further - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 7
is recommended) 100MB or more CD-ROM drive Support one of following resolutions; VGA (640 x 480), SVGA(800 x 600), XGA(1,024 x 768) Number of colors: Either of projector. If you do not use the func- tion E-mail Alert, this application is not required. Network specifications of the projector - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 8
manual This manual does not provide the description of basic operation and functions for computer, web browser, projector and network. For instructions . Other product or brand names in this manual are registered trademarks or trademarks of their respective owners. * Unauthorized use of a part or - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 9
software recorded in CD-ROM on each computer which will be operated. Refer to the owner's manual of PJ Network Manager. Notice about installing Software CD-ROM It is available for controlling and setting of the projector by using the web browser without installing any software. So it is not required - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 10
Chapter 1 Preparation 10 - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 11
Chapter 2 Setup Procedures Describes how to configure the network. 2 ENGLISH 11 - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 12
ed but- tons. Then the Menu will disappear, the "Please wait..." message will appear, and switching operation will start. Switching will take a while and the projector's LINK/ACT Lamp will be on or blink, and after completing the operation, the "Please wait..." message will disappear. 12 - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 13
DHCP Sets DHCP function On or Off. When you setup the network setting manually, select "Off". When it is set On, IP address, Subnet, set according to your network environment *1. IP address Sets IP address of the projector Subnet Sets Subnet mask. Normally sets 255.255.255.0 Gateway*2 Sets IP - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 14
you do not want to set the Network PIN code, set "0000". It is recommended to set the Network PIN code if you use the projector via the networks. The Network PIN code can be set also through the networks. See "3. Basic setting and operation" ➔ "Initial setting" ➔ "Network PIN code setting - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 15
Network factory default Network factory default 1. Select "Network factory default" in the Network menu and press SELECT button. 2. A confirmation box appears and select "Yes" and then press SELECT button. 3. Another confirmation box appears and select "Yes" and then press SELECT button. 4. All - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 16
Chapter 2 Setup Procedures Wired LAN factory default settings Parameter IP CONFIGURATION LAN 1 MANUAL SELECTED LAN LAN 2 DHCP LAN 3 MANUAL IP ADDRESS 169.254.100.100 192.168.100.100 192.168.100.100 SUBNET MASK 255.255.0.0 255.255.255.0 255.255.255.0 GATEWAY - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 17
Chapter 3 Basic Setting and Operation Describes basic operations and settings for controlling the projector by using the web browser. It is required that computer and projector is connected to the network and the network address is properly configured. 3 ENGLISH 17 - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 18
login Network PIN code onto the Password text area and then click OK (Log in) button. * The entering User Name must be "user" and it can not be changed. [Note] When accessing the projector for the first time or the Network PIN code "0000" is set, the auto-login will be performed and - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 19
Login the setting page of the projector [3] Display of main setting page The following main setting page will be menu tab. Main menu For selection of control and setting items of the projector. Setting page Displays the control and setting items according to the selected menu. ENGLISH 19 - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 20
3 Basic Setting and Operation How to use the setting page To control and set up the projector, use the setting menus on the web browser. Describes the basic operation and procedures commonly used on this manual. Example of the setting page The setting menu appears when clicking the sub menu tab - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 21
Radio button setting Select an item by selecting a radio button. Check box setting Select items by ticking on check boxes. How to use the setting page ENGLISH 21 - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 22
display the initial setting page. Item Description Language Switches display language on the setting page. English or Japanese. Model name........Indicates the model name of the projector Network PIN code.......Sets the Network PIN code to login the setting page (+p.23) PJLink Switches PJLink - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 23
Class 1 of JBMIA, and it supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class 1. Projector Input Computer 2 Computer 1 Video RGB Component RGB (Scart) Video S-video PJLink Input RGB 1 RGB 2 RGB 3 RGB 4 VIDEO 2 VIDEO 3 Parameter 11 12 13 14 22 - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 24
page again in 10 seconds. Item Description LAN mode Displays the selected LAN mode IP configuration....Sets DHCP or Manual IP address Sets IP address of the projector Subnet mask.......Sets Subnet mask. Normally sets 255.255.255.0 Default gateway*1......Sets IP address of the default gateway - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 25
