Home » Seagate Manuals » Hard Drives » Seagate ST3000DM001 » Manual Viewer

Seagate ST3000DM001 Barracuda 7200.11 SATA Product Manual - Page 39

Note.

View all Seagate ST3000DM001 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Word 104-107 108-111 112-127 128 129-159 160-254 255 Description ATA-reserved The mandatory value of the world wide name (WWN) for the drive. NOTE: This field is valid if word 84, bit 8 is set to 1 indicating 64-bit WWN support. ATA-reserved Security status Seagate-reserved ATA-reserved Integrity word Value 0000H Each drive will have a unique value. 0000H 0001H xxxxH 0000H xxA5H Note. Advanced Power Management (APM) and Automatic Acoustic Management (AAM) features are not supported Note. See the bit descriptions below for words 63, 84, and 88 of the Identify Drive data. Description (if bit is set to 1) Bit Word 63 0 Multiword DMA mode 0 is supported. 1 Multiword DMA mode 1 is supported. 2 Multiword DMA mode 2 is supported. 8 Multiword DMA mode 0 is currently active. 9 Multiword DMA mode 1 is currently active. 10 Multiword DMA mode 2 is currently active. Bit Word 84 0 SMART error loggin is supported. 1 SMART self-test is supported. 2 Media serial number is supported. 3 Media Card Pass Through Command feature set is supported. 4 Streaming feature set is supported. 5 GPL feature set is supported. 6 WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands are supported. 7 WRITE DMA QUEUED FUA EXT command is supported. 8 64-bit World Wide Name is supported. 9-10 Obsolete. 11-12 Reserved for TLC. 13 IDLE IMMEDIATE command with IUNLOAD faeture is supported. 14 Shall be set to 1. 15 Shall be cleared to 0. Barracuda 7200.11 Serial ATA Product Manual, Rev. E 33

Section	Page
1.0 Introduction 1	3
1.1 About the Serial ATA interface 2	3
2.0 Drive specifications 3	3
2.1 Formatted capacity 10	3
2.1.1 LBA mode 10	3
2.2 Default logical geometry 10	3
2.3 Recording and interface technology 10	3
2.4 Physical characteristics 11	3
2.5 Seek time 11	3
2.6 Start/stop times 12	3
2.7 Power specifications 12	3
2.7.1 Power consumption 12	3
2.7.2 Conducted noise 14	3
2.7.3 Voltage tolerance 14	3
2.7.4 Power-management modes 14	3
2.8 Environmental specifications 15	3
2.8.1 Ambient temperature 15	3
2.8.2 Temperature gradient 15	3
2.8.3 Humidity 15	3
2.8.4 Altitude 15	3
2.8.5 Shock 15	3
2.8.6 Vibration 16	3
2.9 Acoustics 17	3
2.9.1 Test for Prominent Discrete Tones (PDTs) 17	3
2.10 Electromagnetic immunity 17	3
2.11 Reliability 18	3
2.11.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF) 18	3
2.12 Agency certification 18	3
2.12.1 Safety certification 18	3
2.12.2 Electromagnetic compatibility 18	3
2.12.3 FCC verification 19	3
2.13 Environmental protection 20	3
2.13.1 European Union Restriction of Hazardous Substances (RoHS) Directive 20	3
2.14 Corrosive environment 20	3
3.0 Configuring and mounting the drive 21	3
3.1 Handling and static-discharge precautions 21	3
3.2 Configuring the drive 22	3
3.3 Serial ATA cables and connectors 23	3
3.4 Drive mounting 24	3
4.0 Serial ATA (SATA) interface 27	3
4.1 Hot-Plug compatibility 27	3
4.2 Serial ATA device plug connector pin definitions 28	3
4.3 Supported ATA commands 29	3
4.3.1 Identify Device command 31	3
4.3.2 Set Features command 35	3
4.3.3 S.M.A.R.T. commands 36	3
5.0 Seagate Technology support services 37	3
Figure 1. Serial ATA connectors 22	5
Figure 2. Attaching SATA cabling 23	5
Figure 3. Mounting dimensions (1500, 1000 and 640 GB models) 24	5
Figure 4. Mounting dimensions (320 and 160 GB models) 25	5
1.0 Introduction	7
1.1 About the Serial ATA interface	8
2.0 Drive specifications	9
2.1 Formatted capacity	16
2.1.1 LBA mode	16
2.2 Default logical geometry	16
2.3 Recording and interface technology	16
2.4 Physical characteristics	17
2.5 Seek time	17
2.6 Start/stop times	18
2.7 Power specifications	18
2.7.1 Power consumption	18
2.7.2 Conducted noise	20
2.7.3 Voltage tolerance	20
2.7.4 Power-management modes	20
2.8 Environmental specifications	21
2.8.1 Ambient temperature	21
2.8.2 Temperature gradient	21
2.8.3 Humidity	21
2.8.3.1 Relative humidity	21
2.8.3.2 Wet bulb temperature	21
2.8.4 Altitude	21
2.8.5 Shock	21
2.8.5.1 Operating shock	21
2.8.5.2 Nonoperating shock	22
2.8.6 Vibration	22
2.8.6.1 Operating vibration	22
2.8.6.2 Nonoperating vibration	22
2.9 Acoustics	23
2.9.1 Test for Prominent Discrete Tones (PDTs)	23
2.10 Electromagnetic immunity	23
2.11 Reliability	24
2.11.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)	24
2.12 Agency certification	24
2.12.1 Safety certification	24
2.12.2 Electromagnetic compatibility	24
2.12.3 FCC verification	25
2.13 Environmental protection	26
2.13.1 European Union Restriction of Hazardous Substances (RoHS) Directive	26
2.14 Corrosive environment	26
3.0 Configuring and mounting the drive	27
3.1 Handling and static-discharge precautions	27
3.2 Configuring the drive	28
3.3 Serial ATA cables and connectors	29
3.4 Drive mounting	30
4.0 Serial ATA (SATA) interface	33
4.1 Hot-Plug compatibility	33
4.2 Serial ATA device plug connector pin definitions	34
4.3 Supported ATA commands	35
4.3.1 Identify Device command	37
4.3.2 Set Features command	41
4.3.3 S.M.A.R.T. commands	42
5.0 Seagate Technology support services	43
Index	45
A	45
B	45
C	45
D	45
E	45
F	45
G	45
H	45
I	46
K	46
L	46
M	46
N	46
O	46
P	46
Q	46
R	46
S	47
T	47
U	47
V	47