has an E-mail function which can send an alert message to users or an administrator if it detects an abnormality on the projector or run out of the life span of the lamp. Click E-mail Setting on the main menu and follow the below steps. Item Description SMTP server*1 Sets server name or IP - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 26
is off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby with ON/STANDBY button on the top control or the remote control. ✐ Up to 99,999 - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 27
: Message from projector Projector Model Name: model name TCP/IP: 192.168.1.201 Projector Name: Proj05 It sends you following message. *The Projector lamp is turned off, because Projector power circuit is failed. Unplug the Projector from AC outlet and ask servicing to qualified service personnel - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 28
mail is sent to users in every poweron of the projector. This alert mail will not be sent when unchecking the mail sending condition "When PJ lamp replacement time is reached". ● When lamp corres. value reaches preselect use time: TITLE: Message from projector Projector Model Name: model name TCP/IP - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 29
Setting on the main menu and set up each item. PJ information Item Description Contact Enter user name of the projector etc. (optional) Place Enter place of the projector (optional) Community name(refer).......Enter community name (read only). Default name is "public". Trap Item Description - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 30
is off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby with ON/STANDBY button on the top control or the remote control. ✐ Up to 99,999 - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 31
Chapter 4 Controlling the Projector Describes controlling and setting of the projector by using the web browser. 4 ENGLISH 31 - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 32
window Item Description PJ status Power Displays the status of the lamp. (ON, OFF, On starting up, On cooling down) Status Displays the status of the projector's power. (Refer to next page.) Power control.........Controls the projector power by clicking the "ON" or "Standby" button. ✐ The - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 33
standby mode. Power failure Power failure has occurred inside the projector. Projector is turned off. Unplug the AC cord and ask servicing to a qualified service personnel. When a security (PIN code lock) has been set on the projector, you also cannot control it through the network. To control - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 34
pages and select desired setting items. ✐ Please see the owner's manual of the projector to have the further information of each control item. Input This projector. Source Selects signal source of the input. Computer1 : RGB Component RGB(Scart) Computer2 : RGB Video S-video - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 35
modes (VGA, SVGA, XGA. SXGA, UXGA, WXGA...) which meet the input signal are listed. Available selection at the Video/S-video/Scart input Item Description and 1080i. Sound This function is to adjust the sound of the projector. The values in the text box represent the current control value or - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 36
Chapter 4 Controlling the Projector Image adjustment This function is to adjust may not be available mode depending on the input mode as shown in the table left. Input source Image mode Video Computer Dynamic 4 4 Standard 4 4 Cinema 4 * Real * 4 Blackboard(Green) 4 4 Colorboard 4 - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 37
menu. This function is to adjust the signal from the computer connected to the projector to obtain the proper picture image on the screen. Item Description Current mode......Displays a current mode like VGA, SVGA, XGA. SXGA, UXGA, WXGA, etc. or Mode1 - Mode5 which are the customized mode created - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 38
Screen setting This function is to adjust the screen mode of the projector. The values in the text box represent the current screen status. depending on the input mode as shown in the table below. Input source Screen mode Video Computer Normal True Wide Full Custom 4 4 * 4 4 4 * 4 4 - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 39
projector Manual, OFF) Background.........Sets the screen background when no signal input. (Blue, User the startup. (User, Default, OFF) Setting 2 Item Description Ceiling Sets the image . Lamp control......Selects lamp control mode. (Normal, Eco) Lamp life control Selects lamp life control - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 40
Projector or Remote control. (OFF, Projector keys, Remote warning.....Sets the time to indicate the filter warning message on the screen. (OFF, 100H, 200H, 300H) Factory default..........Sets all of the projector control items to the factory default setting except the following items. Lamp - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 41
. Security Displays the security (PIN code lock) status (Yes, No) PJ time(h) Displays the accumulated use time of the projector. Lamp Corres. Value(h) Displays the use time (Corresponding value) of the lamp. Filter time(h) Displays the accumulated use time of the filter. Indication of the - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 42
Chapter 4 Controlling the Projector 42 - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 43
Chapter 5 Appendix Connection examples Use of telnet Web browser setting Technical data Q & A 5 ENGLISH 43 - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 44
the hub. Hub To another network Computer Name: PC05 IP Address : 192.168.0.5 Subnet Mask : 255.255.255.0 Default Gateway : DNS : Projector Name: PJ01 IP Address : 192.168.0.2 Subnet Mask : 255.255.255.0 Default Gateway : 0.0.0.0 DNS : 0.0.0.0 Computer Name: PC10 IP Address : 192.168 - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 45
. Entrance hall Computer Name IP Address Subnet Mask Default Gateway DNS : PC205 : 192.168.200.5 : 255.255.255.0 : 192.168.200.1 : 192.168.201.1 Projector Name: PJ01 IP Address : 192.168.200.15 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.200.1 DNS : 192.168.201.1 Network Group - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 46
*1 installed on your computer. Normally, the telnet application is available on your computer. * The telnet 10000 port is used to control the projector. Control (For example, in case of using the telnet application of Windows XP Professional.) 1. S elect Run... submenu from Start menu on the - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 47
appears on the window. Type the login password (Network PIN code*2) for the projector and then press "Enter" key on the keyboard. If you do not set on C1D menu display off *1 F urther instructions about the telnet application, please see the on-line guide on your computer. *2 The password is - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 48
not to use this JavaScript function, it may not control the projector properly. In this case, the warning message "Make sure JavaScript is ON." will be displayed on the top of the page. To enable the JavaScript, please see further instructions on the next page. Proxy setting In some cases, your web - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 49
Examples: OS/Browsers Windows XP Professional Web browser setting Internet Explorer v.6.0 ActiveScript setting Select Internet Options from Tools menu on the web browser and then select Security tab and click Customize Level... button. On the security setting window, scroll down and find the - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 50
proxy server address and port correctly in the proxy settings window. For further instruction please consult your network administrator. - Not using proxy server Uncheck the item Use a proxy server. If you connect the projector to the computer directly with UTP cross cable, this must be unchecked - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 51
to which the projector is connected. - Using proxy server When you use an external internet connection from the local area network, select the item Manual proxy configuration. Enter the proxy server address and port number correctly on HTTP Proxy item. For further instruction please consult your - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 52
address and port correctly in Web Proxy Server window. For further instruction please consult your network administrator. - Not using proxy server Uncheck HTTPS) of Select a proxy server to configure. If you connect the projector to the computer directly with UTP cross cable, they must be unchecked - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 53
of LAN cable if the LINK Lamp does not light green. - C heck the network configuration of the projector if the ACT Lamp does not blink orange. 2. Wrong access the projector installed on the company's local area network from a remote location? A There are some ways to access to the projector in the - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 54
Q W e use the DHCP/BOOTP server to assign the IP address. Is it possible to use the projector in this network environment? A P ossible. This projector supports the DHCP/BOOTP server. To use this projector in this network environment, set it up so that the DHCP/BOOTP server does not assign the IP - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 55
The display speed of the page depends on the network environment in which both the projector and computer are placed. It may take much time to complete the page display if the authentication depending on the SMTP server. This projector does not support this kind of SMTP server. 55 ENGLISH - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 56
, they cannot establish communications each other. In this case, the router is placed in the networks to make the routing. Q Can I control the projector by using the telnet application? A Possible. Please refer to the item "Use of telnet" (☞ p.46 - 47). Q What is the MAC address assigned to - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 57
Q&A Q Can I update the firmware of the projector. A It is possible to update the firmware through the network. It is required to have a special tool for the updating. For further information please consult - Sanyo PLC-XU300 | Instruction Manual, PLC-XU300 Network Set Up - Page 58
NETWORK OWNER'S MANUAL SO-KF5AC SANYO Electric Co., Ltd.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
 |
 |
Wired Setting
Projector Set-up and Operation
Owner’s Manual
Network Set-up and Operation
This is the manual for the Network function.
Read this manual thoroughly to operate the Network function.
First, read the owner's manual of the projector to understand the basic
operation of the projector and the safety instructions.
The safety instructions in the owner's manuals should be followed strictly.